Royalcraft Faro Black User manual

Produced in China for A Mir & Co., Ltd.
© A Mir & Co., Ltd. 2 / 10
www.royalcraft.co.uk
Before you start
Warnings
IMPORTANT, RETAIN FOR FUTURE
REFERENCE
READ CAREFULLY
See enclosed instructions for safety and care
information.
Failure to follow the warnings could result in serious
injury.
Handle heavy parts with care.
Thisproduct is intended for Domestic Use only.
This product should only be used on firm, level
ground.
Ensure the product is always placed on level
ground.
Furniture can be dangerous if used incorrectly or
maintained poorly. Keep your furniture in a good
condition at all times. No liability will be accepted for
damage or injury caused by failure to follow the care
and maintenance guidelines.
Dos
Unwrap all packaging materials and place the
components on suitable surface to prevent
scratching your product.
We recommend the use of furniture covers to protect
your product when not in use.
Cushions should be cleaned following the care
instruction on the label.
If the set is stored outside then we recommend that
cushions are brought inside for storage and
protection.
To clean the product, a pressure washer or jet wash
on a wide spray can be used at a minimum distance
of 1m from the product. Do not aim thisdirectly at
the joints of the furniture. Alternatively it can simply
be wiped down by hand with a damp sponge and a
weak solution of soap and water.
We would recommend lifting the products to move the
items instead of dragging them which may cause some
damage to either the product or the area in which you
choose to use them.
Don’ts
Never drag furniture when moving it, always lift it.
Never tilt the product use.
Do not stand or climb onto the product.
Do not sit or lean onto the arms/rims of this product.
Never use scourers, abrasives or chemical cleaner.
Number of people required for assembly
Two people
Time to assemble
30 Minutes
Tools required
(Rubber Hammer may be required, not provided)
Faro Black Storage Bench
Assembly Instructions

Produced in China for A Mir & Co., Ltd.
© A Mir & Co., Ltd. 3 / 10
www.royalcraft.co.uk
Components, fixtures & fittings (not actual size)
Parts List
Part
No. Diagram Qty. Part No. Diagram Qty.
RS
Right Leg
1 PC LS
Left Leg
1 PC
D
Box Bottom Panel
2 PCS R
Box Rear Panel
2 PCS
F
Box Front Panel
2 PCS H
Connecting Bar for
Backrest
2 PCS
BC
Front Panel for Backrest
2 PCS B
Rear Panel for
Backrest
2 PCS
mm
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
190
200
210
220
0
Faro Black Storage Bench
Assembly Instructions

Produced in China for A Mir & Co., Ltd.
© A Mir & Co., Ltd. 4 / 10
www.royalcraft.co.uk
I
Seat Panel
2 PCS ML3
Connecting Bar for
Seat Panel
1 PC
ML2
Middle Leg Backrest Pole
1 PC ML1
Middle Leg
1 PC
M
Nut
1 PC N
Bolt
23 PCS
O
Cap
2 PCS P
Spanner
1 PC
Step by step assembly instructions
Faro Black Storage Bench
Assembly Instructions

Produced in China for A Mir & Co., Ltd.
© A Mir & Co., Ltd. 5 / 10
www.royalcraft.co.uk
Step One
Attach Part (ML2) to Part (ML1).
Step Two
Attach the Box Bottom Panels (D) to the Part (ML2) & (ML1).
ML2 ML1
ML2D
D
ML1
Faro Black Storage Bench
Assembly Instructions

Produced in China for A Mir & Co., Ltd.
© A Mir & Co., Ltd. 6 / 10
www.royalcraft.co.uk
Step Three
Attach Box Rear Panel (R) to each other.
Step Four
Attach Box Rear Panel (R) to the Part (ML2) and (ML1) using Bolts (N).
2 Bolts are used in this Step.
R
RML2
D
D
ML1
N
ML2
PR
Faro Black Storage Bench
Assembly Instructions

Produced in China for A Mir & Co., Ltd.
© A Mir & Co., Ltd. 7 / 10
www.royalcraft.co.uk
Step Five
Attach Box Front Panel (F) to each other.
Step Six
Attach Box Front Panel (F) to the Part (ML1) and (D) using Bolts (N).
2 Bolts are used in this Step.
F
F
ML1 DN
P
Faro Black Storage Bench
Assembly Instructions

Produced in China for A Mir & Co., Ltd.
© A Mir & Co., Ltd. 8 / 10
www.royalcraft.co.uk
Step Seven
Attach Connecting Bar for Backrest (H) to the assembled Parts.
Step Eight
Attach Front Panel for Backrest (BC) to the assembled Parts using Nut (M) and Bolts (N).
7 Bolts are used in this Step.
F
BC
N
NM M
Faro Black Storage Bench
Assembly Instructions

Produced in China for A Mir & Co., Ltd.
© A Mir & Co., Ltd. 9 / 10
www.royalcraft.co.uk
Step Nine
Attach Right Leg (RS) to the assembled Parts using Bolts (N).
Attach Left Leg (LS) to the assembled Parts using Bolts (N).
12 Bolts are used in this Step.
Step Ten
Attach Rear Panel for the Backrest (B) to the assembled Parts.
N
RS
N
LS
B
Faro Black Storage Bench
Assembly Instructions

Produced in China for A Mir & Co., Ltd.
© A Mir & Co., Ltd. 10 / 10
www.royalcraft.co.uk
Step Eleven
Attach Seat Panel (I) to Connecting Bar for Seat Panel (ML3).
Step Twelve
Place the Seat Panels (I) onto the assembled parts.
Plug in the Caps (O).
Your Storage Bench is ready for use.
Never tilt the products during use.
Ensure the product is always placed firmly on the ground.
PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE
I
ML3
I
O
Faro Black Storage Bench
Assembly Instructions