rotork YT-3700 User manual

SMART POSITIONER PRODUCT MANUAL
YT-3700 / 3750
YT-3700
YT-3750
Rotork YTC Limited
VERSION 1.03

Smart Positioner
YT-3700 / 3750 Product Manual
Ver. 1.03 2
Contents
1Introduction.................................................................................................................................................5
1.1 General Information for the users.........................................................................................................5
1.2 Manufacturer Warranty.........................................................................................................................5
1.3 Explosion Proof Warning (Only for Intrinsic safety type positioners)....................................................6
2Product Description ...................................................................................................................................7
2.1 General.................................................................................................................................................7
2.2 Main Features and Functions ...............................................................................................................7
2.3 Label Description..................................................................................................................................8
2.4 Product Code..................................................................................................................................... 13
2.5 Product Specification......................................................................................................................... 14
2.6 Specification of Digital In, Digital out ................................................................................................. 15
2.7 Certifications...................................................................................................................................... 16
2.8 Parts and Assembly........................................................................................................................... 18
2.9 Product Dimension ............................................................................................................................ 20
2.9.1 YT-3700......................................................................................................................................... 20
2.9.2 YT-3750......................................................................................................................................... 20
3Installation................................................................................................................................................ 21
3.1 Safety................................................................................................................................................. 21
3.2 Tools for installation........................................................................................................................... 21
3.3 Linear positioner Installation.............................................................................................................. 22
3.3.1 Linear positioner Installation of Standard lever type...................................................................... 22
3.3.2 Safety............................................................................................................................................. 22
3.3.3 Standard lever type positioner Installation Steps .......................................................................... 23
3.4 Rotary positioner Installation ............................................................................................................. 26
3.4.1 YT-3700R / 3750R Components ................................................................................................... 26
3.4.2 Rotary Bracket Information............................................................................................................ 27
3.4.3 Rotary positioner Installation Steps............................................................................................... 28
4Connection - Air....................................................................................................................................... 29
4.1 Safety................................................................................................................................................. 29
4.2 Supply Pressure Condition ................................................................................................................ 29
4.3 Piping Condition................................................................................................................................. 29
4.4 Connection –Piping with actuator..................................................................................................... 30
4.4.1 Single acting actuator .................................................................................................................... 30
4.4.2 Double acting actuator................................................................................................................... 30
5Connection –Power................................................................................................................................ 31
5.1 Safety................................................................................................................................................. 31
5.2 Connection......................................................................................................................................... 32
5.2.1 Standard Terminals ....................................................................................................................... 32
5.2.2 Terminals with micro-limit switch option ........................................................................................ 34

Smart Positioner
YT-3700 / 3750 Product Manual
Ver. 1.03 3
5.2.3 Terminals with proximity Limit Switch option................................................................................. 35
5.3 Ground............................................................................................................................................... 35
6Adjustments............................................................................................................................................. 36
6.1 Limit Switch Adjustment..................................................................................................................... 36
6.2 A/M switch adjustment....................................................................................................................... 37
6.3 Orifice Installment.............................................................................................................................. 38
6.3.1 Plate type Orifice Installment......................................................................................................... 38
7Optional Sub-PCB Installment................................................................................................................ 39
7.1 Installation steps................................................................................................................................ 39
8Auto Calibration and PCB Operation..................................................................................................... 41
8.1 Warning.............................................................................................................................................. 41
8.2 LCD display and buttons.................................................................................................................... 41
8.2.1 LCD display and symbols .............................................................................................................. 41
8.2.2 Button and function........................................................................................................................ 42
8.3 Menu levels........................................................................................................................................ 43
8.4 RUN Mode Monitor............................................................................................................................ 44
8.5 Configuration and Operation.............................................................................................................. 45
8.6 Calibration (CALIb) ............................................................................................................................ 49
8.6.1 Acting Type (SINGLE / dOUBLE).................................................................................................. 49
8.6.2 Auto Calibration 1 (AUTO 1).......................................................................................................... 50
8.6.3 Auto Calibration 2 (AUTO 2).......................................................................................................... 50
8.6.4 Travel Zero (TVL ZERO) and Travel end (TVL ENd).................................................................... 51
8.7 Manual Operation (MAN OPER)........................................................................................................ 52
8.7.1 Manual Operation by Set position (MAN SP) ................................................................................ 52
8.7.2 Manual Operation by MV (MAN MV)............................................................................................. 53
8.8 Control Parameters (CTL PARM)...................................................................................................... 54
8.8.1 Dead Band (dEAdbANd)................................................................................................................ 54
8.8.2 Forward P parameter (KP UP) and reverse P parameter (KP dN)................................................ 55
8.8.3 Forward Integral time parameter (TI UP) and reverse Integral time parameter (TI dN)................ 55
8.8.4 Forward D parameter (Kd UP) and reverse D parameter (Kd dN)................................................ 56
8.8.5 Auto Dead band Mode (AUTO db) ................................................................................................ 56
8.8.6 Performance Mode (PER) ............................................................................................................. 57
8.9 Input Configuration(IN CFG).............................................................................................................. 58
8.9.1 Signal Direction (SIG NORM / REVS)........................................................................................... 58
8.9.2 Split Range Mode (SPLIT)............................................................................................................. 59
8.9.3 Custom Split Range Zero (CST ZERO)......................................................................................... 59
8.9.4 Custom Split Range End (CST ENd)............................................................................................. 60
8.9.5 Valve flow Characterization Curves (CHAR)................................................................................. 60
8.9.6 User Set Characterization 5 Points (U5) ....................................................................................... 61
8.9.7 User Set Characterization 21 Points (U21) ................................................................................... 62

Smart Positioner
YT-3700 / 3750 Product Manual
Ver. 1.03 4
8.9.8 Tight Shut Open (TSHUT OP)....................................................................................................... 63
8.9.9 Tight Shut Close (TSHUT CL)....................................................................................................... 64
8.9.10 Target Position Ramp Up Rate (RAMP UP) and Target Position Ramp Down Rate (RAMP dN)
65
8.9.11 Digital Input Function (dIF) ........................................................................................................ 67
8.9.12 Digital Input Logic (dI LOGIC).................................................................................................... 67
8.10 Output Configuration (OUT CFG)...................................................................................................... 68
8.10.1 Position Transmitter Direction (PTM NORM / REVS)................................................................ 68
8.10.2 Position Transmitter Zero / End (PTM ZERO / ENd)................................................................. 69
8.10.3 HART Feedback Direction (HT NORM / REVS)........................................................................ 70
8.10.4 Back Calculation (bACKCAL oFF / on)...................................................................................... 71
8.10.5 Digital Output Function (dOF).................................................................................................... 72
8.10.6 Digital Output Logic (dO LOGIC HI / Lo) ................................................................................... 73
8.10.7 Analog Output Function (AOF).................................................................................................. 74
8.10.8 Analog Output Logic (AO LOGIC Lo / HI).................................................................................. 75
8.11 Device Configuration (dEV CFG)....................................................................................................... 76
8.11.1 Action Setting (ACT).................................................................................................................. 76
8.11.2 Linear Interpolation (ITP oFF / on)............................................................................................. 77
8.11.3 Lock of Parameters (Write Protect, W UNLOCK / LOCK)......................................................... 77
8.11.4 Actual Position View Mode (View Mode, VI NORM / REVS) .................................................... 78
8.11.5 Polling address setting (POL AddR).......................................................................................... 78
8.11.6 Factory Reset (dEFAULT oFF / on)........................................................................................... 79
8.11.7 Positioner Self-Test (SELFTEST).............................................................................................. 80
8.12 Diagnosis Mode (dIAGNd)................................................................................................................. 81
8.12.1 Default Alarm Settings............................................................................................................... 81
8.12.2 Process Status (PS) .................................................................................................................. 83
8.12.3 Device Status (dS)..................................................................................................................... 84
8.12.4 View Monitoring Counts (VI CNTS)........................................................................................... 86
8.12.5 Diagnostic Limit Configuration (LIMT CFG)............................................................................... 87
8.12.6 Reset Alarm Status (RST ALRM oFF / on)................................................................................ 88
8.12.7 View Event Log (EVT LOG)....................................................................................................... 89
8.12.8 Partial Stroke Test Record (View PST Result Record, PST RSLT).......................................... 90
8.12.9 PST Configuration (PST CFG) .................................................................................................. 91
8.12.10 Run PST (PST NOW)................................................................................................................ 92
8.12.11 Periodic PST Test (PST Schedule, PST SCHd oFF / on)......................................................... 93
8.13Position information (INFO) ............................................................................................................... 94
8.14 Status and Alarm Code...................................................................................................................... 96
9Main Software Map .................................................................................................................................. 99

Smart Positioner
YT-3700 / 3750 Product Manual
Ver. 1.03 5
1 Introduction
1.1 General Information for the users
Thank you for purchasing Rotork YTC Limited products. Each product has been fully inspected after
its production to offer you the highest quality and reliable performance. Please read the product
manual carefully prior to installing and commissioning the product.
➢Installation, commissioning, and maintenance of the product may only be performed by trained
specialist personnel who have been authorized by the plant operator accordingly.
➢The manual should be provided to the end-user.
➢Factory Mutual approved Intrinsically Safe and Non-Incendive units must be Installed Per
drwg SKC_XXXXX_XXXXXX.pdf
➢CSA approved Intrinsically Safe and Non-Incendive units must be Installed Per drwg SKC-
XXXX.pdf
➢The manual can be altered or revised without any prior notice. Any changes in product’s
specification, design, and/or any components may not be printed immediately but until the
following revision of the manual.
➢When the manual refers to “Valve Zero / Zero” means the final valve position upon pneumatic
pressure has been fully exhausted from positioner’s OUT1 port. For example, the valve zero
position may differ between linear direct and reverse actions. (DA/RA)
➢The manual should not be duplicated or reproduced for any purpose without prior approval from
Rotork YTC Limited, Gimpo-si, South Korea.
➢In case of any other problems that are not stated in this manual, please make immediate contact
to Rotork YTC Limited.
➢Positioner is an accessory of the control valve, so please make sure to read the applicable
instruction manual of the control valve prior to installation and operation.
1.2 Manufacturer Warranty
➢For the safety, it is important to follow the instructions in the manual. Manufacturer will not be
responsible for any damages caused by user’s negligence.
➢Any modifications or repairs to the product may only be performed if expressed in this manual.
Injuries and physical damages caused by customer’s modifying or repairing the product without
a prior consultation with Rotork YTC Limited will not be compensated. If any alterations or
modifications are necessary, please contact Rotork YTC Limited directly.
➢The warranty period of the product is (18) months from the date of shipment unless stated
otherwise. Date of shipment can be checked by providing the LOT NO. or SERIAL NO. to us.
➢Manufacturer warranty will not cover products that have been subjected to abuse, accidents,
alterations, modifications, tampering, negligence, misuse, faulty installation, lack of reasonable
care, repair or service in any way that is not contemplated in the documentation for the product,
or if the model or serial number has been altered, tampered with, defaced or removed; damages

Smart Positioner
YT-3700 / 3750 Product Manual
Ver. 1.03 6
that occurs in shipment, due to act of God, failure due to power surge, or cosmetic damage.
Improper or incorrectly performed maintenance will void this limited warranty.
➢For detailed warranty information, please contact the corresponding local Rotork YTC Limited
office or main office in South Korea.
1.3 Explosion Proof Warning (Only for Intrinsic safety type positioners)
Please ensure the unit is being used and installed in conformity with local, regional, and national
explosion proof within the proper safety barrier environment.
➢Refer to “2.7 Certifications”
➢Explosion proof type of cables and gaskets should be used, when explosion gases are present
at the installation site.
➢Positioner has 2 ports for power connection. Explosion proof type wires and packing should be
used. Blind plug is required when any port is not being used.
➢Ring terminal with surface area of more than 1.25mm2with M4 spring washer should be used to
connect the power.
➢For external ground terminal, ring terminal with surface area of more than 5.5mm2should be
used.
➢Wiring in these applications shall utilize appropriate methods for Class I, Division 2 / Zone 2
➢Substitution of components may impair intrinsic safety.
➢Substitution of components may impair suitability for Class I, Division 2.
➢EXPLOSION HAZARD. Do not connect or disconnect wiring unless all sources of power have
been removed or the area is known to be non-hazardous.
(French) RISQUE D'EXPLOSION. Ne pas raccorder ou débrancher le câblage à moins Toutes
les sources d'énergie ont été enlevées ou la zone est connue pour être non dangereux.
➢The enclosure of model YT-3700 contains aluminum, which is considered to constitute a
potential risk of ignition when subjected to impact or friction. Care must be used during
installation in locating this equipment to prevent impact or friction
➢Some of the enclosure parts are made of non-metallic materials. To prevent the risk of
Electrostatic sparking, clean the enclosure only with a damp cloth.
➢The product must be installed in such a manner as to minimize the risk of impact or friction with
other metal surfaces.
➢For Intrinsically Safe installations, the product must be connected to suitably rated intrinsically
safe equipment, and must be installed in accordance with applicable intrinsically safe installation
standards.

Smart Positioner
YT-3700 / 3750 Product Manual
Ver. 1.03 7
2 Product Description
2.1 General
YT-3700 / 3750 series Smart Valve Positioner accurately controls valve stroke in response to an input
signal of 4~20mA from the controller. Built-in micro-processor optimizes the positioner’s performance
and provides unique functions such as Auto-Calibration, PID Control, and HART Protocol
Communications.
2.2 Main Features and Functions
➢LCD display enables users to monitor the positioner status.
➢User will easily understand the method of using 4 buttons because it work same in all versions of
firmware interfaces.
➢When unexpected situation like momentary blackout happens, our positioner boot-time only take
0.5 second and this can minimize the travel of valve which consequentially increase the safety of
system.
➢Positioner operates normally even there are sudden changes in supply pressure and / or high
vibration environment.
➢The method of Auto Calibration is very simple.
➢As an advantage of having very low air consumption, It could greatly reduce operating costs in
large-scale plants.
➢It is compatible with most of controllers.
➢Orifices can be installed even in the field to minimize the hunting occurrence and optimize
operating conditions.
➢Various information about positioner can be processed by HART communication.
➢Valve system becomes more stable by outputting analog feedback signal.
➢Different valve characteristics can be adjusted –Linear, Quick Open, Equal Percentage, and
User Set which user can make 5 or 21 points characterizations.
➢Tight Shut –Close and Shut - Open can be set.
➢PID parameters can be adjusted in the field without any additional communicator.
➢A/M switch can be used to direct supply air to the actuator or to manually operate the positioner
or valve without any signal.
➢Split range 4~12mA or 12~20mA can be set.
➢Operating temperature for positioners is -30 ~ 85℃ or -40 ~ 85℃(Please check certified
explosion proof temperature)
➢Hand calibration function can set Zero point or End point manually.
➢It has IP66 protection grade.
➢Epoxy polyester powder coating resists the corrosion process. (except YT-3750).
➢Maintenance of the positioner is easy because of modularized inner structure.
➢SIL2 certified.(For more information, see SIL Safety Instruction on homepage)

Smart Positioner
YT-3700 / 3750 Product Manual
Ver. 1.03 8
2.3 Label Description
•MODEL : Indicates the model number and additional options.
•EXPLOSION PROOF : Indicates certified explosion proof grade.
•INGRESS PROTECTION : Indicates enclosure protection grade.
•INPUT SIGNAL : Indicates input signal range.
•OPERATING TEMP. : Indicates the allowable operating temperature.
•SUPPLY PRESSURE : Indicates the supply pressure range.
•SERIAL NUMBER : Indicates unique serial number.
•YEAR.MONTH : Indicates manufactured year and month.
•INTRINSIC SAFETY / NONINCENDIVE : Indicates intrinsic safety explosion proof grade.
•AMBIENT TEMP. : Indicates the allowable ambient temperature for explosion proof.
•Ui, Ii, Pi, Ci, Li : Indicates the allowable electrical data in the certificate.
ATEX: Ui = 28 V, Ii = 93 mA, Pi = 651 mW, Ci = 0.6 nF, Li = 10 μH
FM: Ui = xx V, Ii = xx mA, Pi = xxx mW, Ci = x.xx nF, Li = xx μH
You can also see the details in the certificate.
※Precautions
Be careful not to apply volatile solvent (hardener of instant adhesive, acetone, WD-40, etc.) to
the sticker nameplate. Printed contents may be erased.
Fig. L-1: YT-3700 Non-explosion proof

Smart Positioner
YT-3700 / 3750 Product Manual
Ver. 1.03 9
Fig. L-2: YT-3700 Intrinsic safety type (ATEX, IECEx, KCs, NEPSI)
Fig. L-3: YT-3700 Intrinsic safety type (FM, CSA)
Fig. L-4: YT-3700 Non-explosion proof (TRCU)

Smart Positioner
YT-3700 / 3750 Product Manual
Ver. 1.03 10
Fig. L-5: YT-3700 Intrinsic safety type (TRCU)
Fig. L-6: YT-3700 Intrinsic safety type (INMETRO)
Fig. L-7: YT-3750 Non-explosion proof

Smart Positioner
YT-3700 / 3750 Product Manual
Ver. 1.03 11
Fig. L-8: YT-3750 Intrinsic safety type (ATEX, IECEx, KCs, NEPSI)
Fig. L-9: YT-3750 Intrinsic safety type (FM, CSA)
Fig. L-10: YT-3750 Intrinsic safety type (TRCU)

Smart Positioner
YT-3700 / 3750 Product Manual
Ver. 1.03 12
Fig. L-11: YT-3750 Intrinsic safety type (INMETRO)

Smart Positioner
YT-3700 / 3750 Product Manual
Ver. 1.03 13
2.4 Product Code
YT-3700 / 3750 1 2 3 4 5 6 7 8
1 Motion Type
L :
R :
Linear
Rotary
2 Acting type
S :
D :
Single
Double
3 Explosion Proof
N :
i :
A :
E :
Non-Explosion
ATEX, IECEx, KCs, NEPSI, INMETRO :
Ex ia IIC T5/T6 Gb, Ex ia IIIC T100℃/T85℃Db, IP66
FM & CSA :
Class I, Division 1&2 Groups ABCD T5/T6
Class II, Division 1&2 Groups EFG T100℃/T85℃; Class III
Class I, Zone 0, AEx ia IIC T5/T6,
Ex ia IIC T5/T6 Ga; Ex tb IIIC T100℃/T85℃Db
Intricsic safety for TRCU
4 Lever Type
Linear
0 :
1 :
2 :
10 ~ 40 mm (Standard type)
20 ~ 100 mm (Standard type)
90 ~ 150 mm (Standard type)
Rotary
5 :
Namur
5 Conduit - Air
Connection Type
1 :
2 :
3 :
4 :
5 :
G 1/2 –Rc 1/4
G 1/2 –1/4 NPT (YT-3750 is available for No. 2 ONLY)
G 1/2 –G 1/4
M20x1.5P –1/4 NPT
1/4 NPT –1/4 NPT
6 Communication
2 :
HART Communication
7 Option
0 :
1 :
4 :
5 :
None
+ 4 to 20 mA feedback
+ 4 to 20 mA feedback + Limit Switch Mech. (not available with NCS )
+ 4 to 20 mA feedback + Limit Switch Mech. (not available with NCS )
※DI/DO cannot be included at Limit Switch options
8 Operating Temp.
(Non-explosion proof)
S :
L :
A :
-30℃~ 85℃(-22℉~ 185℉, except TRCU explosion proof)
-40℃~ 85℃(-40℉~ 185℉)
-55℃~ 85℃(-67℉~ 185℉, only TRCU expolsion proof)

Smart Positioner
YT-3700 / 3750 Product Manual
Ver. 1.03 14
2.5 Product Specification
Model
YT-3700
YT-3750
Housing Material
Aluminum Die-casting
Stainless Steel 316
Motion Type
Linear
Rotary
Linear
Rotary
Acting Type
Single / Double
Input Signal
4~20mA DC
Minimum Current Signal
3.8mA
Supply Pressure
0.14 ~ 0.7 MPa (1.4 ~ 7 bar)
Stroke
10 ~ 150 mm
55 ~ 110°
10 ~ 150 mm
55 ~ 110°
Impedance
Max. 500Ω @ 20mA DC
Air Connection
Rc 1/4 or 1/4 NPT or G 1/4
1/4 NPT
Gauge Connection
Rc 1/8 or 1/8 NPT
1/8 NPT
Conduit Entry
G 1/2 or 1/2 NPT or M20x1.5P
G 1/2
Ingress Protection
IP66, Type 4X(FM)
Explosion Proof
1. Non-Explosion
2. ATEX, IECEx, KCs, NEPSI, TRCU, INMETRO:
Ex ia IIC T5/T6 Gb, Ex ia IIIC T100℃/T85℃Db, IP66
3. FM & CSA:
Class I, Division 1&2 Groups ABCD T5/T6
Class II, Division 1&2 Groups EFG T100℃/T85℃; Class III
Class I, Zone 0,AEx ia IIC T5/T6,
Ex ia IIC T5/T6 Ga; Ex tb IIIC T100℃/T85℃Db
Operating
Temperature
Standard Type
-30℃~ 85℃(-22℉~ 185℉, except TRCU explosion proof)
Low Temp. Type
-40℃~ 85℃(-40℉~ 185℉)
Arctic Temp. Type
-55℃~ 85℃(-67℉~ 185℉, only TRCU explosion proof)
Ambient Temperature
Of Explosion proof
T5
-40℃~ 60℃(-40℉~ 140℉)
TRCU : -55℃~ 60℃(-67℉~ 140℉)
T6
-40℃~ 40℃(-40℉~ 104℉)
TRCU : -55℃~ 40℃(-67℉~ 104℉)
Linearity
±0.5% F.S.
Hysteresis
±0.5% F.S.
Sensitivity
±0.2% F.S.
Repeatability
±0.3% F.S.
Flow Capacity
70 LPM (Sup.=0.14 MPa)
Air Consumption
Below 2 LPM (Sup.=0.14 MPa @ idle)
Output Characteristic
Linear, Quick Open, EQ%, User Set
Vibration
No Resonance up to 100Hz @ 6G
Humidity
5-95% RH @ 40℃
Communication
HART Communication (Rev. 7)
Feedback Signal (Option)
4~20mA (DC 9~28V)
Digital In/Out
Detail spec. refer to 2.6.
※N/A at Limit switch options.
Weight
2 kg (4.4 lb)
5.1 kg (11.2 lb)
Painting
Epoxy Polyester Powder Coating
-
Tested under ambient temperature of 20°C, absolute pressure of 760mmHg, and humidity of 65%.
Please contact Rotork YTC Limited for detailed testing specification.

Smart Positioner
YT-3700 / 3750 Product Manual
Ver. 1.03 15
2.6 Specification of Digital In, Digital out
1) Digital In
•Control voltage : 0 ~ 5V DC Logical switching state "0"
11 ~ 28V DC Logical switching state "1"
•Current Max. 4mA
2) Digital Out
•Supply voltage 5 ~ 28V DC
•Current < 1mA, Switching state logical "0"
•Current > 2.2mA, Switching state logical "1"

Smart Positioner
YT-3700 / 3750 Product Manual
Ver. 1.03 16
2.7 Certifications
※All certifications below are posted on Rotork YTC Limited homepage(www.ytc.co.kr).
➢KCs (Korea, Pending)
Type : Intrinsic safety
Rating : Ex ia IIC T5/T6, Ex iaD T100℃/T85℃, IP66
Certification No. : XX-KA2BO-XXXXX(YT-3700)
XX-KA2BO-XXXXX(YT-3700+LS(Dry contact))
XX-KA2BO-XXXXX(YT-3700+LS(Non-contact))
XX-KA2BO-XXXXX(YT-3750)
XX-KA2BO-XXXXX(YT-3750+LS(Dry contact))
XX-KA2BO-XXXXX(YT-3750+LS(Non-contact))
XX-KA2BO-XXXXX(YT-3703)
XX-KA2BO-XXXXX(YT-3701)
Ambient temperature : -40 ~ +60℃(T5/T100℃), -40 ~ +40℃(T6/T85℃)
➢ATEX
Type : Intrinsic safety
Rating : II 2G Ex ia IIC T5/T6 Gb, II 2D Ex ia IIIC T100℃/T85℃Db, IP6X
Certification No. : EPS 19 ATEX 1 145 X
Ambient temperature : -40 ~ +60℃(T5), -40 ~ +40℃(T6)
➢IECEx
Type : Intrinsic safety
Rating : Ex II 2G Ex ia IIC T5/T6 Gb, Ex II 2D Ex ia IIIC T100℃/T85℃Db, IP6X
Certification No. : IECEx EPS 19.0069X
Ambient temperature : -40 ~ +60℃(T5/T100℃), -40 ~ +40℃(T6/T85℃)
➢NEPSI (Pending)
Type : Intrinsic safety (Only YT-3700/3750)
Rating : Ex ia IIC T5/T6
Certification No. : GYJXX.XXXXX
➢TRCU (Pending)
Type : Intrinsic safety
Rating : 1Ex ia IIC «T6 ... T5» Gb X, Ex ia IIIC «T85 °C ... T100 °C» Db X
Certification No. : RU C-KR.MЮXX.B.XXXXX
Ambient temperature : -55 ~ +60℃(T5/T100℃), -55 ~ +40℃(T6/T85℃)
➢FM (Pending)
Rating : Class I, Div 1, Groups ABCD
Class I, Zone 0 AEx ia IIC
Class II/III, Div 1, Groups EFG
Class I, II, III, Div 2, Groups ABCDEFG
NEMA Type 4X, IP66
Certificate No.: FMXXUSXXXXX
Ambient temperature : -40 to +60℃(T5), -40 to +40℃(T6)

Smart Positioner
YT-3700 / 3750 Product Manual
Ver. 1.03 17
➢CSA (Pending)
Type : Intrinsic safety
Rating : Class I, Division 1&2 Groups ABCD T5/T6
Class II, Division 1&2 Groups EFG T100℃/T85℃
Class III
Ex ia IIC T5/T6 Ga
Ex tb IIIC T100℃/T85℃Db
IP66
Certificate No.: CSA XX.XXXXXXXX
Ambient temperature : -40 to +60℃(T5), -40 to +40℃(T6)
➢INMETRO(Brazil, Pending)
Type : Intrinsic safety
Rating : Ex ia IIC T5/T6 Gb, Ex ia IIIC T100℃/T85℃Db, IP66
Certification No. : DNV XX.XXXX X
Ambient temperature : -40 ~ +60℃(T5), -40 ~ +40℃(T6)
➢SIL2 (in a redundant structure up to SIL 3, Pending)
Intended application : Safety function is defined as to move into fail-safe-position, when
signal to positioner is interrupted.
Certification No. : XXX/V XXX.XX/XX
➢Electromagnetic Compatibility (EMC)
- EMC directive 2014/30/EC from April 2016
- EC Directive for CE conformity marking

Smart Positioner
YT-3700 / 3750 Product Manual
Ver. 1.03 18
2.8 Parts and Assembly
Fig. 2-1: Exploded view of standard type positioner
1. Base Cover 7. Base body
2. PCB Cover 8. Pilot Block
3. Main PCB 9. Auto Manual Switch
4. Torque Motor 10. Feedback Lever
5. Main Shaft(for NCS) 11. Gauge Block
6. Pilot

Smart Positioner
YT-3700 / 3750 Product Manual
Ver. 1.03 19
Fig. 2-2: Exploded view of limit switch type positioner
1. Base Cover 8. Potentiometer
2. PCB Cover 9. Base body
3. Main PCB(limit switch type) 10. Pilot Block
4. Torque Motor 11. Auto Manual Switch
5. Cam assembly 12. Feedback Lever
6. Pilot 13. Gauge Block
7. Main Shaft(potentiometer type).

Smart Positioner
YT-3700 / 3750 Product Manual
Ver. 1.03 20
2.9 Product Dimension
2.9.1 YT-3700
Fig. 2-3: YT-3700L Fig. 2-4: YT-3700R+LS
2.9.2 YT-3750
Fig. 2-5: YT-3750L Fig. 2-6: YT-3750R+LS