Rosin Tech Rosin Tech Pro User manual
Rosin Tech Pro™
Owner’s Manual
1
All Rights Reserved. Copyright © 2018, Rosin Tech Products
Getting Started
2
Initial Set Up:
1) Find a home for your press and try to leave it there. The machine is heavy and
better kept in one place.
2) Follow this step-by-step guide on how to set your temperature and length of press.
Remember to start with a small batch for testing until you lock in your optimal
temperature and length of press.
All Rights Reserved. Copyright © 2018, Rosin Tech Products
ELECTRICAL INFORMATION
3
* SHO PRODUCTS IS NOT RESPONSIBLE FOR ANY
DAMAGE RESULTING FROM IMPROPERING WIRING.
PLEASE CONSULT A PROFESSIONAL PRODUCTS
ELECTRICIAN BEFORE USING THIS MACHINE*
Model Watts Volts Amps
Rosin Tech Pro 800W 110V 7.3A
All Rights Reserved. Copyright © 2018, Rosin Tech Products
* Inside the cabinet of the press you will find the air
regulator. By pulling the black plastic cap upwards,
you can then adjust the pressure by turning the knob
to the right. Please keep PSI under 150*
STEP 1:
PLUG IN / TURN ON
●Once you’ve plugged in your press, and flipped on the power, both LCD screens will
light up and plates will begin heating!
TIP #1: Please note the control panel on the left hand side controls the top heating plate
as well as the timer for length of pressing. The control panel on the right controls the
bottom heat plate only.
Left Side:
1) Controls Top Plate
2) Time of Press
Right Side:
1) Controls Bottom Plate
4
All Rights Reserved. Copyright © 2018, Rosin Tech Products
STEP 2:
ENTER SETTINGS MODE
Press the “SET” button one time. You are now in the ‘edit settings’ mode.
* TIP #2: SP = Temperature Mode
5
All Rights Reserved. Copyright © 2018, Rosin Tech Products
STEP 3:
ADJUST TEMPERATURE
●Press the up and down arrows to increase or decrease the temperature of the plates.
●Once you have found your desired temperature, press the set button to change from SP
to ST.
* TIP #3: Default setting is to Fahrenheit.
6
All Rights Reserved. Copyright © 2018, Rosin Tech Products
STEP 4:
ADJUST LENGTH OF PRESS
●Now the screen shows ST. Press the up and down arrows to increase or decrease the
timer set for each press.
●Once you have found your desired time, press the set button until you return back to
“Normal Mode”, seen below. To start the timer, press the “Timer” button on the panel.
*TIP #4: ST = Set Time of Press.
7
All Rights Reserved. Copyright © 2018, Rosin Tech Products
STEP 5:
LET PLATES HEAT UP
●Once you have found your desired time, press the set button until you return back to
“Normal Mode”, seen below.
●Now that you’ve set your temperature and length of press, its time to let both heating
plates warm up.
*TIP #5: To set the temperature on the bottom heat plate, use the right control panel and follow
the same steps. Remember length of press isn’t a factor here although you can change the
setting.
8
All Rights Reserved. Copyright © 2018, Rosin Tech Products
STEP 6:
SPEED / PRESSURE CONTROL
●The pressure control knob is located on the right side of the machine, directly above the
engage button (Fig 1).
●The pressure control knob when closed and tightened will force the heat plates to close
slower towards one another (Fig 2).
●When the pressure control knob is open and loose, the plates will close faster towards one
another (Fig 3).
9
All Rights Reserved. Copyright © 2018, Rosin Tech Products
Fig 1 Fig 2 Fig 3
STEP 7:
ENGAGE PRESS
●Two Engage buttons are located on left and right side controls and green in color (Fig 1).
●To begin the press, press both engage buttons at the same time (Fig 2).
●Plates will begin to close at desired speed set by pressure control.
Tip: If press will not engage after release emergency stop button.
10
All Rights Reserved. Copyright © 2018, Rosin Tech Products
Fig 1 Fig 2
STEP 7:
DISENGAGE PRESS
●Twist emergency stop button at any time to release heat plates located on left side
controls in red.
●Plates will separate immediately.
11
All Rights Reserved. Copyright © 2018, Rosin Tech Products
Table of contents
Other Rosin Tech Power Tools manuals
