Royal Sovereign RSL2701S User manual

RSL-2701U (for CANADA MODEL)
RSL-2701S (for USA MODEL )
OWNER'S MANUAL
Read all instructions carefully before use.
For any Customer Support needs please choose the
Customer Support tab on www.royalsovereign.com
Royal Sovereign International Inc.
www.royalsovereign.com

2
TABLE OF CONTENTS
TOPIC PAGE
1. Introduction ..................................................................................................................................................... 3
2. Package Contents............................................................................................................................................. 3
3. Safety Precautions............................................................................................................................................ 4
4. Parts ................................................................................................................................................................. 5
5. Control Panel .................................................................................................................................................... 6
6. Features Guide.................................................................................................................................................. 8
7. Film Loading and Threading ............................................................................................................................ 9
8. Operation Instructions.................................................................................................................................... 13
9. Maintenance ................................................................................................................................................. 13
10. Trouble Shooting Guide................................................................................................................................ 14
11.Specification .................................................................................................................................................. 15
12.Warranty ........................................................................................................................................................ 16

TABLE TOP LAMINATOR
3
1. INTRODUCTION
2. PACKAGE CONTENTS
Thank you for purchasing the Table Top Laminator. It has been designed and manufactured to provide years of
continuous service. For high quality lamination, please read this instruction manual thoroughly. This manual will provide
you with complete operating and maintenance information.
Film leader board Manual Core 4EA Dust cover
Fuse
Sample roll film 2EA
Core bolt 4EA

4
3. SAFETY PRECAUTIONS
Failure to comply with any of the following safety procedures could result in serious injury.
Please read the instructions carefully and keep for future reference.
1. Only a licensed electrician should install wiring and outlet for the laminator.
2. Ensure the unit is plugged into a properly grounded outlet with the correct voltage.
3. Keep hands and clothing (i.e. Neckties) away from rollers.The rollers have pinch points that can trap body parts
or
clothing and cause serious injury.
4. Keep flammable and wet objects away from the machine.
5. Place machine on a level surface.
6. Avoid excessive sunlight, humidity and extreme temperatures.
7. Ensure the unit is turned off, cooled, and unplugged from the outlet prior to moving and/or repairing.
8. Keep out of reach of children.
9. Only authorized maintenance and service technicians should make repairs.
10. Do not attempt to laminate items that exceed total recommended material thickness for the unit
11. When cleaning the machine, don't use flammable sprays or materials.
12. Do not touch the rollers when hot.
Do not place any foreign obects inside the laminator.
13. Do not cover the surface of the machine until the machine has completely cooled.
14. You can laminate by single film when the switch in the left cover is “O”.
(Insure the machine drastically cold, press the button in the left cover be “ O ”, then you can laminate by single
side. It is a damage for the paper to laminate by single side while the rollers up and low are heating all together.)
- Model applies RSL-2701S only for USA.

TABLE TOP LAMINATOR
5
4. PARTS
1. Upper Film 2. Lower Film 3. Idle Bar
4. Hot Rollers 5. Feed Table 6. Paper Guide
7. Control Panel 8. Tension Knob 9. Power Switch
*10. (2701S model only) Single/Double Laminating Switch “O” (on) “I” (off).
* For Single-side Laminating.
10

6
5. CONTROL PANEL
Film Application Temperature
210~230 ˚F
Film Application Temperature
230 ~270 ˚F
Film Application Temperature
270 ~310 ˚F
210 ~230 ˚F
230 ~270 ˚F
270 ~310 ˚F
25 - 38 mic
50 - 75 mic
100 - 125 mic
210-230 F
230-270 F
270-310 F
1 - 1.5 mil
2 - 4 mil
5 mil
25-38 mic
50-100 mic
125 mic
Run and stop the machine
RUN/STOP
Reverse the rollers to undo jams and correct
misfed documents
REVERSE
Reduce roller speed
(1~10 speed settings)
DOWN
Increase roller speed
(1~10 speed settings)
UP
RSL-2701U

TABLE TOP LAMINATOR
7
Film Application Thickness
125mic(100~125mic)
125mic
* (100~125mic)
Film Application Thickness
50~100mic(50~75mic)
50~100mic
* (50~75mic)
Film Application Thickness
25~38mic(25~38mic)
25~38mic
* (25~38mic)
Run and stop the machine
RUN/STOP
Reverse the rollers to undo jams and correct
misfed documents
REVERSE
Reduce roller speed
(1~10 speed settings)
UP
Increase roller speed
(1~10 speed settings)
DOWN
* For Single side Laminating.
25 - 38 mic
50 - 75 mic
100 - 125 mic
210-230 F
230-270 F
270-310 F
1 - 1.5 mil
2 - 4 mil
5 mil
25-38 mic
50-100 mic
125 mic
RSL-2701S

8
Power Switch 1
Located on the rear of the machine. “I” (on) “0” (off). (Fig. 2)
Cross Cutter 2
Used to cut off the laminated web. (Fig. 2)
Feed Guide 3
The feed guide permits alignment of the item(s) to be laminated.
To position the adjustable guide, loosen the knob, slide it to the
desired position and tighten the knob to secure the feed guide in
place. (Fig. 3)
Safety Cover 4
Cover + Protect the hot rollers.
NOTE: If the safety cover is opened, this rollers stop turning.
Film Shaft and Locking Core Adapter 5
The film shaft holds the film supply on the machine. The locking
core holds and locks the film on the shaft to prevent shifting. (Fig.
4)
Film Tension Adjustment 6
Allows the operator to increase or decrease roll film tension. To
increase the tension turn the knob clockwise and to decrease
tension turn the knob counterclockwise. (Fig. 5)
NOTE: - Excess tension on the top roll feed will cause upward
curl.
- Excess tension on the botton roll feed will cause
downward
curl.
- Tension should be adjusted until the laminated materials
exit flat.
Figure 2
Figure 3
Figure 4
Figure 5
6. FEATURES GUIDE
5
6

TABLE TOP LAMINATOR
9
Figure 7
Figure 8
7. FILM LOADING & THREADING
Figure 6
1. Slightly slide the upper film shaft to the right and pull it out from
the machine. (Fig. 7)
2. Take both lock core adapters off from the shaft. (Fig. 8)

10
3. Insert one of the core adapters into the right end of the film
core. For film with poly-in (adhesive side is inside the web), make
sure the adhesive side is facing upward. (Fig. 9)
Figure 9
4. Insert the film shaft into the roll of film from the right side with
the copper end last.
Align and insert the core adapter on the left end of the film
core. (Fig. 10)
Figure 10
5. Center the film on the shaft and lock it in place with the
locking core adapters. (Fig. 11)
6. Carefully return the film shaft back into place. (Fig. 12)
Figure 11
Figure 12