Rossmax RA600 User manual

For after sales service, please contact Cypress Medic Sdn Bhd (www.cypressmedic.com.my)
Rossmax Thermometer RA600
Quick Guide
How to use the RA600 Infrared Ear Thermometer
1. To achieve accurate readings, make sure a new, clean probe cover is in place before each measurement
and the ear canal is clean.
a. Install the probe cover by clockwise rotating then fix it.
b. Remove the probe cover by anti-clockwise rotating then releasing it.
2. Press the “On/Off/Memory” button. The thermometer is ready for use after the ear icon is flashing and two beeps
are sounded.
3. Gently pull the ear back to straighten the ear canal and snugly position the probe into the ear canal, aiming towards
the membrane of the eardrum to obtain an accurate reading.
a. Before measurement, correct installation of the probe cover ensures accurate measurement.
b. Replace the probe cover after each use to ensure an accurate reading and avoid cross contamination.
c. This thermometer must only be used with Rossmax probe covers, other covers can lead to inaccuracy.
If running out of probe covers, please contact with the original seller or distributor for buying new
probe covers.
4. Measuring the ear temperature: Use the index finger to trigger. Press “Start” button, a long beep will be sounded
when measurement is done.
5. Power Off: Device will automatically shut off if left idle for more than 1 minute to extend buttery life. Or press
“On/Off/Memory” button for at least 3 seconds to turn the device off.
6. Fever alarm: the measuring temperature is higher than 37.5°C (99.5°F), the display will flashing and 4 short beeps
will be sounded. The measuring temperature is higher than 42.2°C (108.0°F), the display will show “Hi“and 4 short
beep will be sounded.
a. It is recommended that you measure 3 times with the same ear. If the 3 measurements are different, select
the highest temperature.
b. To avoid the risk of cross contamination, please clean the probe according to “Clean and Storage“section after
each use.

For after sales service, please contact Cypress Medic Sdn Bhd (www.cypressmedic.com.my)
Scanning Mode
If you continuously obtain different measurement results, it is recommended that you use Scanning Mode to
measure.
Measuring the ear temperature: Use the index finger to trigger, press and hold the “Start” button for 3
seconds to take measurement. During the measuring process, gently pivoting the probe side-to-side to view
the entire ear canal or in order to find the highest temperature. Release the “Start” button until hearing a
long beep sound and the measurement is completed.
Cautions
1. Besides the oral temperature, the body temperature measured by ear may be different from
measurements taken by rectal or axillary. Therefore, there is no any meaning to compare them. Take
the temperature periodically to find out the normal ear temperature reading, then use that reading as
the basis for comparison with any measurement taken when you suspect a fever.
2. Keep the unit dry and away from where it might be exposed to moisture, liquids, direct sunlight, high
temperature, high humidity, or excessive dust.
3. This device is not shock-protected. Do not drop, heavily pressure the unit or fall from high place.
4. Wipe the device clean before storing.
5. When taking the device from storage below or above 10~ 40°C (50~104°F), place it in 10~ 40°C
(50~104°F) temperature range for at least 30 minutes before use.
6. Be sure to consult a doctor if you feel that your health is in poor condition.
Cleaning and storage
The probe is the most delicate part of the thermometer. Use with care when cleaning the lens to avoid
damage.
1. Please use the cotton swab with the Alcohol to clean the lens (on the inside of the probe).
2. Allow the probe to fully dry for at least 5 minutes.
a. Please check the device if it falls and damages. If you can’t make sure of it, please send the complete
device to the nearest retailer for checking.
b. Keep the unit dry and away from any liquid and direct sunlight. The probe should not be submerging
into liquids.