Ruijie RG-ES100 Series Installation and operating manual

Ruijie Reyee RG-ES100 Series Switches
Hardware Installation and Reference Guide

Copyright Statement
Ruijie Networks©2021
Ruijie Networks reserves all copyrights of this document. Any reproduction, excerption, backup, modification,
transmission, translation or commercial use of this document or any portion of this document, in any form
or by any means, without the prior written consent of Ruijie Networks is prohibited.
Exemption Statement
This document is provided “as is”. The contents of this document are subject to change without any notice.
Please obtain the latest information through the Ruijie Networks website. Ruijie Networks endeavors to
ensure content accuracy and will not shoulder any responsibility for losses and damages caused due to
content omissions, inaccuracies or errors.

Preface
Thank you for using our products. This manual will guide you through the installation of the device.
This manual describes the functional and physical features and provides the device installation steps,
hardware troubleshooting, module technical specifications, and specifications and usage guidelines for
cables and connectors.
Audience
It is intended for the users who have some experience in installing and maintaining network hardware. At
the same time, it is assumed that the users are already familiar with the related terms and concepts.
Obtaining Technical Assistance
Ruijie Networks Website: https://www.ruijienetworks.com/
Technical Support Website: https://ruijienetworks.com/support
Case Portal: https://caseportal.ruijienetworks.com
Community: https://community.ruijienetworks.com
Technical Support Email: [email protected]
Skype: [email protected]
Related Documents
Documents
Description
Configuration Guide
Describes network protocols and related mechanisms that
supported by the product, with configuration examples.
Command Reference
Describes the related configuration commands, including
command modes, parameter descriptions, usage guides, and
related examples.
Symbol Conventions
The symbols used in this document are described as below:
Means reader take note. Notes contain helpful suggestions or references.
This symbol means that you must be extremely careful not to do some things that may damage the
device or cause data loss

Ruijie RG-ES100 Series Switches Hardware Installation and Reference Guide
1 Product Overview
The RG-ES100 series switches include the following models:
Model
10/100Base-TX Auto-sensing
Ethernet Port
10/100/1000Base-T
Auto-sensing
Ethernet Port
1000Base-X SFP
Port
Console
Port
RG-ES106D-P
6（Ports 1-4 support PoE/PoE+）
N/A
N/A
N/A
RG-ES126S-LP
24（Ports 1-24support PoE/PoE+）
2
1 (Combo)
N/A
RG-ES110D-P
8（Ports 1-8 support PoE/PoE+）
2
N/A
N/A
RG-ES116G
N/A
16
N/A
N/A
RG-ES124GD
N/A
24
N/A
N/A
RG-ES118S-LP
16（Ports 1-16 support PoE/PoE+）
2
2 (Combo)
N/A
1000Base-T is downward compatible with 100Base-TX and 10Base-T.
The SFP ports cannot be downward compatible with 100Base-FX.
1.1 RG-ES106D-P
Technical Specifications
Model
RG-ES106D-P
Ports
6 10/100Base-TX auto-sensing Ethernet ports, ports 1-4 support PoE/PoE+.
Power Supply
AC input
Rated voltage range: 100 VAC to 240 VAC
Maximum voltage range: 90 VAC to 264 VAC
Frequency: 50/60 Hz
Rated current: 1.5 A
Adapter output
Rated voltage range: 51 VDC
Rated current range: 1.25 A
EEE
Not supported
PoE
Support PoE and PoE+.
Ports 1-4 are PoE/PoE+-capable with the maximum power output of 30W per port. Ports 5-6 do
not support PoE or PoE+.
The overall maximum output power of PoE/PoE+ is 58W.
Power
Consumption
Less than 7W with no PoE load
Less than 67W with PoE full load
Operating
Temperature
0℃to 45℃(32°F to 113°F)
Storage
Temperature
-40℃to 70℃(-40°F to 158°F)

Ruijie RG-ES100 Series Switches Hardware Installation and Reference Guide
Operating Humidity
10% to 90% RH
Storage Humidity
5% to 95% RH
Port Mode
Support switchover in three modes:
1. Flow Control On
2. Flow Control Off
3. Port Isolation. When this mode is enabled, ports 1-4 are isolated from each other, but can
communicate with ports 5-6.
Fan
Not supported
Temperature
Warning
Not supported
Accessing Optical
Module Information
Not supported
EMC Standards
GB9254-2008
EN 55032:2015
EN 55035:2017
EN IEC61000-3-2:2019
EN 61000-3-3:2013
Draft ETSI EN 300 386 V2.2.0 (2020-10)
Security Standards
GB4943-2011
EN 62638-1
Earth Leakage
Current
≤1.5mA
Dimensions
(W x D x H)
100 mm x 100 mm x 26 mm (3.94 in. x 3.94 in. x 1.02 in.)
Weight
(With Package)
0.66 kg (1.46 lbs)
The RG-ES106D-P switch is a class A product. In a domestic environment, this product may cause radio interference
in which case the user may be required to take adequate measures.
Product Appearance
RG-ES106D-P provides 6 10/100Base-TX auto-sensing Ethernet ports on the front panel, and a port mode switch-over
button, a system status LED, a power socket and a grounding pole on the back panel.
Figure 1-1 Appearance of RG-ES106D-P

Ruijie RG-ES100 Series Switches Hardware Installation and Reference Guide
Front Panel
Figure 1-2 Front Panel of RG-ES106D-P
Note:
1. Copper port status LED
2. PoE status LED
3. 10/100Base-TX PoE port
4. 10/100Base-TX auto-sensing Ethernet port
Back Panel
Figure 1-3 Back Panel of RG-ES106D-P
Note:
1. Port mode switch-over button
2. System status LED
3. DC power socket
4. Grounding pole
Heat Dissipation
The RG-ES106D-P adopts natural heat dissipation, thereby ensuring normal function of the device. Maintain a minimum
clearance of 100 mm (3.94 in.) around the device. It is recommended to clean the device once every 3 months to avoid
dust from blocking vents.
LEDs

Ruijie RG-ES100 Series Switches Hardware Installation and Reference Guide
LED
Panel Identification
State
Meaning
System status LED
PWR
Off
The switch is powered off.
Solid green
The switch is operational.
RJ45 port status LED
Upper left corner of the
port
Off
The port is not connected.
Solid green
The port is connected at 10/100 Mbps.
Blinking green
The port is receiving or sending traffic at 10/100
Mbps.
RJ45 PoE status LED
Upper left corner of the
port
Off
PoE does not supply power.
Solid green
PoE is operational.
1.2 RG-ES126S-LP
Technical Specifications
Model
RG-ES126S-LP
Ports
Ports 1-24 are 10/100Base-TX auto-sensing Ethernet ports, and support PoE/PoE+
Ports 25 and 26 are 10/100/1000Base-T auto-sensing Ethernet ports, and do not support
PoE/PoE+
Port 26F is a 1000Base-X SFP port multiplexed with Port 26 as a combo port, and the SFP port
takes priority
Power Supply
AC input
Rated voltage range: 100 VAC to 240 VAC
Maximum voltage range: 90 VAC to 264 VAC
Frequency: 50/60 Hz
Rated current: 4 A Max
EEE
Not supported
PoE
Support PoE and PoE+.
Ports 1-24 are PoE/PoE+-capable with the maximum power output of 30W per port. Ports 25-
26 do not support PoE or PoE+.
The overall maximum output power of PoE/PoE+ is 180W.
Power
Consumption
Less than 10W with no PoE load
Less than 220W with PoE full load
Operating
Temperature
0℃to 45℃(32°F to 113°F)

Ruijie RG-ES100 Series Switches Hardware Installation and Reference Guide
Storage
Temperature
-40℃to 70℃(-40°F to 158°F)
Operating Humidity
10% to 90% RH
Storage Humidity
5% to 95% RH
Port Mode
Support switchover in three modes:
1. Flow Control On
2. Flow Control Off
3. Port Isolation. When this mode is enabled, ports 1-24 are isolated from each other, but can
communicate with ports 25, 26 and 26F.
Fan
Supported
Temperature
Warning
Not supported
Accessing Optical
Module Information
Not supported
EMC Standards
GB9254-2008
EN 55032:2015
EN 55035:2017
EN IEC61000-3-2:2019
EN 61000-3-3:2013
Draft ETSI EN 300 386 V2.2.0 (2020-10)
Security Standards
GB4943-2011
EN 62638-1
Earth Leakage
Current
≤1.5mA
Dimensions
(W x D x H)
440 mm x 208 mm x 44 mm (17.32 in. x 8.19 in. x 1.73 in.)
Weight
(With Package)
3 kg (6.61 lbs)
The RG-ES126S-LPswitch is a class A product. In a domestic environment, this product may cause radio interference
in which case the user may be required to take adequate measures.
Product Appearance
RG-ES126S-LP provides 24 10/100Base-TX auto-sensing Ethernet ports, 2 10/100/1000Base-T auto-sensing Ethernet
ports, a 1000Base-X SFP port, system status LEDs and a port mode switch-over button on the front panel, and a power
socket and a grounding pole on the back panel.
Figure 1-4 Appearance of RG-ES126S-LP

Ruijie RG-ES100 Series Switches Hardware Installation and Reference Guide
Front Panel
Figure 1-5 Front Panel of RG-ES126S-LP
Note:
1. PoE overload LED
2. System status LED
3. Port status LED
4. PoE status LED
5. Port mode switch-over button
6. 10/100Base-TX auto-sensing Ethernet port
7. 10/100/1000Base-T auto-sensing Ethernet port
8. 10/100/1000Base-T combo port
Back Panel
Figure 1-6 Back Panel of RG-ES126S-LP
Note:
1. Grounding pole
2. AC power socket
Heat Dissipation
The RG-ES126S-LP adopts fans for heat dissipation, thereby ensuring normal function of the device in the specified
environment. 10 cm distance space should be reserved at both sides and the back plane of the cabinet to allow air
circulation. It is recommended to clean the device once every 3 months to avoid dust from blocking vents.
LEDs
LED
Panel Identification
State
Meaning
System status LED
PWR
Off
The switch is powered off.
Solid green
The switch is operational.

Ruijie RG-ES100 Series Switches Hardware Installation and Reference Guide
PoE overload LED
PoE-max
Off
The overall PoE output does not reach the
maximum power.
Solid green
The overall PoE output reaches the maximum
power.
RJ45 port status LED
Link/Act
(1-24, 25, 26/26F)
Off
The port is not connected.
Solid green
The port is connected at 10/100/1000 Mbps.
Blinking green
The port is receiving or sending traffic at
10/100/1000 Mbps.
RJ45 PoE status LED
PoE (1-24)
Off
PoE does not supply power.
Solid green
PoE is operational.
1.3 RG-ES110D-P
Technical Specifications
Model
RG-ES110D-P
Ports
8 10/100Base-TX auto-sensing Ethernet ports (Auto MDI/MDIX), and support PoE/PoE+
2 10/100/1000Base-T auto-sensing Ethernet ports (Auto MDI/MDIX)
Power Supply
AC input
Rated voltage range: 100 VAC to 240 VAC
Maximum voltage range: 90 VAC to 264 VAC
Frequency: 50/60 Hz
Rated current: 1.6 A
Adapter output
Rated voltage range: 53.5 VDC
Rated current range: 2.24 A
EEE
Port 1-8: Supported
Port 9-10: Not Supported
PoE
Support PoE and PoE+.
Ports 1-8 are PoE/PoE+-capable with the maximum power output of 30W per port. Ports 9-10
do not support PoE or PoE+.
The overall maximum output power of PoE/PoE+ is 110W.
Power
Consumption
Less than 8W with no PoE load
Less than 129W with PoE full load
Operating
Temperature
0℃to 45℃(32°F to 113°F)