Ruijie RG-S6000C-48GT4XS-E-AC DCN Installation and operating manual

Ruijie RG-S6000C-48GT4XS-E-AC(DCN) Switch
Hardware Installation and Reference Guide

·
Copyright Statement
RuijieNetworks©2021
RuijieNetworks reserves allcopyrights ofthis document.Any reproduction,excerption, backup,modification,
transmission, translation or commercial useof this document or anyportion of this document, in anyform orbyanymeans,
withoutthe prior writtenconsentof Ruijie Networks is prohibited.
Exemption Statement
This document is provided “as is”. The contents of this do cumentare subjecttochange without anynotice. Please obtain
the latestinformation through theRuijie Networks website. Ruijie Networks endeavors to ensure contentaccuracyand will
not shoulderanyresponsibilityfor losses and damages causeddue tocontentomissions,inaccuraciesorerrors.

·
Preface
Thank you for usingourproducts.This manualwillguideyouthroughtheinstallationofthe device.
This manualdescribesthe functionalandphysicalfeatures andprovides the device installationsteps,hardware
troubleshooting,moduletechnicalspecifications,andspecifications andusageguidelines forcables and connectors.
Audience
It is intended for the users who have some experience in installing and maintaining network hardware.At the same time,
it is assumedthatthe users arealreadyfamiliarwiththe related terms andconcepts.
Obtaining Technical Assistance
RuijieNetworks Website:https://www.ruijienetworks.com/
TechnicalSupportWebsite:https://ruijienetworks.com/support
CasePortal:http://caseportal.ruijienetworks.com
Community:http://community.ruijienetworks.com
TechnicalSupportEmail:[e-mail]
Skype: [e-mail]
Related Documents
Documents
Description
Configuration Guide
Describes networkprotocolsand relatedmechanismsthatsupported bythe
product, with configurationexamples.
Command Reference
Describes therelatedconfigurationcommands,includingcommandmodes,
parameterdescriptions,usageguides,and relatedexamples.
Symbol Conventions
Means readertake note. Notes contain helpfulsuggestionsorreferences.
Means readerbe careful. In this situation,you mightdo somethingthatcouldresultinequipmentdamage
or loss ofdata.

Hardware Installation and Reference Guide Product Overview
4
1 Product Overview
RuijieRG-S6000C-48GT4XS-E-AC(DCN)IPv6 switchsupports high-density10G port scalability,mainlyappliedtodata
center scenarios.RG-S6000C-48GT4XS-E-AC(DCN)switch provides aggregationandaccessservicesforservers with
10G ports.
Model
10/100/1000
Base-T
Ethernet
Port
1000M
SFP
Port
10G SFP+
Port
MGMT
Port
USB
Port
Mini
USB
Port
Console
Port
Expansion
Module
Slot
RPS
RG-S6000C-
48GT4XS-E-
AC(DCN)
48
N/A
4
1
1
1
1
1
Dual
SFP+ port supports both10Gbase-Rand 1000base-X.
The RG-S6000C-48GT4XS-E-AC(DCN)switchhas the following external ports:
MGMT port:This port is a 10/100/1000Mmanagementport.It is usedto connectwith an Ethernet port of a PC to
perform program.It also supports DataCenter ManageabilityInterface (DCMI) protocol, and users can do remote
managementand maintenance forthe switchthrough the port. Usestandardnetworkcables whenthe port is
connected with an Ethernet port.
USB port: The UniversalSerial Bus (USB) port is used to connectwith USB memoryto save logs,mainframe
versions,warnings and otherdiagnosticmessages.
Console port:This port applies RS-232 interfaceelectrical levelandstandardRJ45 connectors.It is usedto
connectthe serialports of the terminal PCto perform tasks includingsystemcommissioning,configuration,
maintenance,management,andsoftwareloading.
Mini USB port: This port canbe usedas a serial portfor installingthesoftware driver.For detail,see AppendixF.
The RG-S6000C-48GT4XS-E-AC(DCN)switchsupports bothConsole andMiniUSB ports to conduct
commissioning,configuration,maintenance,management,andsoftwareloading.However,thesefunctions
are activated on onlyoneof them at a particulartime.
RG-S6000C-48GT4XS-E-AC(DCN)switchis a class Aproduct.In a domesticenvironment,this product
maycauseradiointerference inwhichcasethe usermaybe requiredto take adequate measures.
1.1 RG-S6000C-48GT4XS-E-AC(DCN)
Technical Specifications
Model
RG-S6000C-48GT4XS-E-AC(DCN)
CPU
Dual-corewith each1.0 GHz

Hardware Installation and Reference Guide Product Overview
5
BOOTROM
8 MB
Flash Memory
512MB
SDRAM
1 GB
Optical Module
See AppendixB.
The supported module typemay change at anytime. ConsultRuijieNetworksfor
the latestinformation.
Expansion Module
Slot
1 slot
Supportedexpansionmodule:M6000E-04XS
Fan Module Slot
1 slot
Supportedexpansionmodule:M6000E-FAN-F
PowerModule
Slot
2 slots
Supportedpowermodule:RG-PA70I
AC input:
Rated voltage: 100 V to 240 V
Maximum voltage: 90V to 264V
Frequency: 50/60 Hz
Ratedcurrent per input:2 A
HVDC input:
Rated voltage: 120 V to 340 V
Maximum voltage: 110 V to 380 V
Ratedcurrent per input:2 A
-48 lowvoltage DC input:
Ratedvoltage: -48V to -78 V
Maximum voltage: -48V
Maximum Rated currentper input: 3.15 A
SFP+ Port
10GBase-R
1000Base-X
Power
Consumption
<60 W (with fan tray but without expansionmodules)
Temperature
Operatingtemperature:0ºC to 50ºC (32 ºF to 122ºF)
Storagetemperature:-40ºC to 70ºF (-40ºC to 158ºF)
Humidity
Operatinghumidity:10% to 90%
Storagehumidity: 5% to 95%
Temperature
Alarm
Supported
EMI Standard
GB9254-2008CLASSA
SafetyStandard
GB4943-2011
Dimensions
(W x D x H)
440mmx 300mmx 44mm (17.32 in.x 11.81 in. x 1.73 in.)
Weight
4.8 kg (10.58lbs )
Product Appearance

Hardware Installation and Reference Guide Product Overview
6
The S6000C-48GT4XS-E-AC(DCN) Ethernetswitch provides 48 10/100/1000Base-T Ethernet ports, 4 10GE SFP+ ports,
1 MGMT port,1 USB port, 1 Mini USB port, and 1 Consoleportonthe front panel,as wellas 2 power module slots,1
expansion moduleslotand1fan moduleslotonthe backpanel.
Figure1-1 Appearanceof RG-S6000C-48GT4XS-E-AC(DCN)
Front Panel
Figure1-2 Front Panel of RG-S6000C-48GT4XS-E-AC(DCN)
Note:
1. System status LED
2. Power status LED (PWR1)
3. Power status LED(PWR2)
4. MGMT port status LED
5. Fan status LED
6. Consoleport
7.10/100/1000Base-TEthernetport
8. Switch port status LED
9. USB port
10. Mini USB port
11. MGMT port
12. 10GE SFP+ port
Back Panel
Figure1-3 Back Panel of RG-S6000C-48GT4XS-E-AC(DCN)

Hardware Installation and Reference Guide Product Overview
7
Note:
1. Grounding connector
2. Expansion moduleslot
3. Fan module slot
4. Power module slot1
5. Power module slot2
Power Supply
The RG-S6000C-48GT4XS-E-AC(DCN)supports twopowermodules.Fordetails,seethe section “PowerModules”.
Dual-power input: The switch can bepowered byonepowermodule, or twopowermodules. When both twomodules are
available,the switchis poweredincurrent sharing mode.
When the switchis poweredbythe dual-powermodules,ifthe system workingpower is greaterthanthe
capacityof singlepowermodule,powerredundancycannotwork; if one powermodulefails,the switch
system willbeaffected.
Heat Dissipation
RG-S6000C-48GT4XS-E-AC(DCN) adopts front and back fans forheat dissipation, therebyensuring the normal function
of the device in the specifiedenvironment.Maintainaminimumclearanceof100mm (3.94in.)aroundthe cabinetto
allowaircirculation.
Figure1-4 Flow SchemeofHeat Dissipation
LED

Hardware Installation and Reference Guide Product Overview
8
LED
Panel Identification
State
Meaning
System status LED
Status
Off
The switchis not receivingpower.
Blinkinggreen
(3 Hz)
The switchis beinginitialized with3Hz blinking.
Continuous blinkingindicates errors.
Blinkinggreen
(10Hz)
Supports remoteon/offto locate the switch.
Solidgreen
The switchis operational.
Solidyellow
Temperature alarm:
1. Temperature of inlet/outletair exceeds the
normaloperatingtemperature range.
2. The powersupplies cannotsupportthe whole
system.
Check the working environment of the switch and
powersuppliesimmediately.
Solidred
The switchis faulty. For details,seethe chapter
“Troubleshooting”.
Powerstatus LED
PWR1/PWR2
Off
The power module is not in place or not receiving
power.
Solidgreen
The powermoduleis connectedand cansupply
power.
Solidred
The redundantpoweris faulty or the AC power
cord is not connected.
Solidyellow
The powermodulecannotbeidentified.
MGMT port status
LED
MGMT
Off
The port is not connected.
Solidgreen
The port is connected at 1000 Mbps.
Blinkinggreen
The port is receiving or transmitting traffic at
1000Mbps.
Solidyellow
The port is connected at 10/100Mbps.
Blinkingyellow
The port is receiving or transmitting traffic at
10/100 Mbps.
Fan status LED
FAN
Off
The fan moduleis notinplace or not receiving
power.
Solidgreen
The fans are inplaceand are operational.
Solidyellow
One fan is faulty, but the heat dissipation
requirementcanbemet.
Solidred
Two or morefans arefaulty, andthe heat
dissipationrequirementcannotbe met.
10GE SFP+ port
status LED
49F-52F
Off
The port is not connected.
Solidgreen
The portis connected at 1/10 Gbps.
Blinkinggreen
The portis receiving or transmitting traffic at 1/10
Gbps.
10/100/1000Base-T
1-48
Off
The port is not connected.

Hardware Installation and Reference Guide Product Overview
9
LED
Panel Identification
State
Meaning
Ethernet port status
LED
Solidgreen
The port is connected at 1000 Mbps.
Blinkinggreen
The port is receiving or transmitting traffic at
1000Mbps.
Solidyellow
The port is connected at 10/100 Mbps.
Blinkingyellow
The port is receiving or transmitting traffic at
10/100 Mbps.
1.2 ExpansionModules
The RG-S6000C-48GT4XS-E-AC(DCN)switchsupports thefollowing module:M6000E-04XS.
Module
Description
External port
M6000E-04XS
4-port 10GE opticalmodule
4 SFP+ ports
For the detaileddescription aboutthis module,seeSwitchExtensionModule Manual.
1.3 PowerModules
At present,the RG-S6000C-48GT4XS-E-AC(DCN) switchsupports the swappable RG-PA70Ipowermodule and
RG-PD70I power module. The RG-PA70I power module provides AC input and DC output, 12V voltage output and up to
70W poweroutputto the switch.
1.3.1 RG-PA70I Power Module Specification
Model
RG-PA70I (AC input)
RG-PA70I (HVDC input)
Rated Voltage
100V to 240V
50/60Hz
120V to 340V
Maximum Voltage
90 V to 264 V
47/63Hz
110V to 380V
Max Current Input
2 A
Output Voltage
12 V
Max Current Output
5.83 A
Max PowerOutput
70 W
Input Leakage
Current
≤1.75 mA
Dimensions
(W x D x H)
50.5 mmx156 mmx38 mm(1.99 in. x 6.14 in. x 1.50 in. )
Weight
0.395kg (0.87 lbs)
Temperature
Operatingtemperature:-10ºC to 50 ºC (14 ºF to 122ºF)
Storagetemperature:-40ºC to 70 ºC (-40 ºF to 158 ºF)
Humidity
Operatinghumidity:10% to 90%
Storagehumidity: 5% to 95%

Hardware Installation and Reference Guide Product Overview
10
Altitude
Operatingaltitude:0 m to 5,000 m
Storagealtitude:0 m to 10,000 m
Features
Feature
Description
Conformal Coating
Protects circuits againstmoisture, frog,mould, electrical shock and leakage, andso on.
Protection
Provides protectionover over-voltage/current input/output,short-circuitoutputand so
on.
I2C Communication
Allows the mainframetocommunicatewiththe powermodulebyI2C.
PowerSupplyRedundancy
Supports dualpowermodulestocooperate inparallel,enabling PEwith1+1
redundancyandredundantpowersupplieswithcurrentsharing.
Hot Swapping
Supports to disconnectoneredundantpowermodulefrom theoutsidepowersupply
system,plugandunplug powermoduleswhile thedevice is powered on.
PowerSupplyAlarm
Monitors powersupplystatus andgenerates alarmsthroughthepowerstatus LED.
LED
LED
Panel Identification
State
Meaning
Status LED
DC OK
Off
There is no poweroutput or an error occurs.
Solidgreen
The moduleis operational.
1.3.2 RG-PD70I Power Module Specification
Model
RG-PD70I
Rated Voltage
DC input:-36 V to -72V
Max Current Input
3.15 A
Output Voltage
12 V
Max Current Output
5.83 A
Max PowerOutput
70 W
Dimensions
(W x D x H)
50.5 mmx156 mmx38 mm(1.99 in. x 6.14 in. x 1.50 in.)
Weight
0.385kg (0.85 lbs)
Temperature
Operatingtemperature:-10ºC to 50 ºC (14 ºF to 122ºF)
Storagetemperature:-40ºC to 70 ºC (-40 ºF to 158 ºF)
Humidity
Operatinghumidity:10% to 90%
Storagehumidity: 5% to 95%
Altitude
Operatingaltitude:0 m to 5,000 m
Features
Feature
Description
Conformal Coating
Protects circuits againstmoisture, frog,mould, electrical shock and leakage, andso on.
Protection
Provides protectionover over-voltage/current input/output,short-circuitoutputand so
on.
I2C Communication
Allows the mainframetocommunicatewiththe powermodulebyI2C.
PowerSupplyRedundancy
Supports dualpowermodulestocooperate inparallel,enabling PEwith1+1
redundancyandredundantpowersupplieswithcurrentsharing.
Hot Swapping
Supports to disconnectoneredundantpowermodulefrom theoutsidepowersupply

Hardware Installation and Reference Guide Product Overview
11
system,plugandunplug powermoduleswhile the device is powered on.
PowerSupplyAlarm
Monitors powersupplystatus andgenerates alarmsthroughthepowerstatus LED.
LED
LED
Panel Identification
State
Meaning
Status LED
OUT
Off
There is no poweroutput or an error occurs.
Solidgreen
The moduleis operational.
1.4 FanModule
The M6000E-FAN-F fan moduleprovides good heatdissipationsystemtoensure stableoperationforthe RG-S6000E
switch.M6000E-FAN-F supports speedregulation,hotswappingand faultalarm.
Specification
Model
M6000E-FAN-F
Number of Fans
3
Max RPM
18000RPM perfan tray (One M6000E-FAN-F fan moduleprovides threefan trays.)
Power Consumption
<20 W
Weight
0.375kg (0.83 lbs)
Dimensions
(W x D x H)
150mmx 100mmx 40 mm(5.91 in. x 3.94 in. x 1.57 in.)
Features
Features
Description
Protection
Provides overcurrent protection.
N+1 Redundancy
Provides three fan trays to ensurenormal runningoftheswitchwhenonefan tray fails
to work.
Speed Regulation
Supports intelligentspeedregulation.
Hot Swapping
Supports fanmodulereplacementwhilethe device is poweredon.
LED
LED
Panel Identification
State
Meaning
Status LED
Status
Off
Fan moduleis notconnected.
Solidgreen
Fan moduleis operational.
Solidred
Fan moduleis faulty.

Hardware Installation and Reference Guide Preparation before Installation
12
2 Preparation before Installation
2.1 SafetySuggestions
To avoid personalinjuryandequipmentdamage,pleasecarefullyreadthe safetysuggestions beforeyouinstallthe
RG-S6000C-48GT4XS-E-AC(DCN)switch.
The followingsafetysuggestionsmaynotcover all possibledangers.
2.1.1 Installation
Keepthe chassis cleanandfree from dust.
Do notplacethe equipmentinapassage.
Do not wearloose clothes oranyother things that maybecaught by the chassisduring installationand
maintenance.
Turn off all powersuppliesand removethe powersockets andcables beforedismantling thecabinet.
Avoid transferring theequipmentwithoutpackage.
If stacking is required during transportation, the numberof stacked layers should not exceed the numbermarked on
the packagingbox. Do notplace the box upsidedownoronthe side.
The mainframescannotbestacked directly. Each mainframe should be separated bypacking pads and placed
rightsideup.The numberofstackinglayers shouldnotexceed 3 (the stackingheightcannotexceed 1M). The
packingpads need tobe placed in a stablealignment.
2.1.2 Movement
Do notfrequentlymovethe device.
Whilemovingthe device, keep its balanceandavoidyour legs,feet andback from beinghurt.
Before moving the device, turn off all powersupplies anddismantle allpowermodules.
2.1.3 Electricity
Observe localregulations andspecifications whenperforming electricoperations.Relevantoperators mustbe
qualified.
Carefullycheckany potentialdangerinthe working area,suchas ungroundedpowersupply,unreliablegrounding
of the powersupply, anddamp/wetgroundorfloor.
Find out the locationof the emergencypowersupplyswitchinthe room before installation.Firstcut off the power
supplyin the caseof anaccident.
Do nomaintainthe switch that is powered-onalone.
Make surethat the poweris turned off whennecessary.
Do not place the equipmentina damp place.Do not let any liquid enterthe chassis.
Any non-standardandimpropriate electricoperations maycause anaccidentsuchas a fire or electrical
shock,thus causingsevere even fatal damagetohumanbodiesand equipment.

Hardware Installation and Reference Guide Preparation before Installation
13
Direct or indirecttouch througha wet objecton high-voltageand commercialelectricitymaybringa fatal
danger.
If a powersupplysystem is equippedwithaleakageprotector(alsoreferred to as "leakage currentswitch"
or "leakagecurrentbreaker"),the rated leakageactioncurrentof each leakageprotectoris greaterthan
twice ofthe theoretical maximum leakagecurrentofallthe powersuppliesin thesystem.For example,if a
system is equipped with eight identicalpowersupplies, the leakage current of each powersupplyis equal to
or less than3mA, andthe leakagecurrent ofthe system totals 24mA. A leakage protectorwith 30 mA
rated action currentsupports lessthanfive powersupplies(thatis,Action currentof the leakage
protector/2/Maximum leakagecurrentof each powersupply= 30/2/3 = 5). In other words,the leakage
protector with 30 mArated action current supports no more than four power supplies. In this case,the eight
powersuppliesinthe system require at leasttwo leakage protectors with30 mArated action current and
each leakage protectorsupports fourpowersupplies.If powersuppliesina system differin models,the
rated leakageactioncurrentof eachleakageprotectordividedby two is greater than the sum ofmaximum
leakagecurrents ofall the powersupplies.Therated leakagenon-actioncurrentof a leakageprotector
shallbe 50%of the leakageactioncurrent. Take a leakageprotectorwith 30 mArated leakageaction
current as anexample.The rated leakage non-actioncurrentshallbe15 mA. Whenthe leakagecurrent is
below15mA, the protector shallnotact. Otherwise,misoperation mayeasilyoccurdueto highsensitivity
andthus the leakageprotector trips,devices are poweredoff, andservices are interrupted.
To guaranteepersonalsafety,the rated leakageactioncurrentof each leakageprotectorin the system
mustbe equal to or less than 30mA(human bodysafetycurrent is 30 mA). When twice of the total leakage
currentof the system is greaterthan 30mA, the system mustbeequippedwithtwo or moreleakage
protectors.
For the leakagecurrentvalue of eachpowersupplymodel,see thepowersupplymodelparametertablein
Chapter1.
2.1.4 ESD
To prevent ElectronicStatic Discharge (ESD),pay attention to the following:
Connectthe device's circuitto the ground.
Clearup the dust.
Maintain the properhumidity.
2.1.5 Laser
Among the modules supported bythe RG-S6000C-48GT4XS-E-AC(DCN),manyare Class Ilaserproducts.Therefore,
pay attentionto the followingwhenusingthem:
When a fibertransceiverworks,ensurethat the port has beenconnectedwithan opticalfiber or is covered witha
dustcap, to keep outdustandavoid burningyour eyes.
Do notstareintothe opticalports.

Hardware Installation and Reference Guide Preparation before Installation
14
Do not approachorstare into any optical port,as this maycausepermanentdamagetoyour eyes.
2.2 InstallationSite Requirements
The RG-S6000C-48GT4XS-E-AC(DCN)switchmustbeusedindoors.Toensureits functioningand prolongits service
life, the installation site mustmeetthefollowingrequirements.
2.2.1 Ventilation
Maintain a minimum clearance of100mm (3.94in.) aroundthe cabinetto allowaircirculation.Cables shouldbe
bunchedorput on the cableframeafter beingconnectedin orderto prevent blockingthe air intake.
2.2.2 Temperature and Humidity
The temperatureandhumidityinthe room mustbestableto ensurethedevice's properfunctioningand prolongits
service life.
Continuous impropertemperature andhumiditywillcausedamagetothe device.
High relative humiditywill reduce the insulation of insulationmaterials and cause electricleakage. Sometimes itmaylead
to changes inthe mechanicalcharactersofmaterials and rustmetalcomponents.
Lowrelative humiditywilldry the insulationsheetsandgeneratestaticelectricity,which willdamagetheelectric circuits
of the device.
Hightemperature willlargeaffect the device's reliability, shorten its servicelifeand accelerateits aging.
Temperature andhumidityrequirements ofthe RG-S6000C-48GT4XS-E-AC(DCN)switchare as follows:
Temperature
Relative Humidity
0 ºC to 50ºC(32 ºC to 122ºC )
10%to 90%
The workingtemperature andhumidityaremeasured1.5 m abovethe groundand0.4 m away from the
front plat andwhenthe chassis’ frontandrearprotective plates are removed.
2.2.3 Cleanness
Dustposes thetopthreat to the running of the equipment.The indoordustfallingon the equipmentmaybe adheredby
the staticelectricity, causingbad contactof the metallicjoint.Such electrostaticadherencemayoccurmoreeasilywhen
the relative humidityis low,not onlyaffecting the uselifeof the equipment,butalsocausingcommunicationfaults.The
followingtableshows the requirementsforthe dustcontentand granularityin the equipmentroom.
Substance
Concentration Limit(particles/m3)
Dustparticles (diameter ≥0.5μm)
≤3.5×106
Dustparticles (diameter ≥5μm)
≤3×104
Apart from dust, the salt,acidand sulfidein the airin the equipmentroom mustalsomeetstrictrequirements;as such
poisonoussubstancesmayacceleratethecorrosionofthe metalandthe aging ofsome parts.The equipmentroom

Hardware Installation and Reference Guide Preparation before Installation
15
shouldbeprotectedfrom the intrusion ofharmful gases (forexample, SO2, H2S, NO2and Cl2), whose requirements are
listedinthe followingtable.
Gas
Average (mg/m3)
Maximum (mg/m3)
SO2
0.3
1.0
H2S
0.1
0.5
NO2
0.5
1.0
Cl2
0.1
0.3
2.2.4 Grounding
A good groundingsystem is the basis forthestableand reliableoperationofthe RG-S6000C-48GT4XS-E-AC(DCN)
switch,preventinglightningstrokeandresistinginterference.Pleasecarefullycheckthe groundingconditionson the
installationsite accordingtothe groundingrequirements,and perform groundingoperations properlyas required.
The correct connectionof grounding lines guaranteesthe lighting and interferenceresistance ofswitches
andmustbeperformedwithprecision.
SafetyGrounding
The equipmentusing ACpower supplymustbe groundedbyusing theyellow/green safetygroundingcable.Otherwise,
whenthe insulatingresistancedecreasesthe powersupplyand theenclosureinthe equipment,electricshockmay
occur.
Lightning Grounding
The lightningprotectionsystem ofa facility is an independentsystem thatconsists ofthelightningrod, downlead
conductorandthe connector to the groundingsystem,whichusuallysharesthe powerreferenceground and
yellow/green safetycableground.The lightning discharge groundis forthe facilityonly, but unnecessaryfor equipment.
EMC Grounding
The groundingrequiredforEMC designincludes shielding grounding,filtergrounding,noiseand interference
suppression,andlevelreference.All the above constitutethe comprehensivegroundingrequirements.The grounding
resistance should be less than 1Ω. The RG-S6000Eback panelhas onegrounding connector.
Figure2-1 Groundingofthe RG-S6000E

Hardware Installation and Reference Guide Preparation before Installation
16
2.2.5 Lightning Resistance
When the AC powercableis importedoutdoors anddirectlyconnectedto the powerport ofthe switch,lightning
preventingwires shouldbeadoptedtoprevent the switchfrom beinghitby lightningshocks.Thelightningpreventing
wires canbe fixed on the cabinet, workstation,or the equipmentroom’swallthroughlinebucklesandscrews.In
applications,theAC current firstenters the lightningpreventingwires and thenthe switch.
The lightningpreventingwires are not providedandshouldbepurchasedbyusers as required.Forthe
usageoflightningpreventingwires,refer to their manuals.
2.2.6 EMI
All kinds ofinterference,from insideoroutsideofthe device or applicationsystem,createimpacts onthedevice by
transmissionofcapacitycoupling,inductancecouplingandelectromagneticwaves.
Electromagneticinterferencecan bedivided into two categories bytransmissiontypes, namelyi.e. radiatedinterference
andconducted interference.
Power,normallyRF power,transmitted from adevice throughspaceto a sensoris calledradiatedinterference.The
origin of the interference source can eitherbe part of or a unit separated electricallyfrom the interferedsystem.
Conductedinterferenceis transmitted throughmagneticwiresorsignalcablesfrom the source origintosensors.
Generally, conducted interference affects the powersupplyof a device and can be controlled bya wave filter. Given that
radiated interference caninterrupt anysignal paths of the device, it is difficultto shield the device from such interference.
The AC powersupplying system is theTN system.The single-phasethree-wire socketwithprotectinggrounding
mustbe used as thesocket for the powersupplyto enable the device’s upper filter circuit to effective filter the power
interface.
The switchshouldbe farfrom high-powerradiotransmitting stations,radarstations andhigh-frequencyand
large-currentdevices.
Electromagneticshielding methods shouldbeappliedwhennecessary,such as usingtheshieldedcableas the
interfacecable.
Cables mustbeconnectedto interfaces inside theroom toprevent damagetothe device’s signalports causedby
over-voltage and over-current generatedbythunderand lightning.
2.3 PrecautionsforFiberConnections
Before you connect the fibers,check that the opticalconnectortype and fiber type matchthe opticalinterface type used.
In addition, payattention to the Txand Rxdirections of the fiber. The Txend of this device should be connected to the Rx
endof the peerdevice, and the Rx endof this device to the Tx endof the peer device.
2.4 InstallationTools
List of Installation Tools
Common Tools
Phillips screwdriver,flat-headscrewdriver,relatedelectriccables and opticalcables,
bolts,diagonalpliers,straps
Special Tools
Anti-static tools
Meters
Multimeter

Hardware Installation and Reference Guide Preparation before Installation
17
RG-S6000Eis not providedwith a tool kit. Pleaseprepare tools onyourown.
2.5 Inspection afterUnpacking
Packing Items
Mainframe Box
Mainframe,grounding wire,quickstart guide,packing list,other materials
Module Box
Module, quickstart guide,packing list
A normal delivery should contain the above mentioned items, whichmaydiffer from the actual delivery,
depending on purchase contracts. Please check your goods carefullyagainst the packing list or purchase contract.
If you have any questionsorthereare any errors,pleasecontactyour distributor.
Unpacking Procedure
Step 1: Cut off the packingstraps on theshipping boxwithscissors,place theboxon a flatsurface with the rightdirection
facingup, and checkwhether the sealon the top ofbox is intact.
Step 2: Use a papercutter to cutthe tapes alongthe joints betweenthesides andonthetop of the box, andopenthe
shippingbox.
The insidefoam mayvary withproduct.
Step 3: Take out the accessorybox, verify that the maininstallation accessories arenotmissing,andthenput the
accessoryboxaside.
The accessories mayvary withproduct.
Step 4: Place the mainframewiththepanel foam facing upwards.
Step 5: Remove the panelfoam and setit aside.
Step 6: Move the mainframe with bothhands ontotheshippingboxof anotherproduct,and removethe foam on the
other side.
Step 7: Remove the tapeon the top ofthe antistaticbag, open and reach into the bag withboth hands, grab themiddle of
the two sides ofthe mainframe,lift the mainframeoutofthe antistaticbag,and placeit on an antistaticworkingbench.
Step 8: Push the powersupplyinwardto ensure it can work with the mainframe.

Hardware Installation and Reference Guide Product Installation
18
3 Product Installation
Pleaseensurethatyou have carefullyreadChapter2 andmake surethat the requirements setforthin
Chapter2 have beenmet.
3.1 Installation Flowchart
3.2 Pre-installation Confirmation
Before installation,pleaseconfirm the followingpoints:
Whether sufficientairflowis availablefor the switch
Whether the requirements ofthe switchfor temperature andhumidityare met
Whether powercables are alreadylaidout and whetherthe requirements ofelectricalcurrentare met
Whether relatednetworkcables arealreadylaid out

Hardware Installation and Reference Guide Product Installation
19
3.3 Installing the Switch
Precautions
Duringinstallation,notethe followingpoints:
Connectthe powercables of differentcolors to the correspondinggroundingposts.
Ensurethat the connectedpowercables have soundcontact.
Do not placeheavy items onthe switch.
Maintain a minimum clearanceof100mm (3.94in.) aroundthe cabinetto allowaircirculation.Do not stackthe
devices.
The switchshould be located far awayfrom the largepowerradiolaunch pad, radarlaunch pad, and
high-frequencylarge-current devices. If necessary, electromagneticshieldingshould be adopted. For example, use
interfacecables to shieldcables.
Interface cables shouldbelaidinsidetheequipmentroom.Outdoorcablingis prohibited,avoidingdamagesto
device signal interfaces caused byover-voltage or over-current of lightning.
3.3.1 Mounting the Switch in a Standard 19-inch Rack
The RG-S6000C-48GT4XS-E-AC(DCN) switch follows the EIAstandard dimensions and can be installed in 19-inch rack.
Duringthe installation,placethefront panel ofthe switchto the rack. For safety purposes,screwup thedistributed
screws as showninthe3-1.
Figure3-1 Attaching the Mounting Bracket to the Switch
3.3.2 Mounting the Switch on the Wall
The RG-S6000C-48GT4XS-E-AC(DCN) switch can bemounted ona wall with the suppliedmounting brackets, as shown
in Figure 3-2.
Figure3-2 Attaching the Mounting Brackets to the Switchfor Wall-Mounting

Hardware Installation and Reference Guide Product Installation
20
3.3.3 Mounting the Switch on a Table
For often, users maynothave a 19-inch rack.Thus,it is commonto mountthe switchonthe workbench with 2 simple
steps:
Attach the four rubberfeet to the recessedareas onthebottom of the switch.
Placethe switchon the tableand keepgoodventilation.
3.4 Installing andRemovingthe FanModules
Wear anti-staticgloves beforethe followingoperations.
Installing an M6000E-FAN-F Fan Module
Step 1: Take a new fan moduleoutof the package.
Step 2: Holdthe captive screws onthe fan module, andtheninsertthe fan modulealongtherailuntil it is fullyinserted
andstays in good contact with the slot.
Step 3: Tighten the captive screws with a screwdriverto fix the moduleintheswitchchassis.
Figure3-1 Installing M6000E-FAN-F