Ryobi RWT2CL User manual

22/08/2016
Version 1.0
RWT2CL
579963

Important!
It is essential that you read the instructions in this manual before operating this
machine.
6XEMHFWWRWHFKQLFDOPRGL¿FDWLRQV
SAVE THESE INSTRUCTIONS FOR FUTURE USE

180
■ Do not load with more than 180 kg. Do not leave
heavy loads on work surface for extended
periods of time.
■ Do not apply an unbalanced load which could
cause the workbench to tip over.
■ Do not use the work center as a stepladder or
standing platform. Do not use the lower platform
as a step.
■ Do not store workbench outdoors or in a damp
location.
■ Avoid applying excessive force when clamping
with the supplied clamps.
■ Be sure that the legs are fully open and the
center support is in position and locked before
use.
■ When using a power tool with the workbench,
follow the safety instructions in the tool’s
instruction manual.
■ Do not mount or clamp power tools to any
surface.
■ Always wear safety glasses when operating
power tools.
■ Cutting or drilling into work surface may weaken
supports, damaging tool or workbench.
■ Caution required when using high temperature
tools (heat guns, torch, solder iron, etc.). May
damage work surface and reduce clamping
capability.
■ Do not store flammable liquids on the
workbench.

Upper plate Latches
Side support
Bottom plate
Clamps
Legs
Feet
Carry handle
Side support
Center support

Operation: Opening The Workbench
The Portable Clamping Workstation is packaged completely folded. To open:
1. Place the workbench flat on the floor.
2. Grasp the openings on both sides of the table top and pull out on the release latches as shown in
figure A.
CAUTION: Do not pull the legs out when the workbench is in a closed position. Beware of fingers
when opening, sliding parts may pinch
3. With the release latches pulled in, lift the table top. The four legs will drop down and lock into place
and the side supports will lift up. (figure B)
4. To lock the side supports, push out from the inside until the support locks into position (figure C).
CAUTION: Risk of Unsafe Operation. Make sure all four legs and both side supports are locked in
place.
5. After locking the side supports in place, lift the center support section by the carrying handle until
you hear it “click” into place as shown in figure D.
6. When the center support section is properly locked in position, the LOCK button shown in figure E
will be visible.
CAUTION: Risk of Unsafe Operation. Make sure the center support section is locked in place.
®
A
B
D
E
C

Operation: Closing The Workbench
1. Fold the center support section down and push in on the side supports to unlock them (figure F)
2. Reach through the openings in the table top and grasp the lower section of the bench. Pull up on the
lower section to begin collapsing the legs. (figure G)
3. Lower the unit to the ground as shown in figure H.
4. Once the unit is flat on the ground, press down on the table top to place the unit into its fully closed
position as shown in figure I.
F
G
H
I

Adjustable clamps
The two adjustable clamps can be used in both a vertical and horizontal mode. The long channels in the
table top allow the clamps to be anchored in a stationary horizontal position. The shorter slots in the
table top allow for the clamps to be used in a vertical position (figure J). J1 through J6 illustrate how to
use the clamps in both horizontal and vertical modes.
J1 - To expand the opening of the clamp jaws, press in on the release lever and move the jaw as shown.
The jaw that is attached to the handle can also be moved in the same manner or by squeezing and
releasing the front handle.
J2 - Line up the round post on the end of the clamp bar with the mating openings on both sides of the
main slot in the tabletop as shown.
J3 - To lock the clamp in a horizontal position, squeeze the front handle and line up the round protruding
tabs with the mating openings in the tabletop (behind the openings mentioned in J2 above).
J4 - With the clamp in a fully horizontal position, release the front handle to lock the clamp in place. (To
remove the clamp, squeeze the handle and lift up.)
J5 - Depress the release lever and move the front jaw into position against the material to be clamped.
Squeeze the front handle to apply pressure.
J6 - To clamp vertically, insert the clamp through the slot in the tabletop as shown.
J
J1 J2

Adjustable clamps
Transporting & Maintenance
Carry the unit by the convenient carrying handle
as shown in figure K.
Use only mild soap and damp cloth to clean the
tool. Never let any liquid get inside the tool; never
immerse any part of the tool into a liquid.
1
2
J3
J4
J5
J6
K
85 x 55 x 75.5 cm
12.25 kg
Max Weight
Components
180 kg
1x Folding Table
2x Bar Clamps

Techtronic Industries (Australia) Pty. Ltd.
www.ryobi.com.au
www.ryobi.co.nz
31 Gilby Road, Mount Waverley,
VIC, Australia 3149
Techtronic Industries New Zealand Ltd.
2 Landing Drive, Auckland Airport, Mangere,
New Zealand 2022

Techtronic Industries Australia Pty Ltd ABN 98 002 277 509 and
Techtronic Industries New Zealand Limited provide the following
warranty in relation to any Ryobi product (and any accessory supplied
with it) that has been purchased in Australia or New Zealand (Product)
when the Product is determined by Techtronic Industries Australia Pty
Ltd or Techtronic Industries New Zealand Limited to have a defect in its
material or workmanship.
The period of the warranty will be 24 months commencing from the date
of the sale of the Product by a retailer to the consumer.
1. THIS WARRANTY:
The benefits provided to the consumer in this warranty are in addition to
other rights and remedies of a consumer under the Australian Competition
and Consumer Act 2010, the New Zealand Consumer Guarantees Act
1993 and any other laws in relation to the Products to which this warranty
relates. This warranty:
(a) covers the Product against faulty materials or workmanship; and
(b) covers the replacement of parts, the repair labour used, a refund
of the price of the Product or other compensation for the
remainder of the warranty period.
2. CONSUMER GUARANTEE
For Products sold in Australia, this warranty is subject to the Competition
and Consumer Act 2010. For Products sold in New Zealand, this
warranty is subject to the Consumer Guarantees Act 1993.
The Products come with guarantees that cannot be excluded under the
consumer laws in Australia and New Zealand. The consumer is entitled
to a replacement or refund for a major failure and for compensation for
any other reasonably foreseeable loss or damage. The consumer is
also entitled to have the Products repaired or replaced if the Products
fail to be of acceptable quality and the failure does not amount to a
major failure.
3. THIS WARRANTY WILL NOT APPLY IF:
(a) repairs to the Product are made or attempted by a service
provider other than Techtronic Industries Australia Pty Ltd,
Techtronic Industries New Zealand Limited or an authorised
service centre;
(b) the product is subject to normal wear and tear. Parts including,
but not limited to carbon brushes, bearings, seals and o rings must
be regularly inspected so that the wear and tear on such parts do
not lead to failure of the tool. For optimum performance the tool
should be inspected regularly by an authorised service centre;
(c) the Product has not been used or maintained in accordance with
the manufacturer’s instructions as provided with the Product;
(d) the consumer uses the Product in an abnormal manner for
example if the Product is abused, misused, dropped, crushed,
impacted with any hard surface, exposed to extreme heat
(including fire) or cold, not maintained properly or used after
partial failure;
(e) damage to the Product is caused by sand, water damage, rust
corrosion, fire, vermin and/or insect infestation, power outages
or surges or inadequate or improper voltage or current;
(f) the Product has been modified, incorrectly adjusted or operated,
subjected to incorrect electrical supply or inconsistent electrical
supply or used with inappropriate accessories; or
(g) the Product is tampered with any way or if the damage has been
caused by an extraordinary event or circumstance beyond the
control of the consumer or Techtronic Industries Australia Pty
Ltd or Techtronic Industries New Zealand Limited.
(h) The Product’s serial number, as applied by the manufacturer,
has been altered or removed from the Product.
4. EXCLUSION OF IMPLIED WARRANTIES:
To the full extent permitted by law, all warranties, conditions and other
terms express or implied by statute, custom or common law are
excluded. Nothing contained in these terms and conditions excludes or
restricts any consumer guarantee, warranty, condition, right or remedy
implied by any statute (including the Australian Competition and
Consumer Act 2010 and the New Zealand Consumer Guarantees Act
1993) which cannot be excluded, provided that, to the extent that the
statute permits Techtronic Industries Australia Pty Ltd and Techtronic
Industries New Zealand Limited are entitled to limit its liability as set out
in clause 5 below for a breach of a guarantee, condition or a warranty
implied by that statute.
5. UNDER THIS WARRANTY:
(a) If there is a major failure with the Product, the consumer is
entitled to:
(i) reject the Products and get an identical replacement, or one
similar in value if reasonably available; or
(ii) reject the Products and get a refund;
(iii) keep the Products and obtain compensation from Techtronic
Industries Australia Pty Ltd or Techtronic Industries New
Zealand Limited for the drop in value of the product caused
by the major failure.
(b) If there is a minor failure with the Product, the consumer is
entitled , at the election of Techtronic Industries Australia Pty
Ltd, Techtronic Industries New Zealand Limited, to a refund of
the cost of the Product;
(i) a replacement of the Product; or
(ii) have the Product repaired within a reasonable time; or
(iii) a refund of the cost of the Product
(c) The Products covered by this warranty will be repaired, during
normal business hours at the premises of Techtronic Industries
Australia Pty Ltd, Techtronic Industries New Zealand Limited or
an authorised service centre without cost to the consumer for
parts and repair labour.
(d) The consumer is responsible for freight costs and insurance
costs if the Product has to be returned for repair / inspection to
Techtronic Industries Australia Pty Ltd, Techtronic Industries
New Zealand Limited or the authorised service centre unless the
cost of returning, removing or transporting the Product is
significant.
6. TO CLAIM THIS WARRANTY:
(a) The consumer must present the sales docket receipt and
product to point of sale or Techtronic Industries Australia Pty
Ltd, Techtronic Industries New Zealand Limited or an authorised
service centre.
(b) For Service in Australia the consumer should refer to the Ryobi
web site or contact the Australian Customer Support line on
1300 361 505 to obtain the nearest authorised service centre.
(c) For Service in New Zealand the consumer should contact the
New Zealand Hotline Application on 0800 279 624 to obtain the
nearest authorised service centre.
Techtronic Industries Australia Pty Ltd and Techtronic Industries New
Zealand Limited will honour all warranty claims that are submitted by a
consumer in accordance with these terms and conditions.
TECHTRONIC INDUSTRIES AUSTRALIA PTY LIMITED
WARRANTY TERMS AND CONDITIONS
FOR RYOBI PRODUCTS AND ACCESSORIES
SCHEDULE TO WARRANTY TERMS AND CONDITIONS FOR RYOBI PRODUCTS AND ACCESSORIES
Product type Warranty period Product type Warranty period
Corded power tools 2 (two) years
Engine powered products 2 (two) years
NiCd & NiMH batteries and chargers 2 (two) years
Cordless NiCd & NiMH power tools
excluding batteries and chargers 2 (two) years Lithium-ion batteries and chargers 2 (two) years
Cordless lithium-ion power tools,
excluding batteries and chargers 2 (two) years 3 (three) months
3 (three) months
Power tool accessories and attachments,
including chucks collets, grinder flanges, drill
bits and dust bags.
Consumables; chucks, brushes, O-rings, seals,
bearings.
2 (two) years
Digital Measuring Tools

PRESENT THIS FORM WITH YOUR PURCHASE DOCKET WHEN WARRANTY SERVICE IS REQUIRED.
THIS WARRANTY SHOULD BE RETAINED BY THE CUSTOMER AT ALL TIMES
For your record and to assist in establishing date of purchase (necessary for in-guarantee service)
please keep your purchase docket and this form completed with the following particulars:
Purchased from Address of dealer Purchase date Model number Serial number
All Australian enquiries: 1300 361 505 (toll free)
TECHTRONIC INDUSTRIES AUSTRALIA PTY LIMITED
A.B.N. 98 002 277 509
31 Gilby Road, Mt Waverley, VIC 3149, Australia
Fax: [phone]
Contact during normal business hours.
www.ryobi.com.au
TECHTRONIC INDUSTRIES N.Z. LIMITED
2 Landing Drive, Mangere,
Auckland, New Zealand 2022
Tel: [phone] Fax: [phone]
Contact during normal business hours.
www.ryobi.co.nz
All New Zealand enquiries: 0800 279 624 (toll free)
TECHTRONIC INDUSTRIES AUSTRALIA PTY LIMITED
WARRANTY REGISTRATION FORM
961067836-05