Russell hobbs Rhc410 Installation instructions manual

RHC410_IB_FA_150421 Part No. T22-9002131

HAND HELD

STEAMER SUPREME

2 YEAR WARRANTY

INSTRUCTIONS & WARRANTY

MODEL RHC410

IMPORTANT SAFEGUARDS

When using this appliance, basic safety precautions should always be followed, including the following:

Read all instructions before, and follow whilst using this appliance.

1. To protect against electrical hazards, do not immerse the power cord, plug or steamer in water

or any other liquid.

2. Do not use outdoors or in damp or moist areas.

3. Do not touch hot surfaces, always use the appliance handles.

4. Care should be taken when using the appliance due to emission of steam.

5. This appliance is not intended for use by persons (including children) with reduced physical, sensory

or mental capabilities, or lack of experience and knowledge, unless they have been given supervision

or instruction concerning use of the appliance by a person responsible for their safety.

6. This appliance must be attended whilst plugged in.

7. Ensure the steamer is standing on its heel and with the soleplate clear of any surrounding objects when

switching on.

8. Ensure the handheld steamer is unplugged during ﬁlling and emptying.

9. Always turn off and unplug from the wall power outlet when not in use.

10. To avoid possible burns, ensure the appliance is off and has cooled before cleaning.

11. To disconnect, turn off the wall power outlet, then grasp and pull the plug from the wall outlet. Never

pull by the cord.

12. Do not operate this appliance with a damaged cord/plug or after the appliance has been

dropped, is leaking, damaged or has malfunctioned in any manner.

Contact Customer Service for examination, adjustment, repair or replacement.

13. There are no user serviceable parts. If repairs are required, they must be performed by the

manufacturer or a suitably qualiﬁed person in order to avoid a hazard.

14. Do not use on an inclined or unstable surface.

15. Keep the appliance and the power cord away from the edge of tables or countertops and out of reach

of children and persons with reduced physical, sensory and mental capacities.

16. Ensure the power cord does not present a tripping hazard.

17. Do not place on or near any heat sources.

18. Follow the instructions when cleaning this appliance.

19. Cleaning or user maintenance shall not be carried out by children without the supervision of a person

responsible for their safety.

20. Do not use this appliance for other than its intended purpose.

21. Misuse of the appliance may cause injury.

22. Do not leave the steamer unattended when switched on or where it may be touched by children or

persons with reduced physical, sensory and mental capacities while it is still hot.

23. This appliance is not a toy. Children should be supervised to ensure they do not play with the

appliance.

24. This appliance is not intended to be operated by means of an external timer or separate remote

control system.

25. For added safety, electrical appliances should be connected to a power outlet that is protected by a

residual current device (RCD / ‘Safety Switch’) having a rated residual operating current not exceeding

30mA. Your switchboard may already incorporate an RCD. If unsure, call an electrician for veriﬁcation

and ﬁtting if necessary.

26. This appliance is intended to be used in household and similar applications such as:

a. Staff kitchen areas in shops, ofﬁces and other working environments;

b. Farm houses;

c. By clients in hotels, motels, and other residential type environments;

d. Bed & breakfast type environments.

SAVE THESE INSTRUCTIONS.

MAX

PARTS

1. Ceramic heating plate

2. Steam trigger lock

3. Steam trigger

4. Handle

5. Water tank

6. Power button

7. Lint attachment

8. Delicate fabric attachment

9. Upholstery attachment

10. Scent infuser attachment

FEATURES

Model Number RHC410

Watts 1800W

Pressing Plate Ceramic coating with infused fabric conditioner

Cord Length 3m

Auto Shut Off After 15 minutes

LED Indicator Flashing when heating

Solid On when Ready

Removable Water Tank Capacity 200mL Max

Heat up Time – 30 secs for steam

– 60 secs to 100C for pressing plate

Steam Rate 30g/min

Attachments – Lint Brush

– Upholstery Bonnet

– Delicate Bonnet

– Scent infuser

PREPARATION

Check for textile care symbols ( ) on items to be steamed.

The steamer comes with three optional-use attachment frames and a scent infuser recommended

for use with a variety of fabrics and upholstery.

1. Select the proper frame using the chart in the ATTACHMENTS section.

2. Remove labels, stickers and packaging from the appliance.

3. Read all instructions and warnings.

IMPORTANT INFORMATION

• For best performance, we recommend using distilled, puried or ltered water in your

steamer. Tap water contains minerals that can build up inside your steamer over time and

reduce its efciency or even cause damage.

• Never use perfumes, oils or other additives for water in the tank.

• Always check the garment’s care label before steaming, and always test fabrics for

colourfastness in an inconspicuous area. Steamers are not recommended for use on leather,

suede, vinyl, plastic, or other materials that are sensitive to steam.

NOTE: During use the steamer and accessories will become HOT. Never try to fit or remove attachments

while still hot.

• After preheating, prime the water pump by holding the steam trigger until steam forms. It is

normal to feel or hear the water pump inside the device. It may become louder when the water

level in the tank is low. Check and rell the tank when required.

NOTE: Small amounts of dripping might occur during use. If excessive, your steamer needs time to get back

up to full temperature. Just allow the steamer a minute to reheat.

• Wearing clothes immediately after ironing or steaming can create wrinkles. Always allow the

clothing to cool for about 5 minutes before wearing.

ATTACHMENTS

Your steamer has three attachments:

Frame Usage

Lint Frame Use on garments labelled kl that allow the use of

steam.

Tip: The pad on the attachment helps remove lint, hair, and

animal fur.

Delicate Frame with scent infuser Use on garments labelled jthat allow the use of steam.

Tip: For items with printing/embellishment, turn the garment

inside out to avoid damage to sensitive areas.

Use the scent infuser to infuse your favourite perfumes

onto your fabrics.

Upholstery Frame Use to sanitise and refresh bedding, mattresses, curtains,

plush toys, furniture, and hard surfaces (such as worktops

or desks that are not heat sensitive).

Tip: Always test for colorfastness and heat sensitivity on an

inconspicuous area.

FITTING / REMOVING ATTACHMENTS'

1. 1. Make sure that the steamer and attachment are

cool.

2. Hook the top of the attachment over the top edge

of the steamer. Click the bottom edge into place.

Make sure it is fully tted and not loose or it may

detach itself during use.

3. Remove the attachment using the tab. When

removing the attachment, watch out for

condensation that may have built up during use.

FILLING

You may use the steamer with tap-water, however if you live in a hard water

area, you should use distilled water (not chemically descaled or softened

water).

If you buy distilled water, check it is marked as suitable for use in

irons / steamer.

•Place the steamer on its base on a stable surface.

•Hold the handle to stabilise and pull out the removable water tank with

the other hand. (Fig. B)

•Gently open the rubber cover at the top of the tank.

•Fill until the water reaches the “MAX” level mark on the side of the tank

(Fig. C). Do not overll. Close the rubber cover securely.

•Fill slowly, to let the air in the tank escape, otherwise you will cause an air

lock and the water may overow.

• Dry off any excess water from the tank. Then ret it into the base until it clicks.

MAX

• To rell at any time during use, turn steamer off by pressing the power button until the blue

indicator light is off, unplug from outlet, and follow the above procedure.

NOTE: After refilling, allow to reheat for 45 seconds and then prime pump by holding steam trigger until

steam forms.

USING

• If the label says “do not iron” or shows this icon i, fit the delicate attachment and make

sure to test on an inconspicuous area prior to steaming the entire garment.

• If the label says “do not steam” or shows this icon , do not steam the garment.

1. Hang the garment in an area that will not be affected or damaged by the heat and steam,

such as on a shower curtain rail, or in an open doorway.

2. Fit any attachment you wish to use.

3. Plug the steamer in then press the power button. The blue power button light will slowly flash,

indicating that the steamer is heating.

4. After about 45 seconds the power light will stay on, indicating the steamer is preheated.

5. Prime the water pump by holding steam trigger until steam forms.

6. To generate steam, press the steam trigger. As long as the trigger is held, steam will emit

from the steamer. When the trigger is released, the steam will stop.

7. To generate a constant flow of steam without holding the trigger, press the steam trigger and

then slide the steam trigger lock downwards. You can then release pressure on the steam

trigger. To turn the steam off, press the trigger, slide the steam trigger lock upwards, then

release the trigger.

8. With your free hand keep the fabric taut. Steam the garment with slow, downward strokes,

keeping the head of the steamer in contact with the fabric.

9. When you have finished, press and hold the power button until the blue light goes out (about

3 seconds) and unplug.

10. Stand the steamer on its base and allow it to completely cool off before storing. To avoid

mineral buildup, empty the tank after each use.

Ceramic heated plate

Your steamer features a ceramic heated plate that helps smooth out wrinkles and creases on the

areas of garments that are more difficult to reach with steam alone. The temperature of the plate

is safe for all ironable fabrics.

To use, hold the plate of the steamer directly against the fabric. Don’t fit any of the attachments.

Steam the garment with slow, downward strokes while keeping the plate in contact with the

fabric.

Using the scent infuser

The scent infuser attachment can be used to infuse your fabrics with your

favourite scent.

• The use of scents, oils, or other fragrances is at your own risk and we

accept no liability. Always read any instructions, warnings or advice

regarding the use of the fragrance before using it with your steamer.

Always use the scent infuser in a well ventilated room.

• Always remove and ret the scent infuser attachment when the steamer

is cold and not producing steam.

• Always have the scent infuser tted when using the delicate fabric attachment. Remove the

fabric pad if you don’t want to infuse a scent to the fabric being steamed.

MAX

1. Remove the scent infuser (Fig. D).

2. Place a few drops of the fragrance onto the fabric pad (Fig. E). Only use

the scent infuser. Do not place fragrance directly onto the delicate fabric

attachment, and never add fragrances to the water in the water tank.

3. Replace the scent infuser into the delicate fabric attachment.

AUTO SHUT-OFF

The Pump & boiler of steamer will automatically be shut off after the power switch or trigger have

been left inactive for 15 minutes (+/-1min). Rapid blinking of the power button light indicates that

the steamer is going into auto shut-off mode. To resume steaming, press the steam trigger or

power button and wait for steamer to fully reheat.

STEAM CLEANING AROUND THE HOME

Using steam to clean household items that can tolerate hot, damp steam without damage is

non-toxic, and inexpensive. This natural cleaning method is beneficial to those sensitive to

chemical cleaners or trying to reduce chemicals in the home. Steam upholstery, draperies, linens

and home textiles to clean and refresh.

CARE AND MAINTENANCE

1. Make sure steamer is off, unplugged and completely cool.

2. Wipe the pressing plate and outer surface with soft, damp cloth. Water and small amounts of

gentle household soaps, such as dishwashing liquid, can be used on the exterior. Never use

heavy-duty cleaner, or abrasive scouring pads that may scratch or discolor the steamer.

3. After the steamer has been thoroughly dried, turn it back on and lightly steam over an old

cloth. This will help remove any reside left in the steam holes.

4. To avoid mineral buildup, empty the tank after each use.

CLEANING ATTACHMENTS

For all accessories, allow to fully dry before using again or storing.

Accessories are not suitable for cleaning in a washing machine.

• Lint attachment: Wipe with damp cloth to clean.

• Delicate fabric attachment: Wash with cold water and small amounts of

gentle cleanser if needed. The fabric in the frame cannot be removed.

• Upholstery attachment: The fabric on this frame can be removed and

hand washed with cold water and gentle cleanser.

• Scent diffusor: Remove the scent diffusor and open it up (Fig. F).

Remove the fabric pad and wash under running water with a little

detergent (Fig. G).

STORING THE STEAMER

1. Check that the steamer is unplugged and completely cool.

2. Gather the cord into even ovals and then gently cinch with the strip of

hook and loop. (Fig. H)

3. Always store steamer upright on its base to prevent water leakage.

Tip: Emptying the tank after each use is recommended because standing

water can leave a residue over time.

MAX

TROUBLESHOOTING

Problem Possible Cause Solution

The steamer is plugged in but not

heating.

The auto shut-off has

activated.

Press the steam trigger or

press the power button to

activate the steamer.

Not enough steam or no steam is

coming out of the steamer.

The steamer is not heated to

full temperature.

Always allow steamer to

preheat at least 45 seconds,

or until the power button light

stops flashing.

There is not enough water in

the water tank.

Fill the water tank.

The water pump hasn’t been

primed.

After preheating, always prime

the water pump by holding

the steam trigger until steam

forms.

Discoloured water is coming

through the holes and staining

the fabric.

Residue has built up in the

water tank.

Empty the water tank after

each use. Only use distilled,

filtered, or purified water.

Perfumed or scented additives

were used.

Never use perfumed or

scented additives.

Steamer is leaking or spitting. Steamer is not hot enough. Allow the steamer to heat for

about 45 seconds.

Water tank is running low. Fill the water tank.

DISPOSAL/RECYCLING

Legislation in some localities mandates that e-waste (anything with a plug, battery or cord)

is disposed of through controlled recycling facilities and must not be disposed of in general

household waste. For more information about recycling of electrical and battery operated

appliances, please contact your local council or your local household waste disposal service.

NOTES

Spectrum Brands Australia Pty Ltd

Locked Bag 3004 Braeside

Victoria 3195 Australia

Customer Service in Australia

TollFree: 1800 623 118

Email: [email protected]

Website: www.spectrumbrands.com.au

Spectrum Brands New Zealand Ltd

PO Box 9817 Newmarket

Auckland 1149 New Zealand

Customer Service in New Zealand

TollFree: 0800 736 776

Email: [email protected]

Website: www.spectrumbrands.co.nz

Spectrum Brands Australia Pty Ltd and Spectrum Brands New Zealand Ltd

Warranty Against Defects

In this warranty:

Australian Consumer Law means the Australian consumer law set out in Schedule 2 to the

Competition and Consumer Act 2010;

CGA means the New Zealand Consumer Guarantees Act 1993;

Goods means the product or equipment which was accompanied by this warranty and

purchased in Australia or New Zealand, as the case may be;

Manufacturer, We or us means:

1. for Goods purchased in Australia, Spectrum Brands Australia Pty Ltd ABN, 78 007 070 573;

2. for Goods purchased in New Zealand, Spectrum Brands New Zealand Ltd, as the case

may be, contact details as set out at the end of this warranty;

Supplier means the authorised distributor or retailer of the Goods that sold you the Goods in

Australia or in New Zealand; and

You means you, the original end-user purchaser of the Goods.

1. Our goods come with guarantees that cannot be excluded under the Australian Consumer

Law, or the CGA. You are entitled to a replacement or refund for a major failure and

compensation for any other reasonably foreseeable loss or damage. You are also entitled

to have the goods repaired or replaced if the goods fail to be of acceptable quality and the

failure does not amount to a major failure.

2. The benefits provided by this Warranty are in addition to all other rights and remedies in

respect of the Goods which the consumer has under either the Australian Consumer Law

or the CGA. The original purchaser of the Goods is provided with the following Warranty

subject to the Warranty Conditions:

3. We warrant the Goods for all parts defective in workmanship or materials from the date

of purchase, for the period of 2 years from the date of purchase (Warranty Period)

If the Goods prove defective within the Warranty Period by reason of improper workmanship

or material, we may, at our own discretion, repair or replace the Goods without charge.

Warranty Conditions

4. The Goods must be used in accordance with the manufacturer’s instructions. This

Warranty does not apply should the defect in or failure of the Goods be attributable

to misuse, abuse, accident or non-observance of manufacturer’s instructions on the

part of the user. As far as the law permits, the manufacturer does not accept liability

for any direct or consequential loss, damage or other expense caused by or arising

out of any failure to use the Goods in accordance with the manufacturer’s instructions.

5. Exhaustible components (such as batteries, ironing board cover, filters and brushes) of

the Goods are included under this Warranty only where there is a defect in

workmanship or materials used.

6. The warranty granted under clause 3 is limited to repair or replacement only.

7. Any parts of the Goods replaced during repairs or any product replaced remain the

property of the manufacturer. In the event of the Goods being replaced during the

Warranty Period, the warranty on the replacement Goods will expire on the same

date as for the Warranty Period on the original Goods which are replaced.

8. In order to claim under the warranty granted under clause 3 you must:

(a) Retain this warranty with your receipt/proof of purchase; and

(b) Return the Goods to us at the relevant address or to the Supplier by prepaid

freight within the Warranty Period accompanied with (i) the legible and unmodified

original proof of purchase, which clearly indicates the name and address of the

Supplier, the date and place of purchase, the product name or other product serial

number and (ii) this warranty.

9. This warranty is immediately void if:

(a) Any serial number or appliance plate is removed or defaced;

(b) The Goods have been serviced or otherwise repaired by a person not authorised

to do so by us or where non approved replaced parts are used.

10. The Goods are designed for domestic use only. A limited 90-day Warranty applies to

any industrial or commercial use of the Goods. The Goods must be connected to the

electrical voltage requirements as specified in the ratings label located on the Goods.

11. This warranty does not cover the cost of claiming under the warranty or transport

of the Goods to and from the Supplier or us.

12. This warranty is only valid and enforceable in Australia against Spectrum Brands

Australia Pty Ltd and in New Zealand against Spectrum Brands New Zealand Ltd.

If you live in Australia please visit: www.spectrumbrands.com.au/warranty

If you live in New Zealand Please visit: www.spectrumbrands.co.nz/warranty

Registration of your warranty is not compulsory, it gives us a record of your purchase

AND entitles you to receive these benefits: Product information; Hints and tips; Recipes

and news; Information on special price offers and promotions.

Any questions? Please contact Customer Service for advice.