Royal Sovereign RSC-1653P User manual

RSC-1401CLTW /1651CLTW /1653P Laminator
OWNER'S MANUAL
Royal Sovereign International Inc.
www.royalsovereign.com
Read all instructions carefully before use.
For any Customer Support needs please choose the
Customer Support tab on www.royalsovereign.com

22
TABLE OF CONTENTS
TOPIC PAGE
1. Introduction ........................................................................................................3
2. Safety Precautions.............................................................................................. 3
3. Installation ........................................................................................................... 4
4. Included with Laminator...................................................................................... 5
5. Product Identification ...........................................................................................6
6. Control Panel ...................................................................................................... 7
7. Roller Nip Settings .............................................................................................. 8
8. Using Foot Pedal and Remote Control............................................................... 9
9. Loading Film........................................................................................................ 9
10. Threading Film
10.1. Decaling ................................................................................................. 10
10.2. Mounting ................................................................................................ 11
11. Installation of front feeder and rear rewinder options.................................... 12
12. Maintenance ................................................................................................... 13
13. Troubleshooting .............................................................................................. 13
14. Specifications.................................................................................................. 14
15. Warranty.......................................................................................................... 15

RSC-1401CLTW /RSC-1651CLTW /RSC-1653P
33
1. INTRODUCTION
2. SAFETY PRECAUTIONS
Thank you for choosing a Royal Sovereign laminator. It has been designed and
manufactured to provide years of continuous service. For complete operating and
maintenance information please read this manual thoroughly. Upon receipt of your
laminator, please inspect the box, the machine and all other contents for shipping
damage. Damage should be brought tothe immediate attention of the delivering carrier
(See page 4 for list of shipment elements).
Failure tocomply with any of the following safety procedures could result in serious injury.
Please read the instructions carefully and keep for future reference.
1. Only a licensed electrician should install wiring and outlet for the laminator.
2. Ensure the unit is plugged into a properly grounded outlet with the correct voltage.
3. Keep hands and clothing (i.e. Neckties) away from rollers. The rollers have pinch points
that can trap body parts or clothing and cause serious injury.
4. Keep flammable and wet objects away from the machine.
5. Place machine on a level surface.
6. Avoid excessive sunlight, humidity and extreme temperatures.
7. Ensure the unit is turned off, cooled, and unplugged from the outlet prior to moving and/
or repairing and/or maintenance.
8. Keep out of reach of children.
9. Only Royal Sovereign authorized maintenance and service technicians should make
repairs.
10. Do not attempt to laminate items that exceed total recommended material thickness for
the unit
11. When cleaning the machine, don't use flammable sprays or materials.
12. Do not touch the rollers when they place foreign objects inside the machine.
13. When moving the unit,don't touch the feed table.
14. If emergency happen, press emergency switch immediately.
15.Temperature of circumstance: 20
ºC ± 5 ºC ; humidity of circumstance: < 95%(20 ºC ±
5
ºC ).
16.Warning - Hazardous Moving Parts – Keep Fingers And Other Body Parts Away.

4
MODEL RSC-1401CLTW RSC-1651CLTW RSC-1653P
Power Supply
AC 100-120V or 220-240V AC 100-120V or 220-240V AC 100-120V or 220-240V
50/60HZ 50/60HZ 50/60HZ
Single Phase
4
3. INSTALLATION
Note: The laminator should be installed by a trained service technician.
Note: For proper input voltage requirements see the marking lable on the
equipment.
ELECTRICAL REQUIREMENTS
The laminator comes fully assembled, except for the stand to avoid shipping damage.
Upon arrival, thoroughly inspect the unit. It is imperative that any shipping damage is
reported and a claim is filed with the delivering carrier immediately upon receipt.
The laminator should be located in an area with adequate work space for feeding
graphics and lamination materials.
Avoid placing the laminator in a dusty area or near sources of extreme heat or cold.
Once the laminator is in place, lock the casters into position(“ON” position). Always
unlock the casters (“OFF”position) when moving to a different location.
The socket-outlet shall be installed near the equipment and shall be easily accessible.
Royal Sovereign recommends that a licensed electrician ensures proper power
installation toyour laminator in accordance with electrical codes in your area.
The laminator should have a dedicated power line.
230V UL
120V UL
220V EU
240V UK
220V AU

RSC-1401CLTW /RSC-1651CLTW /RSC-1653P
55
4.INCLUDED WITH LAMINATOR
Thoroughly inspect the parts and the unit. It is imperative that any missing parts are
reported and a claim is filed with the reseller immediately upon receipt of shipment.
Part Name
Laminator
Owner's Manual
3´´ (76mm) / 2" (57mm) Auto Grip
L-wrench (2.5/6)
Dust Cover
Spare Motor Fuse - Slow Blow fuse(50T)
(6.3A)
Spare Main Power Fuse -Time lag fuse(65TS)
(5A)
1
1
6/6
1/1
1
1
1
8
4
Quantity Picture
4-Spring Washer(¢8.5)
(Included with option only)

6
NO. PART NAME RSC-1401CLTW RSC-1651CLTW RSC-1653P
1SAFETY SENSOR
2EMERGENCY SWITCH
3FEEDTABLE
4MAIN ROLLER
5ASSEMBLY STAND
6FOOT PEDAL
7PRESSURE LEVER
8CONTROL PANEL
9SHAFT TAKE UP
6
5. PRODUCTIDENTIFICATION
1
2
3
4
5
9
7
6
8
2
2
9
O OO
O OO
O OO
O OO
O OO
O OO
O OO
O OO
O OO

RSC-1401CLTW /RSC-1651CLTW /RSC-1653P
7
6. CONTROL PANEL
When the machine is initially turned on, the LED display window will show the speed at 1.
Control Buttons
1. SPEED DISPLAY: Display’s current Speed.
2. SPEED BUTTON:Adjusting the speed of the rollers. Tochange the speed of the rollers,
press the up or down arrow button.
3. RUN:To start the rollers.
4. STOP:Tostop the rollers.
5. REV: To reverse the rollers, press and hold the REVERSE button.
7
1
2
3
4
5

88
7. ROLLER NIP SETTING
It is important to adjust the roller nip settings tothe appropriate thickness of the board
being used. Use the guide below to adjust tothe correct position.
NOTE: If you don't want to laminate,please place the pressure lever tothe "Open
position(NO.7)".
1
2
3
4
5
6
1.5mm(0.06in)
15mm(0.6in)
3mm(0.12in)
5mm(0.2in)
8mm(0.3in)
11mm(0.43in)
Laminating
NO.InchesMetric
(mm)
1 Lamination Lamination
2 0.06˝1.5
3 0.12˝3
4 0.2˝5
5 0.3˝8
6 0.43˝11
7 0.6˝15

RSC-1401CLTW /RSC-1651CLTW /RSC-1653P
99
8. USING FOOTPEDAL AND REMOTE CONTROL
USING FOOT PEDAL
Place the foot pedal on the floor in front of the
machine. Once all correct settings are displayed,
you may use the foot pedal to operate the laminator
for “Hands Free Operation.” To activate the
machine, press the foot pedal once and then release.
Repeat to stop the rollers.
9. LOADING FILM
Royal Sovereign films are wound with the adhesive side facing the inside of the roll
(adhesive in).
Loading films to upper and lower film shafts:
(See page 5 for assistance with parts identification.)
1. Adjust the auto grip tofit tothe film and tighten the
auto grip screw (Figure 1).
2. Remove the upper and lower film shafts from the
machine and load the films (Center the upper and
lower films on the shaft). Note the direction of the
adhesives on the lower and upper films
(Figure 2).
Figure 1
Figure 2

1010
10. THREADING FILM
Figure 1
Figure 2
10.1. Decaling
1. Turn the power switch on (“I” position). The Power
switch is located on the rear left side of the unit.
2. Complete the steps as in the “LOADING FILM” section
(see page 8).
3. Pull the top film down tothe bottom of the craft paper/
mounting film.
4. Align and center the craft paper/mounting film tothe
top film (Figure 1).
5. Peel the top film off (Figure 2).
PAPER BACK