Ruby Tech PSES-2126C User manual

PSES-2126C
BenefitsBenefits
PoE Save Your Power Infrastructure and Installation Cost
24-PoE ports allow power (185W) to be supplied to end devices, such as
Wireless Access Points or VoIP Phones, directly through the existing LAN
cables, eliminating costs for additional AC wiring and reducing Installation
Cost. It frees your wireless AP deployment from restriction due to power
outlet location. By supplying the power end-span, you can centralize power
distribution and backup without the need to increase infrastructure.
QoS with Four Priority Queues
The QoS(Quality Of Service) feature provides four internal queues to support
four different classifications of traffic. High priority packet streams experience
less delay inside the switch, which supports lower latency for certain delay-
sensitive traffic. The PSES-2126C can classify the packet as one of the four
priorities according to vip port, 802.1p priority tag, DiffServ and/or IP TOS.
The QoS operate at full wire speed. The actual scheduling at each egress
port can be based upon a strict priority, weighted round robin or a mix of both.
Port Mirroring
This mechanism helps track network errors or abnormal packet transmission
without interrupting the flow of data. Allow ingress traffic to be monitored by a
single port that is defined as mirror capture port. The mirror capture port can
be any 10/100 port, 10/100/1000 port. Mirroring multiple ports is possible but
can create congestion at the mirror capture port.
Q-in-Q VLAN for performance & security
The VLAN feature in the switch offers the benefits of both security and
performance. VLAN is used to isolate traffic between different users and thus
provides better security. Limiting the broadcast traffic to within the same
VLAN broadcast domain also enhances performance. VLAN support enabling
advanced techniques such as "802.1Q-in-1Q" to be deployed.
Isolated Group, Provide Secure for Certain Ports
The isolated group feature allows certain ports to be designated as protected.
All other ports are non-isolated. Traffic between isolated group members is
blocked. Traffic can only be sent from isolated group to non-isolated group.
Mac-based 802.ad LACP with Automatic Link Fail-over
Dynamic fail-over means packets will not get assigned to any trunk member
port that has failed. If one of the ports were to fail, traffic will automatically get
distributed to the remaining active ports.
802.1x Access Control Improve Network Security
802.1x features enable user authentication for each network access attempt.
Port security features allow you to limit the number of MAC addresses per port
in order to control the number of stations for each port. Static MAC addresses
can be defined for each port to ensure only registered machines are allowed
to access. By enabling both of these features, you can establish an access
mechanism based on user and machine identities, as well as control the
number of access stations.
802.1d Compatible & 802.1w Rapid Spanning Tree
For mission critical environments with multiple switches supporting STP, you
can configure the switches with a redundant backup bridge path, so
L2 Managed PoE Switch
Gigabit Switch
Gigabit Switch
PSES-2126C: 26-Port L2 Managed Fast Ethernet PoE Switch With 2 SFP Dual Media
Key FeaturesKey Features
Standard compliance
---IEEE 802.3 10Base-T Ethernet
(twisted-pair copper)
---IEEE 802.3u 100Base-TX Ethernet
(twisted-pair copper)
---IEEE 802.3ab 1000Base-T Ethernet
(twisted-pair copper)
---IEEE 802.3z 1000Base-SX/LX
Ethernet
---IEEE 802.3x flow control capability
---ANSI/IEEE 802.3 auto-negotiation
---IEEE 802.1q VLAN
RoHS Compliance
Subscriber Interface
---Port 1-24 are 10/100Mbps Fast
Ethernet ports.
---Port 25,26 are Gigabit TP/SFP Fiber
auto sense
---Auto-Negotiation and Auto-MDIX
---Backpressure flow control for half
duplex.
---802.3x flow control for full duplex.
---Connector: 24 RJ-45 and 2 dual
media, RJ-45/SFP
Performance
Switching capacity:
---Non-blocking switch fabric supports up
to 24FE+2GbE, ports
---8 K MAC addresses
---256k packet buffer and 128k control
memory
---The maximum throughput is 8.8Gbps
---With 64 bytes packets throughput is
6.547Mpps
VSM(Virtual Stacking Management)
---Support 16 devices stacking
---Multiple switches can be managed via
one IP address, just like software
stacking
---Low cost and easily to establish
network environment, not extra
hardware require.
---Not center on the physical location of
wiring closets
VLAN
---Supports SVL/IVL configuration to
meet your VLAN requirement
---Port-base VLAN
RUB
TECHTECH
Networking & Communications
R

---IEEE802.1q tag-base VLAN, 4094
max, up to 256 active VLANs included
static plus dynamic entry
---IEEE802.1q tag-base VLAN
---Flooding unknown vlan frame setting,
can flood packet with some vlan tag
associated to a invalid/inactive vlan
---In tag-base VLAN, supports egress/
ingress packet filter
---Q-in-Q is an efficient method for
enabling Subscriber Aggregation.
QoS
---Port Based (VIP Port), 802.1p , TOS
and Diffserv(IPv4/IPv6) based QoS
packet classification
---Supports four level priority queues to
prioritize in-bound and out-bound
traffic
---Supports two scheduling, WRR and
Strict
---Supports priority in a Q-in-Q tag
Broadcast Storm
---Multicast/Broadcast/Unknown-Unicast
Storm suppression.
Port Mirroring
---Support 1: N RX port mirroring.
---Supports port sniffer function with 3
modes:
(TX Monitor Mode, RX Monitor Mode
and TX-RX pair Monitor Mode).
Isolated Group
---Provide one group allows certain
ports to be designated as protected.
Restricted Group
---Can decide the direction of
transmitting packets for the specific
port
Restricted Group
---Can decide the direction of tran
smitting packets for the specific port
Rate Limit
---Ingress rate limit:
Port 1~24: 1K up to 100Mbps
Port 25, 26: 1K up to 1000Mbps
---Egress rate limit:
Port 1~24: 1K up to 100Mbps
Port 25, 26: 1K up to 1000Mbps
PoE Specification
---24 IEEE802.3af PoE PSE ports
---Endpoint with 48VDC power through
RJ-45 pin 1, 2, 3, 6.
---PoE-PSE activity LED indicator.
---185 watts of total power (up to 15.4
watts for 12 ports, or up to 7.7 watts
for 24 ports)
---Auto detect powered device and
consumption levels
---Supports per port power consumption
monitoring
---Smart feature for PD on/off, PD
detection, power level, PD status and
power feeding priority
---Circuit protection to prevent power
interference between ports
---Supports per port PoE State setting
transmission and reception of packets can be guaranteed in event of any fail-
over switch on the network.
2 Dual Media for Flexible Fiber Connection
Dual media port 25 and 26 are provided for flexible fiber connection. You can
select to install optional transceiver modules in these slots for short, medium
or long distance fiber backbone attachment. Use of the SFP will disable their
corresponding built-in 10/100/1000Base-T connections.
Broadcast/Multicast/Unknown-unicast Storm Control
To limit too many broadcast/multicast/unknown-unicast flooding in the network,
broadcast/multicast storm control is used to restrict excess traffic. Threshold
values are available to control the rate limit for each port. Packets are
discarded if the count exceeds the configured upper threshold.
Technical SpecificationsTechnical Specifications
LED Description
Cable and Maximum Length:
LED Color Function
System LED
CPURUN Green -Blinkswhen CPU ison and good
POWER Green -Litwhen ACpower is onand good
ACT Green -Litwhen LEDSET set on activemode
FDX Green -Litwhen LEDSET set on full-duplexmode
SPD Green -Litwhen LEDSET set on speedmode
10/100Mbps Ethernet TPPort 1 to24 LED
LNK Green -Litwhen connection withremote device isgood
-Off when cable connection isnot good
ACT/FDX Amber (a)LEDSET set on ACT(active) mode:
/ SPD (TPPort -Blinks whenany traffic is present
1 to 24 (b)LEDSET set on FDX (full-duplex)mode:
LED) -Lit whenfull-duplex mode isactive
-Blinks when anycollision is present
(c)LEDSET set on SPD (speed)mode:
-Lit when 100Mbpsspeed is active
-Off when 10Mbps speed isactive
10/100/1000Mbps Gigabit TP/FiberPort 25, 26LED
LNK Green -Litwhen connection withremote device isgood
-Off when cable connection isnot good
FX Green -Litwhen Fiber portis active
-Off when TP port is active
ACT/FDX Green (a)LEDSETset onACT (active) mode:
/ SPD (Port25, -Blinks whenany traffic is present
26 LED) (b)LEDSETset on FDX(full-duplex) mode:
-Lit when full-duplexmode is active
-Blinks when anycollision is present
(c)LEDSET set on SPD (speed)mode:
-Lit when 1000Mbpsspeed is active
-Off when 10/100Mbps speed isactive
PoE Port StatusIndication LEDs
PoE-PSE Green -Litwhen PoE Poweris active
ACT
Gigabit Switch
Gigabit Switch
L2 Managed PoE Switch
TP Cat. 5 UTPcable, up to100m
1000Base-SX SC M-M Up to 220/275/500/550m,
which depends onMulti-Mode Fiber type
1000Base-LX SC S-M Single-Mode Fiber,up to10/30/50Km
1000Base-LX WDM SCS-M Single-Mode Single Fiber, Bidi 20Km
RUB
TECHTECH
Networking & Communications
R

Gigabit Switch
L2 Managed PoE Switch
Technical SpecificationsTechnical Specifications
Hardware Spec.
Packing InformationPacking Information
Weight 3.3kg
Feature Detailed Description
Voltage 100~240 VAC
Frequency 50~60 Hz forAC Power
Power Requirement 210W
Total Power for PoE 185W
Ambient Temperature 0 to 40 C
Humidity 5% to 90%
Dimensions 45(H) x 442(L) x 366(W) mm,19" 1U
Safety Comply with FCCPart 15 ClassA&
CE MarkApproval
Carton Dimensions (mm) pcs/Carton N.W (KG) G.W (KG)
530x512x345 5 21 22
---Supports per port power priority
setting
Protocol
LACP
---2 Fast Ethernet +1 Gigabit Ethernet
groups
---Per-group max 4 members
---Provides DA, SA and DA+SA Mac-
based trunking with automatic link
fail-over
GVRP/GARP
---802.1q with GVRP/ GARP
Multicasting
---Supports IGMP snooping including
active and passive mode
STP/RSTP
---802.1d/1w/1s STP
Network Security
---802.1x access control
---Isolated group
---Restricted group
---Management Access Policy Control
---Static mac, to limit which mac
addresses can pass through or not
---Mac addresses learning limit, to set up
the maximum amount of mac that
each port can learn
Snmpv1,v2c Network Management
RFC 1213 MIB (MIB-II)
---Interface MIB
---Address Translation MIB
---IP MIB
---ICMP MIB
---TCP MIB
---UDP MIB
---SNMP MIB
RFC 1757 RMON MIB
---Statistics Group 1
---History Group 2
---Alarm Group 3
---Event Group 9
RFC 1493 Bridge MIB
RFC 1643 Ethernet MIB
Enterprise MIB
Overview
PSES-2126C supports 24 10/100Mbps
Auto-negotiation, Auto-MDIX Ethernet
ports and Power over Ethernet to IEEE
802.3af compliant devices. With the
24-port featuring PoE function, the
PSES-2126C is an ideal solution for
wireless AP, VoIP phones, security video
cameras. It's fully compliant with the
standards of IEEE 802.3/u/x/z/ab/af. It is
equipped with 24 UTP (RJ-45) ports and
2 of which are dual media ports that
accommodate optional 10/100/1000
Base-T or SFP modules. In addition, the
switch implements the QoS (Quality of
Service), Mac Filtering Policy, Port Mirror,
VLAN and full L2 protocol. The overall
network management is enhanced and
the network efficiency is also improved
to accommodate high bandwidth
applications with security.
Gigabit Switch
RUB
TECHTECH
Networking & Communications
R
Note:
We recommend the SFP transceiver from thefollowing vendors:
1. Ruby TechCorporation
2. Agilient Technologies
3. AVAGOTechnologies
4. Finisar Corporation
Ruby Tech Corp.
3F, No.1, Lane 50, Nan Kang Road, Sec.3, Taipei, Taiwan http://www.rubytech.com.tw
TEL:[phone] FAX:[phone] E-mail [email protected]
2008-07.25 Version A
Technicalinformation listed issubject to changewithout prior notice. All brand namesand trademarks are property of theirrespective owners.
Copyright c 2008 Ruby Tech Corp. Allrights reserved.
Optional SFP Module
SFP.LC 1000Base-SX GE SFPFiber Module,
LC Multi-Mode 850nm
SFP.LC.M2 1000Base-SX GE SFPFiber Module,
LC Multi-Mode 1310nm 2km
PSES-2126C 26-Port L2 ManagedFast Ethernet PoE Switch
With 2 SFPDual Media