Royalcraft NEVADA CUBE CHAIR User manual

Produced in China for A. Mir & Co., Ltd.
© A. Mir & Co., Ltd. 2 / 6
www.ro
y
alcraft.co.uk
Before you start
Warnings
Two People
Time to assemble
10 minutes per chair
Tools required
NEVADA CUBE CHAIR
Assembly Instructions
IMPORTANT, RETAIN FOR FUTURE REFERENCE
READ CAREFULLY
See enclosed instructions for assembly, safety and care
information.
Failure to follow the warnings could result in serious injury.
Handle heavy parts with care.
Ensure that this product is fully assembled as illustrated before use.
This product should only be used on firm, level ground.
Keep small parts out of reach of children.
Do not stand or climb onto this product.
This product is intended for domestic use only.
Ensure the product is always placed on level ground.
Furniture can be dangerous if incorrectly used. No liability will be
accepted for damage or injury caused by incorrect use of this
product.
Dos
When you are ready to start, make sure that you have the right
tools, plenty of space and a clean, dry area for assembly.
Unwrap all packaging materials and place the components on a
suitable surface to prevent scratching your product.
Check the pack and make sure you have all parts listed. In the
event of problems or missing parts, please contact the seller.
Check all screws and bolts are tightened and inspect regularly.
Store all cushions indoors after use as they are not waterproof.
This product is suitable for all year outdoor use. However, to
prolong its life we recommend that during severe weather
conditions, including high winds, rain, hail, thunderstorms, extreme
heat and cold temperatures, the product should be stored inside in
a cool, dry place.
To best preserve the synthetic rattan, please use a protective
cover when your furniture is not in use. We would also recommend
using a gazebo or parasol over your furniture during the summer
period and prolonged sunny spells. This will help prevent harmful
UV rays from damaging and discolouring the material.
Ensure that the product is clean and dry before storage.
Clean your product with a sponge and warm soapy water then
wipe with a clean, dry cloth.
Cushions should be cleaned following the care instruction on
the label.
Where instructions as to the; storage, commissioning, installation,
use and maintenance of the goods or (if there is none) good trade
practice are not followed and a defect arises this will void the
12 month manufacturer's guarantee on the product.
Don’ts
Never tilt the chair during use.
Do not stand or climb onto the product.
Do not use power tools to construct this product.
Do not sit or lean onto the arms of this product.
Do not use this product if parts are missing, damaged or worn.
Do not use scourers, abrasives, washing powders, chemical
cleaners or any other substances containing abrasives since
these substances can damage the product.
Do not use this product as a ladder as this could lead to the
product becoming unbalanced and overturning.
Do not place very hot or very cold items on the product surface.
Never drag furniture when moving it, always lift it.
Number of people required for assembly
Tips:
It is best not to fully tighten the nuts and
bolts until they are all correctly located.
Only carefully tighten them when you
are satisfied with the alignment of all
components.
Be careful not to overtighten.

Produced in China for A. Mir & Co., Ltd.
© A. Mir & Co., Ltd. 3 / 6
www.ro
y
alcraft.co.uk
Components, fixtures & fittings (not actual size)
Parts List
Part
No. Diagram Qty. Part No. Diagram Qty.
A
Back Panel
4 PCS B
Foldable Backrest
4 PCS
C
Left Armrest/Leg
4 PCS D
Right Armrest/Leg
4 PCS
E
Seat Panel
4 PCS F
Cushion
4 PCS
W35
M6*35mm Bolt
36 PCS W50
M6*50mm Bolt
8 PCS
F1
Plastic Spacer
8 PCS F2
Bolt Head Cap
44 PCS
mm
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
190
200
210
220
0
NEVADA CUBE CHAIR
Assembly Instructions

Produced in China for A. Mir & Co., Ltd.
© A. Mir & Co., Ltd. 4 / 6
www.ro
y
alcraft.co.uk
F3
Flat Washer
44 PCS F4
Spring Washer
44 PCS
S1
Spanner
1 PC
Please note the diagram is for reference only, it may not fully represent the
actual appearance of the parts.
The quantity marked is for 4 PCS Chairs.
Bolt Head Caps can only be attached when all Bolts are tightened with
Step by step assembly instructions
Step One
Attach Backrest (A) with Left Armrest/Leg(C) & Right Armrest/Leg (D) together using
Flat Washers (F3), Spring Washers (F4), Bolts (W35), Bolts (W50) and Bolt Head Caps (F2).
Please note the Longer Bolts (W50)
should be used on the top side.
W50 F4 F3 F2
W35
F4
F3
F2
AC
D
Spanner (S1).
NEVADA CUBE CHAIR
Assembly Instructions

Produced in China for A. Mir & Co., Ltd.
© A. Mir & Co., Ltd. 5 / 6
www.ro
y
alcraft.co.uk
Step Two
Attach Seat Panel (E) to the above partly-assembled parts using Flat Washers (F3),
Spring Washers (F4), Bolts (W35) and Bolt Head Caps (F2).
Step Three
Attach Foldable Backrest (B) to the above partly-assembled parts using Plastic Washer (F1),
Flat Washers (F3), Spring Washers (F4), Bolts (W35) and Bolt Head Caps (F2).
Please note the Plastic Washer (F1)
is placed between the Parts (B)
and (C or D).
W35 F4 F3
F2
W35 F4 F3
F2
E
W35 F4 F3
F2
F1
B
D
C
NEVADA CUBE CHAIR
Assembly Instructions

Produced in China for A. Mir & Co., Ltd.
© A. Mir & Co., Ltd. 6 / 6
www.ro
y
alcraft.co.uk
Step Four
Place the Seat Cushion (F) onto the Seat Panel (E).
Your chair is now ready for use.
Never tilt the Chair during use.
Ensure the product is always placed firmly
on the ground.
PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE
F
NEVADA CUBE CHAIR
Assembly Instructions