ROSE DISPLAYS ANOQUICK ROUND WITH CABLE CLIP AND LOOP AND... User manual

35 Congress Street, Salem, MA 01970
Tel# [phone] Fax# [phone]
e-mail:[e-mail]
Parts
Instruction Sheet
Step 1
Prepare edges of graphic. Place the graphic on
tabletop with one edge at the table edge. Using
the AnoQuick holder, run it across the graphic
edge, crushing it slightly. Fig. 1
Step 2
Starting at one corner, push the holder onto the
graphic. Work your way down the holder tapping
it down firmly to seat the graphic fully. Fig. 2
Step 3
Place cable onto inner channel of Cable Clip. The
cable should snap into place. Fig. 3
Step 4
Align one end of the Cable Clip with the top
channel of the aluminum holder. Then insert one
round end, then press down on the other round
end and slide Cable Clip into rail. Fig. 4
Step 5
Push end caps into place. Fig. 5
Step 6
Suspend poster. Fig. 6
Important note:
Please save and reuse the AnoQuick, Cable Clips,
End Caps and MultiClips for future projects.
Note: Use only
with graphics
mounted on 3/16”
foamboard or other
similar thickness.
Can also use a
folded edge thinner
substrate.
AnoQuick™
Instructions for Hanging
Incept-9.27.02
Figure 2
The AnoQuick is a trademark of Rose Displays, Ltd.. Neither the
manufacturer nor any sales agent may be held liable for injury, loss or
damage resulting from the use of these products.
Part #02INSAnoQuickCableClipLoopSaucer
Figure 3
Figure 5
Figure 4
Figure 1
Figure 6
End Cap
06-5525
AnoQuick
12A300
Cable Clips
06-5050
Loop and
Saucer
16-0018SL

35 Congress Street, Salem, MA 01970
Tel# [phone] Fax# [phone]
e-mail:[e-mail]
Parts
Note: Use only
with graphics
mounted on 3/16”
foamboard or other
similar thickness.
Can also use a
folded edge thinner
substrate.
Instructions for Hanging
OneUp
®
Instruction Sheet
Step 1
Prepare edges of graphic. Place the graphic on
tabletop with one edge at the table edge. Using
the AnoQuick holder, run it across the graphic
edge, crushing it slightly. Fig. 1
Step 2
Starting at one corner, push the holder onto the
graphic. Work your way down the holder tapping
it down firmly to seat the graphic fully. Fig. 2
Step 3
Place cable onto inner channel of Cable Clip. The
cable should snap into place. Fig. 3
Step 4
Align one end of the Cable Clip with the top
channel of the aluminum holder. Then insert one
round end, then press down on the other round
end and slide Cable Clip into rail. Fig. 4
Note: For OneUp applications, the AnoQuick
holder is conveniently marked in the center.
Slide the Cable Clip to the mark.
Step 5
Push end caps into place. Fig. 5
Step 6
Suspend poster. Fig. 6
Important note:
Please save and reuse the AnoQuick, Cable Clips,
End Caps and MultiClip for future projects.
AnoQuick™
Incept-9.27.02
The AnoQuick is a trademark of Rose Displays, Ltd.. Neither the
manufacturer nor any sales agent may be held liable for injury, loss or
damage resulting from the use of these products.
Part #02INSAnoQuickCableClipLoopSaucer
Figure 2
Figure 3
Figure 5
Figure 4
Figure 1
Figure 6
End Cap
06-5525
AnoQuick
12A300
Cable Clip
06-5050
Loop and
Saucer
16-0018SL

Parts
Note: Use only
with graphics
mounted on 3/16”
foamboard or other
similar thickness.
Can also use a
folded edge thinner
substrate.
Instructions for Hanging
Instruction Sheet
AnoQuick
TM
Incept-9.27.02
The AnoQuick is a trademark of Rose Displays, Ltd.. Neither the
manufacturer nor any sales agent may be held liable for injury, loss or
damage resulting from the use of these products.
Part #02INSAnoQuickCableClipLoopSaucer
Step 1
Prepare edges of graphic. Place the graphic on
tabletop with one edge at the table edge. Using
the AnoQuick holder, run it across the graphic
edge, crushing it slightly. Fig. 1
Step 2
Starting at one corner, push the holder onto the
graphic. Work your way down the holder tapping
it down firmly to seat the graphic fully. Fig. 2
Step 3
Place cable onto inner channel of Cable Clip. The
cable should snap into place. Fig. 3
Step 4
Align one end of the Cable Clip with the top
channel of the aluminum holder. Then insert one
round end, then press down on the other round
end and slide Cable Clip into rail. Fig. 4
Step 5
Push end caps into place. Fig. 5
Step 6
Suspend poster. Fig. 6
Important note:
Please save and reuse the AnoQuick, Cable Clips,
End Caps and MultiClips for future projects.
Figure 2
Figure 3
Figure 5
Figure 4
Figure 1
Figure 6
End Cap
06-5525
AnoQuick
12A300
Cable Clips
06-5050
Loop and
Saucer
16-0018SL

Parts
Note: Use only
with graphics
mounted on 3/16”
foamboard or other
similar thickness.
Can also use a
folded edge thinner
substrate.
Instructions for Hanging
OneUp
®
Instruction Sheet
AnoQuick™
Incept-9.27.02
End Cap
06-5525
AnoQuick
12A300
The AnoQuick is a trademark of Rose Displays, Ltd.. Neither the
manufacturer nor any sales agent may be held liable for injury, loss or
damage resulting from the use of these products.
Part #02INSAnoQuickCableClipLoopSaucer
Cable Clip
06-5050
Step 1
Prepare edges of graphic. Place the graphic on
tabletop with one edge at the table edge. Using
the AnoQuick holder, run it across the graphic
edge, crushing it slightly. Fig. 1
Step 2
Starting at one corner, push the holder onto the
graphic. Work your way down the holder tapping
it down firmly to seat the graphic fully. Fig. 2
Step 3
Place cable onto inner channel of Cable Clip. The
cable should snap into place. Fig. 3
Step 4
Align one end of the Cable Clip with the top
channel of the aluminum holder. Then insert one
round end, then press down on the other round
end and slide Cable Clip into rail. Fig. 4
Note: For OneUp applications, the AnoQuick
holder is conveniently marked in the center.
Slide the Cable Clip to the mark.
Step 5
Push end caps into place. Fig. 5
Step 6
Suspend poster. Fig. 6
Important note:
Please save and reuse the AnoQuick, Cable Clips,
End Caps and MultiClip for future projects.
Figure 2
Figure 3
Figure 5
Figure 4
Figure 1
Figure 6
Loop and
Saucer
16-0018SL