Royalcraft FARO-08 User manual

Produced in China for A Mir & Co., Ltd.
© A Mir & Co., Ltd. 2 / 11
www.a-mir.co.uk
Before you start
Warnings
IMPORTANT, RETAIN FOR FUTURE REFERENCE
READ CAREFULLY
See enclosed instructions for assembly, safety and care
information.
Failure to follow the warnings could result in serious injury.
Handle heavy parts with care.
Ensure that this product is fully assembled as illustrated before
use.
This product should only be used on firm, level ground.
Keep small parts out of reach of children.
Do not stand or climb onto this product.
This product is intended for domestic use only.
Furniture can be dangerous if incorrectly used. No liability will be
accepted for damage or injury caused by incorrect use of this
product.
Dos
When you are ready to start, make sure that you have the right
tools, plenty of space and a clean, dry area for assembly.
Remove all packaging and banding and place the components
carefully on suitable surfaces to prevent damaging or scratching
them.
Check the pack and make sure you have all of the parts listed.
Check all screws and bolts are tightened and inspect regularly.
This product is suitable for all year outdoor use, but we
recommend that a furniture cover be used to add additional
protection to your product when not in use.
PLEASE NOTE - All cushions should be stored indoors after use.
The cushions are not waterproof.
During severe weather conditions and in the winter months we
recommend moving your furniture inside into a cool, dry place.
Before storage, ensure that the product is clean and dry.
To clean, wipe down with a sponge and warm soapy water and
wipe with a clean, dry cloth.
Cushions should be cleaned following the care instruction on the
label.
Don’ts
Do not use scourers, abrasives, washing powders, chemical cleaners
or any other substances containing abrasives since these substances
can damage the product, including the glass panel.
Never tilt the chair during use.
Do not place very hot or very cold items on the glass surface
unless adequately thick table-mats are used to prevent such
items from coming into contact with the glass.
Do not use the glass as a chopping surface. Do not strike glass
with hard or pointed items.
Do not strike the glass with hard or pointed items.
Do not use power tools to construct this product.
Do not use this product if parts are missing, damaged or worn.
Do not sit or lean on the table.
Do not stand or climb onto the product and do not use it as a ladder,
as this could lead to it unbalancing and overturning.
Never drag furniture when moving it, always lift it.
Number of people required for assembly
Two people
Time to assemble
35 minutes
Tools required
(Rubber Hammer may be required, not provided)
Tips:
Do NOT fully tighten bolts before
all components are connected.
Only fully tighten once you are
satisfied with the alignment of all
components.
Do not overtighten bolts.
Faro 4pcs Lounge Set - Arm Chair and Coffee Table
Assembly Instructions

Produced in China for A Mir & Co., Ltd.
© A Mir & Co., Ltd. 3 / 11
www.a-mir.co.uk
Please find the member parts.
Member Part
Part No. Diagram Name Qty.
MP1 Coffee Table 1 PC
MP2 Arm Chair 2 PCS
Faro 4pcs Lounge Set - Arm Chair and Coffee Table
Assembly Instructions

Produced in China for A Mir & Co., Ltd.
© A Mir & Co., Ltd. 4 / 11
www.a-mir.co.uk
Components, fixtures & fittings (not actual size)
Parts List
Part
No. Diagram Qty. Part No. Diagram Qty.
NST
Coffee Table Leg
2 PCS LST
Side Panel
2 PCS
FT
Coffee Table Bottom Panel
1 PC T
Coffee Table Top
1 PC
RS
Right Leg/Armrest
2 PCS LS
Left Leg/Armrest
2 PCS
CB
Front Backrest
2 PCS CBC
Rear Backrest
2 PCS
Faro 4pcs Lounge Set - Arm Chair and Coffee Table
Assembly Instructions

Produced in China for A Mir & Co., Ltd.
© A Mir & Co., Ltd. 5 / 11
www.a-mir.co.uk
CF
Front Panel
2 PCS CR
Rear Panel
2 PCS
BR
Rear Right Foot Cap
2 PCS BL
Rear Left Foot Cap
2 PCS
LF
Front Left Foot Cap
2 PCS RF
Front Right Foot Cap
2 PCS
CS
Seat Panel
2 PCS A
Cushion
2 PCS
Faro 4pcs Lounge Set - Arm Chair and Coffee Table
Assembly Instructions

Produced in China for A Mir & Co., Ltd.
© A Mir & Co., Ltd. 6 / 11
www.a-mir.co.uk
N
Nut
4 PCS B
Bolt
32 PCS
S
Spanner
1 PC
Step by step assembly instructions
MP1 – Coffee Table
Step One
Attach Side Panels (LST) to the Coffee Table Leg (NST).
NST
LST
Faro 4pcs Lounge Set - Arm Chair and Coffee Table
Assembly Instructions

Produced in China for A Mir & Co., Ltd.
© A Mir & Co., Ltd. 7 / 11
www.a-mir.co.uk
Step Two
Attach Coffee Table Bottom Panel (FT) to the above partly-assembled parts.
Attach another Coffee Table Leg (NST) to the above partly-assembled parts.
Place the assembled parts in the upright position.
Step Three
Attach the Coffee Table Top (T) to the above partly-assembled parts.
Your Coffee Table is now ready for use.
Note: This Coffee Table is with Storage Facility.
NST
FT
Faro 4pcs Lounge Set - Arm Chair and Coffee Table
Assembly Instructions

Produced in China for A Mir & Co., Ltd.
© A Mir & Co., Ltd. 8 / 11
www.a-mir.co.uk
MP2 – Arm Chair
Step One
Attach Front Panel (CF) to the Seat Panel (CS).
Attach Front Backrest (CB) to the Seat Panel (CS).
Step Two
Tighten the parts using Nuts (N), Bolts (B) by Spanner (S).
2 Nuts and 2 Bolts are used in this step.
CF
CF
CS
CS
CF
CS
N
B
S
CB
CB
Faro 4pcs Lounge Set - Arm Chair and Coffee Table
Assembly Instructions

Produced in China for A Mir & Co., Ltd.
© A Mir & Co., Ltd. 9 / 11
www.a-mir.co.uk
Step Three
Attach the Rear Panel (CR) to the Seat Panel (CS) using Bolts (B).
2 Bolts are used in this step.
Step Four
Attach above partly-assembled parts to the Left Leg/Armchair (LS) using Bolts (B).
6 Bolts are used in this step.
CR
CS
LS
B
B
Faro 4pcs Lounge Set - Arm Chair and Coffee Table
Assembly Instructions

Produced in China for A Mir & Co., Ltd.
© A Mir & Co., Ltd. 10 / 11
www.a-mir.co.uk
Step Five
Attach above partly-assembled parts to the Right Leg/Armchair (RS) using Bolts (B).
6 Bolts are used in this step.
Step Six
Attach Rear Right Foot Cap (BR), Rear Left Foot Cap (BL), Front Left Foot Cap (LF) and
Front Right Foot Cap (RF) to the bottom side of the Legs.
LF
RF
RS B
BR
BL
Faro 4pcs Lounge Set - Arm Chair and Coffee Table
Assembly Instructions

Produced in China for A Mir & Co., Ltd.
© A Mir & Co., Ltd. 11 / 11
www.a-mir.co.uk
Step Seven
Attach Rear Backrest (CBC) to the above partly-assembled parts.
Step Eight
Place the Arm Chair in the upright position. Attach Cushion (A) to the Seat Panel (CS).
Your Arm Chair is now ready for use.
A
Never tilt the product during use.
Ensure the product is always placed firmly
on the ground.
PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE
CBC
Faro 4pcs Lounge Set - Arm Chair and Coffee Table
Assembly Instructions