Royal Sovereign 1650C User manual

Royal Sovereign LAMINATORS
OWNER'S MANUAL
RSC-1650H/1650C
PLEASE READ AND SAVE INSTRUCTIONS
- 1 -

TOPICS PAGE
INSTRUCTION --------------------------------------------------------------
-
3
SAFETY PRECAUTIONS -----------------------------------------------------
-
3
CHARACTERISTICS ----------------------------------------------------------
-
4
SPECIFICATIONS --------------------------------------------------------------
-
4
NAMES OF MAJOR PARTS OF MACHINE-----------------------------------
-
5
SETTING UP FILM ------------------------------------------------------------
-
6
HANGING FILM ---------------------------------------------------------------- 7
CONTROL OF ROLLER PRESSURE ---------------------------------------
-
8
INSTRUCTIONS FOR CONTROL PANEL ---------------------------------
-
9
1.FUNCTIONS OF CONTROL PANEL ---------------------------------
-
10
2.HOW TO USE BUTTONS ----------------------------------------------
-
10
LAMINATING STEPS ------------------------------------------------------------ 11
METHOD FOR USING CUTTER -----------------------------------------------
-
12
1.CROSS CUTTER -----------------------------------------------------------
-
12
IMPORTANT SAFETY CONCERNS ---------------------------------------- 13
MAINTENANCE --------------------------------------------------------------------
-
13
IT'S NOT OUT OF ORDER ----------------------------------------------------
-
14
ASSEMBLY PARTS -------------------------------------------------------------
-
14
WARRANTY ----------------------------------------------------------------------- 15
TABLE OF CONTENTS
- 2 -

Thank you for purchasing a Royal Sovereign Roll Laminator. It has been designed and
manufactured to provide years of continuous service in the professional environment.
To insure high quality lamination, please read this instruction manual thoroughly. This
manual will provide you with complete operating and maintenance information.
The safet
y
recommendations outlined in this section are to be read, understood and
followed before operating machine.keep this information for future refrence. Failure to.
com
p
l
y
an
y
of the followin
g
safet
y
p
rocedures could result in serious
p
ersonal in
j
ur
y
.
1. To prevent the possibility of electrical shock, do not immerse machine in water or
permit liquids to spill inside.
2. Do not allow articles of clothing (neckties, scarves, papers, etc.) near front or rear
machine openings as they could get caught by rollers and be pulled inside, causing
personal injury.
3. Do not insert sharp objects into front or rear machine openings.Do not place anything
in feed tray openings of machine other than appropriate laminating materials or pouches
4. Do not attempt to laminate items that exceed total recommended material thickness.
5. Do not operate machine for any other purposes than its intended use.
6. Do not operate machine if electrical plug or power cord is damaged.
7. Turn off the power when unattended or not in use. Unplug machine before moving it or
when it is not in use for an extended period of time.
8. This machine is intended for indoor use only.
9. Do not alter or extend electric plug. Plug is configured for appropriate electrical supply.
10. The socket-outlet shall be installed mear the equipment and shall be easily accessible.
SAFETY PRECAUTIONS
INSTRUCTION
- 3 -

RS Roll Laminator Line is advanced laminators with time transcendental desi
g
n, utilizin
g
the
latest in laminatin
g
technolo
gy
.
It is desi
g
ned for
y
ou to set temperature and speed as necessar
y
. Also
y
ou can laminate
an
y
thin
g
at hi
g
h speed,re
g
ardless of thickness of material and t
y
pe of film.It is also desi
g
ned
for convenient use by anyone through the simple procedure of adjusting film tension in
accordance with the thickness of film and materials to be laminated.
—
Laminating Length Measurement
yes
no
Remote switch
9 step (digital)
DC Geared Motor
2 Roller
Laminating Paper Counting
Gross Weight
no
Dimension(W×D×H,mm）
Unit Weight
Gross Demension(W×D×H,mm）
1960×650×1210（77.2“×25.6”×47.4“）
230Kg(500ibs)
2100×875×1250（82.7“×34.1”×49.2“）
300Kg(660ibs)
Power auto-off
no
no
Foot switch yes
Stand-by mode
Mount Lamination
Reverse
yes(15mm)
yes
Hot Lamination
Photo Lamination yes
Transport Type
Cooling System
no
no
Speed Control
Driving Motor
Ready time(min) 10
Heating Method Warm Roller
Temp` Select
Temp`Control
9 step
digital
120V/60Hz
Power Consumption(Watts) 1700
Max. Laminating Width(mm) 1650(65") 1650(65")
Power Supply 120V/60Hz
Laminating Thickness(micron)
Laminating Speed(mm/min)
25,50,75,80,100,…
5000(16.4ft/min)
RSC-1650C
no
100
Description RSC-1650H
SPECIFICATIONS
CHARACTERISTIC
- 4 -

NO
1
2
3
4
5
6
7
8
9
10
11
12
13
○
TAKE-UP BOBBIN
IDLE BAR
HOT ROLLER
TABLE-FRONT
UPPER ROLLER
○
○
X
TAKE-UP SWITCH
○
○
PART NAME
FRAME-GUIDE,PAPER
RSC-1650H RSC-1650H
NAMES OF MAJOR PARTS OF MACHINE
CONTROL PANEL
○
FOOT SWITCH
○
ASS'Y-STAND
PRESSURE LEVER
TENSION CONTROL KNOB
SAFETY COVER
○
REMOCON SWITCH ○
○
○
○
6
11 32
4
9
10
5
7
1
8
12
13
- 5 -

1. Set the glossy side of upper/lower film to face the heat.
( Glossy side is PET film and matte side is thermal polymer laminating film.)
2. Like picture 1, insert core into the left side of upper/lower film shaft.
3. Like picture 2 and 3, insert core into the right side of upper/lower film.
4. Like picture 4 and 5, adhere core closely.
(Make the right/left direction of fixing screw consistent.)
5. Locate film in the middle, and then fasten core fixing screw.
SETTING UP FILM
주 름 방 지 부
열 판
주 름 방 지 부
열 판
표 시 창
L
C
D
버 튼 부
COLD FILM
PAPER BAC
K
- 6 -

1. Set up cold film below the upper bar of the machine.
(Set the same as methord of the HOT film for protect paper of lower part)
2. Set the pressure lever to the 15mm, open mode.
3. Insert a piece of wide cardboard (guiding paper/carrier) between the rollers.
4. Pull the film from the upper roller passing over the upper idle bar to the upper roller and put it
on the upper roller.
5. Put the paper back of the film to the bobbin at take-up bar to rewind the paper back.
6. Allow some of the film with melted resin to stick to the Guiding Paper.
7. Place the film from lower shaft beneath the film from the upper roller which is already meiting.
and unwind films of both rollers 30~40cm(1~1.3ft) for loosing the tension.
8. Set the pressure lever to the 1mm.
9. Set speed at 1 and press the RUN button. The films will be fed into the machine and will come
out from the rear site of machine.
10. Check the status of lamination and place the pressure lever at lamination mode.
HANGING FILM
TAKE UP DEVICE
PAPER BACK
COLD FILM
UPPER IDLE BAR
LOWER IDLE BAR
HOT ROLLER
PAPER BACK
- 7 -

1. For setting, pull the pressure lever out and turn the lever to following the indication
2. OPEN/15mm(Board) : For laminating 15mm thick board (RSC-1650H/1650C)
3. 10~13mm(Board) : For laminating 10~13mm thick board
4. 5~7mm(Board) : For laminating 5~7mm thick board
5. 1mm(Hard Board) : For laminating 1mm thick board
6. Laminating : For laminating 32~250micron thick film
CONTROL OF ROLLER PRESSURE
***Methods of controlling pressure of the roller**
- 8 -

We designed this machine standing by user’s convenience. You can manipulate speed and
temperature .
***Terms***
INSTRUCTIONS FOR CONTROL PANEL
6 1
4
2
6
2
1
3
3
5
- 9 -

1. FUNCTIONS OF CONTROL PANEL
RUN/STOP BUTTON : Run or stop the rollers
SPEED BUTTON : Increase or decrease speed
LED OF SPEED : Display or speed
LED OF TEMP. : Display temperature
TEMP.BUTTON : Increase or decrease temperature
REVERSE BUTTON : To make the rollers run backward
2.HOW TO USE BUTTONS
Push the button in order to run rollers and push
button to stop it.
SPEED BUTTON
Push the SPEED button to increase the speed,push the speed
button to decrease the speed.
TEMP. BUTTON
Push the TEMP. button to increase the temperature,push the
TEMP. button to decrease.
REVERSE BUTTON
Stay pressing REVERSE button to have . The roller run backward.
RUN / STOP BUTTON
1
2
3
4
5
6
1
2
5
6
RUN
REV
STOP
- 10 -

1. Put cold roll film on upper bar.(Set the same as methord of the HOT film for protect paper of lower
part)
2. Pull COLD film, and fix it so that backside protecting paper can be wound on take-up mandrel
clockwise. (Revolve core to make protectingpaper tight a little bit.)
3. Set pressure lever at the proper position following to your lamination condition.
4. After pressing the RUN/STOP button choose and set proper speed by using the SPEED
button or .
5. Turn on the take up device and set the proper film tension by pressing the RUN/STOP button.
Lower tension would make better operation.
10. Set pressure lever at the Hard board/15mm mode.
11. Turn off the power switch.
1. Set up the protection paper. Otherwise, glue form the film will be stuck on the face of roller
and it can be seriously damaged.
2. Turn the switch RUN/STOP and “Take up motor” at the same time.
*** Reference ***
LAMINATING STEPS
- 11 -

**Cross Cutter**
1. It is on the back side of the machine.
2. After lamination, move cutter to a point about 1/3 of
the width of lamination.
3. Grasp film with one hand and press the cutter, cutter
downward and slide it to the direction intending to
cut with another hand.
4.Press the cutter and slide it the other way.
METHOD FOR USING CUTTER
- 12 -

1.Please be cautious that neck tie, necklace, long hair, clothes are kept well away while
operation.
2.Prevent children from accessing the machine Extreme Heat Will Cause Injury
3.Place the machines on the plated place in order to prevent the machine from damage.
4.Make certain that the machine is connecterd to an ade
q
uate
p
ower souce.
5.Do not use any other purposes other than Lamination.
1.Do not allow the machine to run with only one roll of film installed. The melted resin will
adhere to one roller and ruin future laminations.
2.The width of film should be bigger than the material, and Width of upper side and lower
side of film should be same in order not to allow melted resin to adhere to the rollers.
3.Be sure to adjust the film tension while in operation. If the tension is too tight, it could
cause the film to stretch.
4.After work, you should clean the resin from the rollers before beginning the next operation
5.Please check the lubricant after long operation or you do not use for a long time.
6.Check the chain linking each gear is not loosened.The limit tension allowed is 3mm.
IMPORTANT SAFETY CONCERNS
MAINTENANCE
- 13 -

CHECK POINT
*Rollers do not operate 1. Check the power cord.
after press RUN button
2. Check if the switch is on.
3. Check if the emergency switch
is off.
4. Check the s/w of safety cover is right.
*Wrinkled lamination 1. Adjust film tension.
result
6
BOLT CORE
8
Washer(Φ8)
6
Bolt(M8X12)
1. Power cord may not be plugged
in.
2. Power switch is at OFF mode.
3. Emergency switch may be at
1
1
Core(76mm)
FUSE(50T)
(AC250V 6.3A)
FUSE(65TS)
(AC250V 20A)
10
MODEL PART NAME
ASSEMBLY PARTS
4. The safety cover is opened.
1. Film tension is not proper, too
tight.
MODEL
It's not out of order
CauseSymptom
ON mode.
EAEA
PART NAME
RSC-1650H
RSC-1650C
RSC-1650H
RSC-1650C
- 14 -

1. For six month from the date of purchase, Royal Sovereign International Corporation or its authorized
service center will repair this product free of charge if it is defective in material or workmanship.
2. This Limited Warranty does not include cleaning, or damage caused by accident, neglect, misuse or
improper installation, operation or external scratch, any damage caused from service, maintenance,
modifications or tampering by anyone other than a Sovereign authorized service representative, or
damage caused by a natural calamity such as fire or earthquake and etc...
3. Customers will bear the expense of Transportation fee and delivery fee of the damaged machine.
WARRANTY
- 15 -