Royal Sovereign Alexis 27 User manual

Alexis 27
OWNER'S MANUAL
Read all instructions carefully before use.
Royal Sovereign International Inc.
www.royalsovereign.com

2
TABLE OF CONTENTS
TOPIC PAGE
1. Introduction .......................................................................................................3
2. Package Contents .............................................................................................. 3
3. Safety Precautions.............................................................................................. 4
4. Parts.................................................................................................................... 5
5. Features Guide ................................................................................................... 6
6. Operation Instructions ......................................................................................... 9
7. Film Loading and Threading ............................................................................. 10
8. Maintenance .................................................................................................... 12
9. Trouble Shooting Guide .................................................................................... 13
10.Specification .................................................................................................... 14
11.Warranty ........................................................................................................... 15

Alexis 27
3
1. INTRODUCTION
2. PACKAGE CONTENTS
Thank you for purchasing RS Alexis 27. It has been designed and manufactured to
provide years of continuous service. For high quality lamination, please read this
instruction manual thoroughly. This manual will provide you with complete operating and
maintenance information
· Owner's Manual
· Wrench
· Dust Cover
· Silicone Elastic

4
3. SAFETY PRECAUTIONS
Failure to comply with any of the following safety procedures could result
in serious injury. Please read the instructions carefully and keep to future
reference.
1. Only a licensed electrician should install wiring and outlet for the laminator.
2. Ensure the unit is plugged into a properly grounded outlet with the correct voltage.
3. Keep hands and clothing (i.e. Neckties) away from rollers. The rollers have pinch points
that can trap body parts or clothing and cause serious injury.
4. Keep flammable and wet objects away from the machine.
5. Place machine on a level surface.
6. Avoid excessive sunlight, humidity and extreme temperatures.
7. Ensure the unit is turned off, cooled, and unplugged from the outlet prior to moving
and or repairing.
8. Keep out of reach of children.
9. Only Royal Sovereign authorized maintenance and service technicians should make
repairs.
10. Do not attempt to laminate items that exceed total recommended material thickness
for the unit.
11. When cleaning the machine, don't use flammable sprays or materials.
12. Do not touch the rollers when they are hot or place foreign objects inside the machine.
13. Do not cover the surface of the machine until the machine has completely cooled.

5
4. PARTS
1.Upper Film 2.Lower Film 3.Idle Bar
4.Hot Rollers 5.Feed Table 6.Paper Guide
7.Control Panel 8.Tension Screw 9.Power Switch
Alexis 27
①
②
③
④
⑤
⑥
⑦
⑧
⑨

6
5. FEATURES GUIDE
Run and stop the machine.
Reverse the rollers to undo jams
and correct misfed documents .
Mode: change default mode(1~4 settings).
Reduce roller speed(9~1 setting).
Increase roller speed(1~9 setting).
Reduce roller temperature(302~176 F).
Increase roller temperature(176~302 F).
Figure 1

7
Power Switch (1)- Located on the rear of
the machine. “I” (on) “0” (off). (Fig. 2)
Cross Cutter (2)- Used to cut off the
laminated web. (Fig. 2)
Main Fuse (3)- To cut off the main power
circuit. It can recover by itself.
Feed Guide (4)-The feed guide permits
alignment of the item(s) to be laminated. To
position the adjustable guide, loosen the knob,
slide it tothe desired position and tighten the
knob to secure the feed guide in place. (Fig. 3)
Safety Cover (5)- It prevents entanglement
NOTE: If the safety cover is opened, the power
tothe motor will turn off.
Film Shaft
The film shaft holds the film supply on the
machine. (Fig. 4)
Film Tension Adjustment - Allows the
operator to increase or decrease film web
tension. clockwise to increase tension and
to decrease tension turn the knob counterclockwise.
(Fig. 5)
Figure 2
Figure 3
Figure 4
Figure 5
Alexis 27
①
②
⑤
④
③

8
1. Turn the laminator ON (I) located on the rear of the machine. (Fig. 2)
2. Choose the appropriate speed (Fig.1)
3. Do not begin laminating until the blinking light is steady (approximately 8 minutes).
4. Position the item to be laminated on the feed table.
,raeppasidoteniltaehroftiaw,nrutotnigeblliwsrellorehT.nottubNURehtsserP.5
feed the item into the machine.
6. When using PET or OPP film laminate, please use a test print first to establish correct
speed and temperature for that product. Keep a distance of 15mm between prints when
running multiple prints through the laminator.
7. Stop the laminator when all of the items have completely exited the rear of the
machine.
8. Please keep the film tension controls as loose as possible but still maintaining proper
film flow over the rollers. Tighten as needed if film has slight wrinkles over the rollers.
9. If you find the temperature level is high while laminating with some films with thin
paper on the high or middle level you can try using a lower temperature level.
Repeat the above steps until all of your lamination is complete. When lamination is
completed and the machine is not in use for an extended period of time, turn the power off.
NOTE: Stand by mode and auto power off mode
- Stand by mode: If no activity is made within 30 minutes after each use the
machine will automatically switch into stand by mode. (In stand-by mode the
temperature will decrease to 80~90℃and the three film thickness setting
indicators will blink).
- Auto power off mode: If the machineisin stand by mode and no activity is
made for 60 minutes the machinewill automaticallypower off.
-If any activity is made whilein stand byor auto power off mode the machine
will return to it’s previous stage.
6. OPERATION INSTRUCTIONS
Figure 6
Emergency Switch (6) - To stop the machine
in a emergency situation. (Fig. 6)
⑥

9
Figure 8
Figure 9
7. FILM LOADING & THREADING
Figure 7
1. Slightly slide the shaft to the right and pull it out
from the machine. (Fig. 8)
2. Set the rubber “O” ring to a suitable location
base on the width of the file, make sure they are
in the same location for both shaft.
Alexis 27

10
3. Insert shaft into the right end of the film core.
For film with poly-in (adhesive side is inside
the web), make sure the adhesive side is
facing upward. (Fig. 10)
Figure 10
4. Carefully return the film shaft back into place.