Ruijie RG-S7800C Series Installation and operating manual

RG-S7800C Series Switches
Hardware Installation and Reference Guide V1.11

Copyright Statement
Ruijie Networks©2020
Ruijie Networks reserves all copyrights of this document. Any reproduction, excerption, backup, modification,
transmission, translation or commercial use of this document or any portion of this document, in any form or by anymeans,
without the prior written consent of Ruijie Networks is prohibited.
Exemption Statement
This document is provided “as is”. The contents of this document are subject to change without any notice. Please obtain
the latest information through the Ruijie Networks website. Ruijie Networks endeavors to ensure content accuracy and will
not shoulder any responsibility for losses and damages caused due to content omissions, inaccuracies or errors.

Preface
Thank you for using our products. This manual will guide you through the installation of the device.
This manual describes the functional and physical features and provides the device installation steps, hardware
troubleshooting, module technical specifications, and specifications and usage guidelines for cables and connectors.
Audience
It is intended for the users who have some experience in installing and maintaining network hardware. At the same time, it
is assumed that the users are already familiar with the related terms and concepts.
Obtaining Technical Assistance
Ruijie Networks Website: https://www.ruijienetworks.com/
Technical Support Website: https://ruijienetworks.com/support
Case Portal: http://caseportal.ruijienetworks.com
Community: http://community.ruijienetworks.com
Technical Support Email: [e-mail]
Skype: [e-mail]
Related Documents
Documents
Description
Configuration Guide
Describes network protocols and related mechanisms that supported by the
product, with configuration examples.
Command Reference
Describes the related configuration commands, including command modes,
parameter descriptions, usage guides, and related examples.
Symbol Conventions
Means reader take note. Notes contain helpful suggestions or references.
Means reader be careful. In this situation, you might do something that could result in equipment damage or loss of
data.

Hardware Installation and Reference Guide Product Overview
1
1 Product Overview
Launched by Ruijie independently, RG-S7800C series next generation core switches adopt the crossbar/FULLMESH
architecture and support dual supervisor modules and power supply redundancy.
The RG-S7808C: supports dual supervisor modules and provides six service module slots.
The RG-S7805C: supports dual supervisor modules and provides three service module slots.
The RG-S7810C: supports dual supervisor modules and provides eight service module slots and two switch fabric
slots.
1.1 RG-S7808C
Specifications
Model
RG-S7808C
Module Slot
two supervisor module slots and six service module slots
Supervisor Module
M7800C-CM
Supervisor Module
Redundancy
Supported
Service Module
M7800C-16SFP8XS-EA
M7800C-24SFP/12GT4XS-EA
M7800C-36GT12SFP4XS-EA
M7800C-48GT4XS-EA
M7800C-48GT4XS-P-EA
M7800C-48SFP4XS-EA
Hot Swapping
Supported
Power Supply
Module
RG-PA600I-F: 90-180V~ power: 600W;
180-264V~ power: 600W
RG-PA1600I-F: 90-180V~ power: 1200W;
180-264V~ power: 1600W
RG-PD600I-F: -40- -75V~power: 600W;
RG-PA3000I-PL: 90-176V~ power: 1200W;
176-210V~ power: 2500W;
210-264V~ power: 3000W
RG-PA1600I-PL: 90-176V~ power: 1200W;
176-264V~ power: 1600W
RG-PA800IF: 90-176V~ power: 400W; 176-264V~power: 800W
Power Supply
Redundancy
The power supply redundancy of the same model is supported
Fan Module
M08-FAN
EMC Standards
GB9254-2008 CLASS A, FCC CLASS A
Safety Standards
GB4943-2011
Altitude
Long term operation height: 3000m at 50℃. The temperature decreases by 1℃as the altitude
ranging from 3000m to 5000m increases by 200m.
Operation height: 5000m max
Storage height: 5000m max
Operating
Temperature
0°C to 50°C
Storage
Temperature
-40°C to 70°C
Operating Humidity
10% to 90% RH (non-condensing)
MTBF
216,000 hours
Noise
55.9 dB at 35℃
73.4 dB at 50℃
Weight
Net weight: 32.35 kg (including the chassis and fans)
Dimensions
(W x D x H)
442 mm x 465 mm x 441.7 mm (cable management brackets excluded), 10U

Hardware Installation and Reference Guide Product Overview
2
The weight only includes that of the empty chassis and fans. The whole device's weight is subject to that of the
modules selected.
RG-S7808C switch is a class A product. In a domestic environment, this product may cause radio interference in
which case the user may be required to take adequate measures.
Product Appearance
The hardware system of the RG-S7808C switch is composed of the chassis, the power system, modules and the cooling
system.
The power system provides four power supply slots and supports N+N power redundancy. After M78-PSE or
M78-PSE-L is configured, two PoE power slots are available. PoE power supports 1+1 power redundancy. Users are
recommended to configure redundancy for the power supplies.
The RG-S7808C switch provides two supervisor module slots and six service module slots. The supervisor modules
support 1+1 redundancy. Users are recommended to configure redundancy for the supervisor modules. Users may
choose different service modules as needed.
The cooling system is composed of the fan trays and air filters. Fan trays are at the back of the chassis. The air filters
are on the right side of the chassis.
Figure 1-1 Appearance of the RG-S7808C Switch
Front Panel
The front panel of the RG-S7808C switch is shown in Figure 1-2.
Figure 1-2 Front Panel of the RG-S7808C Switch

Hardware Installation and Reference Guide Product Overview
3
Note:
1. Supervisor module slots
2. Service module slots
3. Cable management bracket
4. Slot for system power supply module
5. Anti-static wrist strap socket
Ensure the supervisor module, service module, and power supply module are removed from the chassis before you
move or transport the RG-S7808C chassis.
Back Panel
The back panel of the RG-S7808C switch is shown in Figure 1-3.
Figure 1-3 Back Panel of the RG-S7808C Switch

Hardware Installation and Reference Guide Product Overview
4
Note:
1. PoE power supply slot
2. Direction sign for installing air filter
3. Captive screw of the air filter
4. Air filter module
5. Fan Tray
6. Handle of the fan tray
7. Captive screws of the fan tray
For S7808C, the PoE power supply slot consists of a frame of PoE power supply module-- M78-PSE. For more
information, please refer to M78-PSE. If PoE power supply input is in demand, you need to purchase a frame so as
to install a PoE power supply module.
Power supply
The RG-S7808C switch adopts both AC and PoE power supply input.
AC power supply input: The RG-PA1600I-F and the RG-PA600I-F power supply modules are supported. The two
types of power supply modules support power management. The supervisor module of the RG-S7808C switch can
read the power supply information and implement flexible and intelligent power management.
PoE power supply input: The RG-PA3000I-PL and the RG-PA1600I-PL power supply modules are supported. The
two types of power supply modules support power management. The supervisor module of the RG-S7808C switch
can read the power supply information and implement flexible and intelligent power management.
The RG-S7808C switch supports N+N power supply redundancy to improve the system stability and reliability. We
recommend users to configure N+M redundancy for power supply modules.
Heat Dissipation System
The operating environment temperature of the RG-S7808C switch ranges between 0 and 50°C . The thermal design must
satisfy the requirement on the device's reliability in the temperature range while ensuring the device's safety and
maintainability. According to the thermal design of the RG-S7808C switch, fans are used to draw air for forced convection
cooling in order to ensure that the device works properly in the specified environment.
Figure 1-4 Ventilation and Heat Dissipation System of the RG-S7808C Switch (Air Intakes)
Note:
1. Air intakes for PoE power modules
2. Air intakes for service and supervisor modules
3. Air intakes for system power modules
Figure 1-5 Ventilation and Heat Dissipation System of the RG-S7808C Switch (Exhaust Vents)

Hardware Installation and Reference Guide Product Overview
5
Note:
1. Exhaust vents for PoE power modules
2. Exhaust vents for service and supervisor
modules
3. Exhaust vents for system power modules
For the PoE power supply modules, air flows across the chassis from the back intakes to the front vents.
For the supervisor and service modules, air flows across the chassis from the right intakes to the back vents.
For the power supply modules, air flows in from the front intakes and out from the back vents.
The chassis should be mounted in a place with sufficient space for air circulation. Maintain a minimum clearance of
10cm around the chassis.
If any module slot is unoccupied, install a filler panel to ensure proper airflow.
1.2 RG-S7805C
Specifications
Model
RG-S7805C
Module Slot
two supervisor module slots and three service module slots
Supervisor Module
M7805C-CM
Supervisor Module
Redundancy
Supported
Service Module
M7800C-24SFP/12GT4XS-EA
M7800C-36GT12SFP4XS-EA
M7800C-48GT4XS-EA
M7800C-48SFP4XS-EA
M7800C-24GT24SFP4XS-EA
Hot Swapping
Supported
Power Supply
Module
RG-PA300I-F: 90-290V~ power: 300W;
192-290V~ power: 300W
Power Supply
Redundancy
The power supply redundancy of the same model is supported.
Fan Module
M05C-FAN
EMC Standards
GB9254-2008 CLASS A, FCC CLASS A
Safety Standards
GB4943-2011

Hardware Installation and Reference Guide Product Overview
6
Altitude
Long term operation height: 3000m at 50℃. The temperature decreases by 1℃as the altitude
ranging from 3000m to 5000m increases by 200m.
Operation height: 5000m max
Storage height: 5000m max
Operating
Temperature
0°C to 50°C
Storage
Temperature
-40°C to 70°C
Operating Humidity
10% to 90% RH (non-condensing)
MTBF
200,000 hours
Noise
64.3 dB at 35℃
70.3 dB at 50℃
Weight
Net weight: 12.42 kg (including the chassis and fans)
Dimensions
(W x D x H)
442 mm x 451 mm x 175 mm (cable management brackets excluded), 4U
The weight only includes that of the empty chassis and fans. The whole device's weight is subject to that of the
modules selected.
RG-S7805C switch is a class A product. In a domestic environment, this product may cause radio interference in
which case the user may be required to take adequate measures.
Product Appearance
The hardware system of the RG-S7805C switch is composed of the chassis, the power system, modules and the cooling
system.
The power system provides two power supply slots and supports 1+1 power supply redundancy. Users are
recommended to configure redundancy for the power supplies.
The RG-S7805C switch provides two supervisor module slots and three service module slots. The supervisor
modules support 1+1 redundancy. Users are recommended to configure redundancy for the supervisor modules.
Users may choose different service modules as needed.
The cooling system is composed of the fan trays. Fan trays are at the back of the chassis.
Figure 1-65 Appearance of the RG-S7805C Switch
Front Panel
The front panel of the RG-S7805C switch is shown in Figure 1-7.
Figure 1-7 Front Panel of the RG-S7805C Switch

Hardware Installation and Reference Guide Product Overview
7
Note:
1. Supervisor module slot
2. Service module slots
3. Cable management bracket
4. Anti-static wrist strap socket
Ensure the supervisor module, service module, and power supply module are removed from the chassis before you
move or transport the RG-S7805C chassis.
Back Panel
The back panel of the RG-S7805C switch is shown in Figure 1-8.
Figure 1-8 Back Panel of the RG-S7805C Switch
Note:
1. Power module slot
2. Fan tray
3. Handle of the fan tray
4. Captive screws of the fan tray
Power supply
The RG-S7805C switch adopts the AC power supply.
AC power supply input: The RG-PA300I-F and the RG-PA460I-F power supply modules are supported. The two
types of power supply modules support power management. The supervisor module of the RG-S7805C switch can
read the power supply information and implement flexible and intelligent power management.
Heat Dissipation System
The operating environment temperature of the RG-S7805C switch ranges between 0 and 50°C . The thermal design must
satisfy the requirement on the device's reliability in the temperature range while ensuring the device's safety and
maintainability. According to the thermal design of the RG-S7805C switch, fans are used to draw air for forced convection
cooling in order to ensure that the device works properly in the specified environment.
Figure 1-9 Ventilation and Heat Dissipation System of the RG-S7805C Switch (Air Intakes)