Ruijie Reyee RG-ES206GS-P Series Installation and operating manual

RG-ES206GS-P Series Switches
Hardware Installation and Reference Guide
Document Version: V1.0
Date: 2023.09.11
Copyright © 2023 Ruijie Networks

Copyright
Copyright © 2022 Ruijie Networks
All rights are reserved in this document and this statement.
Without the prior written consent of Ruijie Networks, any organization or individual shall not reproduce, extract,
back up, modify, or propagate the content of this document in any manner or in any form, or translate it into
other languages or use some or all parts of the document for commercial purposes.
,, and other Ruijie networks logos are trademarks of Ruijie Networks.
All other trademarks or registered trademarks mentioned in this document are owned by their respective
owners.
Disclaimer
The products, services, or features you purchase are subject to commercial contracts and terms, and some or
all of the products, services, or features described in this document may not be available for you to purchase or
use. Except for the agreement in the contract, Ruijie Networks makes no explicit or implicit statements or
warranties with respect to the content of this document.
The content of this document will be updated from time to time due to product version upgrades or other
reasons, Ruijie Networks reserves the right to modify the content of the document without any notice or prompt.
This manual is designed merely as a user guide. Ruijie Networks has tried its best to ensure the accuracy and
reliability of the content when compiling this manual, but it does not guarantee that the content of the manual is
completely free of errors or omissions, and all the information in this manual does not constitute any explicit or
implicit warranties.

I
Preface
Intended Audience
This document is intended for:
Network engineers
Technical support and servicing engineers
Network administrators
Technical Support
The official website of Ruijie Reyee: https://www.ruijienetworks.com/products/reyee
Technical Support Website: https://www.ruijienetworks.com/support
Case Portal: https://caseportal.ruijienetworks.com
Community: https://community.ruijienetworks.com
Technical Support Email: [email protected]
Conventions
1. Signs
This document also uses signs to indicate some important points during the operation. The meanings of these
signs are as follows:
Caution
An alert that calls attention to safety instruction that if not understood or followed can result in personal injury.
Warning
An alert that calls attention to important rules and information that if not understood or followed can result in
data loss or equipment damage.
Note
An alert that calls attention to essential information that if not understood or followed can result in function
failure or performance degradation.
Instruction
An alert that contains additional or supplementary information that if not understood or followed will not lead to
serious consequences.
Specification
An alert that contains a description of product or version support.
2. Note
This manual provides installation steps, troubleshooting, technical specifications, and usage guidelines for
cables and connectors. It is intended for users who want to understand the above and have extensive
experience in network deployment and management, and assume that users are familiar with related terms and
concepts.

RG-ES206GS-P Series Switches Hardware Installation and Reference Guide Product Overview
1
1 Product Overview
The RG-ES200 series switches include the following 10 models:
Model
10/100Base-T Ports with
Auto-Negotiation
10/100/1000Base-T
Ports with
Auto-Negotiation
1000Base-
X SFP Port
Consol
e Port
RG-ES205C-P
5 (Ports 1-4 support
PoE/PoE+)
/
/
/
RG-ES205GC-
P
/
5 (Ports 1-4 support
PoE/PoE+)
/
/
RG-ES209C-P
8 (Ports 1-8 support
PoE/PoE+)
1
/
/
RG-ES209GC-
P
/
9 (Ports 1-8 support
PoE/PoE+)
/
/
RG-ES218GC-
P
/
16 (Support PoE/PoE+)
2
/
RG-ES226GC-
P
/
24 (Support PoE/PoE+)
2
/
RG-ES224GC
/
24
/
/
RG-ES216GC
/
16
/
/
RG-ES205GC
/
5
/
/
RG-ES208GC
/
8
/
/
RG-ES206GC-
P
/
6 (Ports 1-4 support
PoE/PoE+)
/
/
RG-ES210GC-
LP
/
10 (Ports 1-8 support
PoE/PoE+)
/
/
RG-ES206GS-
P
/
6 (Ports 1-4 support
PoE/PoE+)
6F Port
supports
SFP
/
RG-ES210GS-
P
/
10 (Ports 1-8 support
PoE/PoE+)
10F Port
supports
SFP
/
Note
●A SFP port is not downward compatible with 100Base-FX.

RG-ES206GS-P Series Switches Hardware Installation and Reference Guide Product Overview
2
●1000Base-T ports are downward compatible with 100Base-TX and 10Base-T ports.
1.1 Package Contents
Table 1-1 RG-ES206GS-P Package Contents
Item
Quantity
Switch
1
Power adapter
1
User Manual
1
Power cord
1
Warranty card
1
Note
The package contents above are intended to provide a general overview, and are subject to the terms of the
order contract. Please check your goods carefully against the package contents or order contract. If you have
any questions, please contact the distributor.
1.2 Technical Specifications
Table 1-2 Technical Specifications
Model
RG-ES206GS-P
Port
Ports 1-6 are 10/100/1000Base-T ports with auto-negotiation, in which ports 1-4
supporting PoE/PoE+, while ports 5 and 6 do not support PoE/PoE+. Port 6 and
port 6F form a combo port.
Power Supply
AC input:
Rated voltage range: 100 VAC to 240 V AC
Max. voltage range: 90 VAC to 264 V AC
Frequency: 50 Hz to 60 Hz
Rated current: 1.5 A
Power cord: 3-pin 10A power cord
DC output:
Rated voltage range: 54 V DC
Rated current: 1.11 A
Power adapter connector: outer diameter: 5.5 mm, inner diameter: 2.1 mm, depth:
10 mm

RG-ES206GS-P Series Switches Hardware Installation and Reference Guide Product Overview
3
EEE
Not supported
PoE
PoE standards: IEEE802.3af and 802.3at.
Ports 1-4 are PoE/PoE+ ports, each supporting a maximum PoE+ output of 30 W.
Ports 5 and 6 do not support PoE standard.
Overall max. PoE/PoE+ power output: 54 W
PoE Power Cable
Pairs
Mode A (1-2, 3-6 pairs)
Max. Power
Consumption
Power consumption (No PoE load) < 6W
Power consumption (PoE full load) < 60W
Port Status LED
Toggle Switch
LED switch toggled to left (Mode 1): the port LED status indicates the status of
traffic transmission. Solid green means that the port is link up, while blinking green
means that the port is transmitting and receiving data.
LED switch toggled to right (Mode 2): The port LED status indicates the PoE
status. Solid green means that the port is supplying power, while blinking green
means that the port is in power overload state.
Reset Button
Press the button for less than 2 seconds and release, the switch restarts.
Press the button for more than 5 seconds and release after the system LED starts
blinking, the switch restores to factory defaults and restarts.
Operating
Temperature
0ºC to 40ºC
Storage
Temperature
–40°C to +70°C
Operating
Humidity
10% to 90% RH (non-condensing)
Storage Humidity
5% to 95% RH (non-condensing)
Fan
Fanless design
Temperature Alarm
Not supported
DDM
Not supported
Safety Standard
CE Certification
Max. Ground
Leakage Current
≤1.5 mA
Dimensions (W x D
x H)
149 mm (5.87 in.) x 79 mm (3.11 in.) x 26 mm (1.02 in.)
Weight
1.1 kg (12.79 lbs, package included)

RG-ES206GS-P Series Switches Hardware Installation and Reference Guide Product Overview
4
Caution
Operation of this equipment in a residential environment could cause radio interference.
1.3 Product Appearance
The RG-ES206GS-P switch provides 8 ×10/100/1000Base-T ports on the front panel, and a DC power input
port for 54V PoE injector on the back panel.
Figure 1-1 Appearance of RG-ES206GS-P
Front Panel
Figure 1-2 Front Panel of RG-ES206GS-P
Note
1. System status indicator of the switch
2. Electrical port status indicator
3. 10/100/1000Base-T port with
auto-negotiation
4. Electrical port status indicator
5. 10/100/1000Base-T port with
auto-negotiation
6. Optical port status indicator
7. Label (at the bottom)
Rear Panel

RG-ES206GS-P Series Switches Hardware Installation and Reference Guide Product Overview
5
Figure 1-3 Back Panel of RG-ES206GS-P
Note
1. Grounding stud
2. Reset button
3. LED mode switch
4. DC power input
5. Kensington lock
Note
●Reset button: Press for less than 2 seconds and release, the system restarts; press for more than 5
seconds until the system LE blinks, and then release, the system restores to factory settings and restarts.
●LED switch toggled to left (Mode 1): the port LED status indicates the status of traffic transmission. Solid
green means that the port is link up, while blinking green means that the port is transmitting and receiving
data.
●LED switch toggled to right (Mode 2): The port LED status indicates the PoE status. Solid green means
that the port is supplying power, while blinking green means that the port is in power overload state.
Cooling
RG-ES206GS-P adopts natural cooling. To ensure that the switch works properly in the specified environment,
a minimum clearance of 100 mm (3.94 in.) must be maintained around the device to ensure proper ventilation.
Dust the device every three months to avoid blocking the ventilation openings on the housing.
Figure 1-4 LED
LED
Panel
Identification
Status
Description
Status LED
SYS
Off
System is not powered on.
Blinking
green
If the power of PoE exceeds 54W, the
newly connected PD cannot be
powered up because of insufficient
power, but the switching function will
remain affected.
Solid
green
System is operating normally.
PoE status indicator of
1–4
Off
PoE is disabled.

RG-ES206GS-P Series Switches Hardware Installation and Reference Guide Product Overview
6
the RJ-45 port
Solid
green
PoE is enabled.
Blinking
green
PoE is abnormal.
RJ-45 Port Link/Ack
Status LED
1–6
Off
No link is detected for this port.
Solid
green
The port operates 10/100/1000 Mbps.
Blinking
green
The port is sending and receiving traffic
at 10/100/1000 Mbps.
SFP port LED
Appearance of
the 6F
Off
No link is detected for this port.
Solid
green
The port operates at1000 Mbps.
Blinking
green
The port is sending and receiving traffic
at 1000 Mbps.

RG-ES206GS-P Series Switches Hardware Installation and Reference Guide Preparing for Installation
7
2 Preparing for Installation
2.1 Safety Precautions
Caution
●To avoid personal injury and device damage, carefully read the safety precautions before you install the
device.
●The following safety precautions may not cover all possible dangers.
2.1.1 Installation Safety
Keep the chassis clean, free from any dust.
Do not place the device in walking areas.
During the installation and maintenance, do not wear loose clothes, ornaments, or any other things that may
be hooked by the device.
Cut off all the power supplies and unplug all power cords before placing the device in a rack or removing the
device from a rack.
2.1.2 Handling Safety
Avoid handling the device frequently.
Keep balance and prevent personal injuries when handling the device.
Cut off all the power supplies and unplug all power cords before moving or handling the switch.
2.1.3 Electric Safety
Observe local regulations and specifications during electric operations. Only personnel with relevant
qualifications can perform such operations.
Before installing the device, check whether there are hidden risks in the operating environment of the device.
For example, check whether the power socket is grounded and whether the ground is wet.
Be sure to know the location of the indoor emergency power supply switch before installing the device.
When an accident occurs, immediately cut off all power supplies.
Do not maintain the device by yourself when the device is powered on.
Make sure that the switch is powered off when you cut off the power supply.
Do not place the switch in a wet position, and keep the switch away from liquid.
Caution
●Improper or incorrect electric operations may cause a fire, electric shock, and other accidents, and lead to
severe and fatal personal injury and device damage.
●Direct contact or indirect contact through wet objects with high voltage or mains power supply may be fatal.
●If the power supply system is equipped with a leakage protector (also referred to as leakage current switch
or leakage current breaker), the rated leakage action current of each leakage protector must be greater
than twice the theoretical maximum leakage current of all the power supplies in the system. For example,