Royalcraft Metal Planter Stand User manual

Metal Planter Stand
Assembly Instructions
Produced in China for A. Mir & Co., Ltd.
© A. Mir & Co., Ltd.  1 / 4

www.ro
y
alcraft.co.uk
Product size:
W60*D42*H91cm
This product is manufactured from mild steel coated with a weather resistant paint. Steel has a
natural tendency to rust over time and, whilst we expect you to be able to enjoy your furniture
for many years to come, we recommend that you check the product from time to time for signs
of paint damage and/ or rust. If the paint should become damaged, or if rust begins to form,
you should clean the affected area and apply a suitable “thinners based” touch-up paint. Such
paints are readily available for all good hardware and DIY stores.”
This product is for Domestic Use only!
IMPORTANT, RETAIN FOR FUTURE REFERENCE
READ CAREFULLY

Metal Planter Stand
Assembly Instructions
Produced in China for A. Mir & Co., Ltd.
© A. Mir & Co., Ltd.  2 / 4

www.ro
y
alcraft.co.uk
Before you start
Warnings
IMPORTANT, RETAIN FOR FUTURE REFERENCE
READ CAREFULLY
See enclosed instructions for assembly, safety and care
information.
Failure to follow the warnings could result in serious injury.
Handle heavy parts with care.
Ensure that this product is fully assembled as illustrated before
use.
This product should only be used on firm, level ground.
Keep small parts out of reach of children.
Ensure the product is always placed on level ground.
Furniture can be dangerous if incorrectly used. No liability will be
accepted for damage or injury caused by incorrect use of this
product.
Take care when opening and folding the furniture. Keep your
hands away from moving parts in order to prevent trapping your
fingers. Children should not open or close the furniture.
Please take care when handling or moving the product as
careless handling may cause damage or injury.
Dos
When you are ready to start, make sure that you have the right
tools, plenty of space and a clean, dry area for assembly.
Unwrap all packaging materials and place the components on
suitable surface to prevent scratching your product.
Check the pack and make sure you have all of the parts listed.
Wash the frame with a mild soap and water only. Rinse and dry
thoroughly.
To extend the product life and appearance it is advisable to store
the furniture in a cool dry place over winter.
Ensure that the furniture is clean and completely dry before putting
in to storage.
In the event of the surface paint chipping or scratching, the easiest
way to treat the problem is to treat with a spray paint/aerosol
lacquer spray, equivalent to the colour of the furniture. This will
prevent the metal from being exposed, preventing it from further
deterioration.
Don’ts
Do not use a metal brush when removing dirt from this item, as it
will strip the paint off leaving the surface open to corrosion.
Do NOT place very HEAVY ITEMS on surface(s).
Do not use this product if parts are missing, damaged or worn.
Never use scourers, abrasives or chemical cleaner.
Never drag furniture when moving it, always lift it.
Do NOT sit or stand upon this product.
Do NOT use the chair as a ladder.
Number of people required for assembly
Two People
Time to assemble
20 minutes
Tools required
Tips:
It is best not to fully tighten the nuts and
bolts until they are all correctly located.
Only carefully tighten them when you are
satisfied with the alignment of all
components.
Be careful not to overtighten.
Special Warning:
This product should NOT be used by
Children and Kids!
Load limit is 10 kg per tray. Don’t
place goods near the tray rim.
This Planter Stand should be stood
close to the wall corner.

Metal Planter Stand
Assembly Instructions
Produced in China for A. Mir & Co., Ltd.
© A. Mir & Co., Ltd.  3 / 4

www.royalcraft.co.uk
Components, fixtures & fittings (not actual size)
Parts List
Part
No. Diagram Qty. Part No. Diagram Qty.
A
Frame
1 PC B
Top Tray
1 PC
C 
MiddleTray
1 PC D 
BottomTray
1 PC
N10

M5*10Bolt
12 PCS DP
Washer
12 PCS
F4
M5 Nut
12 PCS AK
Allen Key
1 PC
F1
Spanner
1 PC 
Please note the diagram is for reference only, it may not fully represent the
actual appearance of the parts.
Step by step assembly instructions

Metal Planter Stand
Assembly Instructions
Produced in China for A. Mir & Co., Ltd.
© A. Mir & Co., Ltd.  4 / 4

www.royalcraft.co.uk
Step One
Stand the Frame (A) and unfold it.
Step Two
With the help of another person,
Assemble the Top Tray (B), Middle Tray (C) and Bottom Tray (D) to the Frame (A) using Washers (DP), Bolts
(N10) and Nuts (F4).
Tighten the Bolts and Nuts by Allen Key (AK) and Spanner (F1). Do not overtighten.
Warning:
This product should NOT be used by Children and Kids!
Load limit is 10 kg per tray. Don’t place goods near the tray rim.
This Planter Stand should be stood close to the wall corner.
PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE