Royalcraft Walton User manual

Walton Coffee Set
Assembly Instructions
ProducedinChinaforA.Mir&Co.,Ltd.
© A. Mir & Co., Ltd. 1 / 9

www.ro
y
alcraft.co.uk
Product size:
Coffee Table: L85*W45*H38 cm
Armchair: W58*D60*H74 cm
Loveseat: W110*D60*H74 cm
The frame of this product is manufactured from mild steel coated with a weather resistant paint.
Steel has a natural tendency to rust over time and, whilst we expect you to be able to enjoy your
furniture for many years to come, we recommend that you check the product from time to time for
signs of paint damage and/ or rust. If the paint should become damaged, or if rust begins to form,
you should clean the affected area and apply a suitable “thinners based” touch-up paint.
Such paints are readily available from all good hardware and DIY stores.”
IMPORTANT, RETAIN FOR FUTURE REFERENCE
READ CAREFULLY

Walton Coffee Set
Assembly Instructions
ProducedinChinaforA.Mir&Co.,Ltd.
© A. Mir & Co., Ltd. 2 / 9

www.ro
y
alcraft.co.uk
Before you start
Warnings
IMPORTANT, RETAIN FOR FUTURE REFERENCE
READ CAREFULLY
See enclosed instructions for assembly, safety and care
information.
Failure to follow the warnings could result in serious injury.
Handle heavy parts with care.
Ensure that this product is fully assembled as illustrated before
use.
This product should only be used on firm, level ground.
Keep small parts out of reach of children.
Do not stand or climb onto this product.
This product is intended for domestic use only.
Furniture can be dangerous if incorrectly used. No liability will be
accepted for damage or injury caused by incorrect use of this
product.
Dos
When you are ready to start, make sure that you have the right
tools, plenty of space and a clean, dry area for assembly.
Remove all packaging and banding and place the components
carefully on suitable surfaces to prevent damaging or scratching
them.
Check the pack and make sure you have all of the parts listed.
Check all screws and bolts are tightened and inspect regularly.
This product is suitable for all year outdoor use, but we
recommend that a furniture cover be used to add additional
protection to your product when not in use.
During severe weather conditions and in the winter months we
recommend moving your furniture inside into a cool, dry place.
Before storage, ensure that the product is clean and dry.
To clean, wipe down with a sponge and warm soapy water and
wipe with a clean, dry cloth.
Cushions should be cleaned following the care instruction on the
label.
Don’ts
Do not use scourers, abrasives, washing powders, chemical cleaners
or any other substances containing abrasives since these substances
can damage the product, including the glass panel.
Never tilt the chair during use.
Do not place very hot or very cold items on the glass surface
unless adequately thick table-mats are used to prevent such
items from coming into contact with the glass.
Do not use the glass as a chopping surface. Do not strike glass
with hard or pointed items.
Do not strike the glass with hard or pointed items.
Do not use power tools to construct this product.
Do not use this product if parts are missing, damaged or worn.
Do not sit or lean on the table.
Do not stand or climb onto the product and do not use it as a ladder,
as this could lead to it unbalancing and overturning.
Never drag furniture when moving it, always lift it.
Number of people required for assembly
Two people.
Time to assemble
40 minutes
Tools required


Tips:
Do NOT fully tighten bolts before
all components are connected.
Only fully tighten once you are
satisfied with the alignment of all
components.
Do not overtighten bolts.

Walton Coffee Set
Assembly Instructions
ProducedinChinaforA.Mir&Co.,Ltd.
© A. Mir & Co., Ltd. 3 / 9

www.ro
y
alcraft.co.uk
This Coffee Set is a combination set of 4 pieces.
Please find the combination part.
Member Parts
Combination
Part No. Diagram Name Qty.
MP1
Armchair 2 PCS
MP2
Loveseat 1 PC
MP3
Coffee Table 1 PC

Walton Coffee Set
Assembly Instructions
ProducedinChinaforA.Mir&Co.,Ltd.
© A. Mir & Co., Ltd. 4 / 9

www.ro
y
alcraft.co.uk
Components, fixtures & fittings (not actual size)
Parts List
Part
No. Diagram Qty. Part No. Diagram Qty.
A

LeftLeg
3 PCS B

RightLeg
3 PCS
C

Armchair Seating
2 PCS D

Armchair Backrest
2 PCS
E

LeftBackrestforLoveseat
1 PC F

RightBackrestforLoveseat
1 PC
G

LoveseatSeating
1 PC H

Coffee Table Top Frame
1 PC
I 
Coffee Table Leg 4 PCS J

Coffee Table Glass Top
1 PC

Walton Coffee Set
Assembly Instructions
ProducedinChinaforA.Mir&Co.,Ltd.
© A. Mir & Co., Ltd. 5 / 9

www.ro
y
alcraft.co.uk
K
M6 Nut Cap
3 PCS L
M6*15mm Bolt
26
PCS
M
M6*25mm Bolt
12
PCS
N
M6*40mm Bolt
3 PCS
O
M6 Nut
3 PCS P
M6 Washer
44
PCS
Q
41
PCS
R
Spanner
2 PCS
Step by step assembly instructions
Note: All Bolt Head Caps and Nut Caps should not be attached before finally tightening all Bolts with
Spanner or Allen Key (optional).
Only tighten all bolts when you are satisfied with the alignment of all components.
Identify the Backrest for the Armchair and Loveseat before assembly
Part D is for the Armchair, it has 4 assembly holes.
Part E and F is for the Loveseat, they have 5 assembly holes respectively.
When assemble the Part E and F, the sides with 3 assembly holes should be near each other.

Walton Coffee Set
Assembly Instructions
ProducedinChinaforA.Mir&Co.,Ltd.
© A. Mir & Co., Ltd. 6 / 9

www.ro
y
alcraft.co.uk
MP1 - Armchair
Step One
Assemble the Armchair Seating (C) to the
Left Leg (A) and Right Leg (B)
using Washers (P), Bolts (L) and
Bolt Head Caps (Q).
Step Two
Assemble the Backrest (D) to the
Left Leg (A) and Right Leg (B)
using Washers (P), Bolts (M) and
Bolt Head Caps (Q).
Your Armchair is now ready for use. 

Walton Coffee Set
Assembly Instructions
ProducedinChinaforA.Mir&Co.,Ltd.
© A. Mir & Co., Ltd. 7 / 9

www.ro
y
alcraft.co.uk
MP2 – Loveseat
Step One
Assemble the Loveseat Seating (G) to the
Left Leg (A) and Right Leg (B)
using Washers (P), Bolts (L) and
Bolt Head Caps (Q).
Step Two
Assemble the Backrest (E) and (F) to the
rear part of Loveseat Seating (G).
using Washers (P), Bolts (N),
Bolt Head Caps (Q), Nuts (O) and Nut Caps (K).
Assemble the Backrest (E) and (F) to the
Left Leg (A) and Right Leg (B)
using Washers (P), Bolts (M) and
Bolt Head Caps (Q).
Your Armchair is now ready for use. 

Walton Coffee Set
Assembly Instructions
ProducedinChinaforA.Mir&Co.,Ltd.
© A. Mir & Co., Ltd. 8 / 9

www.ro
y
alcraft.co.uk
MP3 - Coffee Table
Step One
Open the packaging, leave the glass on the carton
until the rest of the table is fully assembled.
With the help of another person,
place the Coffee Table Top Frame (H) upside down
on a flat, non-abrasive surface to
avoid scratching the table surface or rim.
Step Two
Assemble each Coffee Table Leg (I)
To the Coffee Table Top Frame (H)
using Washers (P), Bolts (L) and
Bolt Head Caps (Q).
Once you are satisfied with
the alignment of the components
carefully tighten all bolts using Spanner (R).
Do not over-tighten.
Cover each bolt with Bolt Head Cap (Q).

Walton Coffee Set
Assembly Instructions
ProducedinChinaforA.Mir&Co.,Ltd.
© A. Mir & Co., Ltd. 9 / 9

www.ro
y
alcraft.co.uk
Step Three
With the help of another person, carefully
turn the table frame in the upright position.
Carefully place the Coffee Table Glass Top (J)
on the Coffee Table Top Frame (H) and
make sure the Glass Top is fully
rested on/in the frame.
Your Coffee Table is now ready for use. 




Never tilt the Armchair or Loveseat during use.
Ensure the product is always placed firmly
on the ground.
PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE