Safe Fleet Prime Design CSM-1001 Series User manual

CSM-1001
Page 2 Packaging Contents
Page 3–4 Requirements
Pages 4–5 Assembly Instructions
Cantilever Shelving Mounting Assembly– Ford Transit High Roof
PRIME DESIGN, A SAFE FLEET BRAND ▪ Address: 1689 Oakdale Avenue #102, West St Paul, Minnesota 55118
Toll Free: 1.8.PRIME.RACK ▪ Fax: [phone] ▪ Email: [email protected] ▪ Website: www.primedesign.net

Prime Design Limited Warranty. Seller’s sole and exclusive warranty (and Buyer’s sole and exclusive remedy and Seller’s entire liability for any breach thereof) with respect to the Goods is set forth in the Limited Warranty document available at primedesign.net/warranty-liability
(the “Prime Design Limited Warranty”).
▪
TM & © 2021 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6427889, 6764268, 6971563, 8991889, 9415726, 9506292, 9481313, 9776476, 9796340, 10470565, 10486608, 10501022 AND OTHER PATENTS PENDING
2
CSM-1001 SERIES ASSEMBLY INSTRUCTIONS–PACKAGING CONTENTS
CONTENTS OVERVIEW
2—HKT-0203 ........................................................ (Qty 1)
3—Hardware supplied in Cantilever Shelving Upright
Packaging (CSU-3001 or CSU-3002)-sold separately.
* Used in Step 4
1—Cantilever Shelving Mounting System ............ (Qty 1)
Ford Transit, High Roof
M8 x 18MM (6X) M8 x 25MM (12X)
M8 x 25MM (1X)
Caddy Mounting
Spacer (6X)
Nut Rivet (6X)
Interior Mounting Assembly (6X) 51.00” Mounting Channel Assembly (1X)
32.00” Mounting Channel Assembly (1X)24.00” Mounting Channel Assembly (1X)
Lock Washer (18X)
Lock Washer (1X)
Flat Washer (18X)
Flat Washer (1X)

Prime Design Limited Warranty. Seller’s sole and exclusive warranty (and Buyer’s sole and exclusive remedy and Seller’s entire liability for any breach thereof) with respect to the Goods is set forth in the Limited Warranty document available at primedesign.net/warranty-liability
(the “Prime Design Limited Warranty”).
▪
TM & © 2021 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6427889, 6764268, 6971563, 8991889, 9415726, 9506292, 9481313, 9776476, 9796340, 10470565, 10486608, 10501022 AND OTHER PATENTS PENDING
3
CSM-1001 SERIES ASSEMBLY INSTRUCTIONS–REQUIREMENTS
ASSEMBLY REQUIREMENTS
• These instructions are subject to change if the manufacturer revises
the parts and/or production of the subsystems and accessories used in
the brand’s vehicles. Following the instructions for assembly will ensure
proper installation of the product. The manufacturer will not be held
liable if these instructions are not followed.
• The addition of parts and/or components not original to this Cantilever
Shelving are discouraged. Use only OEM supplied parts.
• Consultaion of the OEM vehicle may be required during assembly to
avoid vehicle damage. Ensure bolt locations will not damage any
critical parts of the vehicle–i.e. gas tank, wiring harnesses, or
hoses-before drilling.
INSTALLER NOTE: It is important to correctly follow
these assembly instructions. These instructions for
assembly are provided by the manufacturer at time of
Cantilever Shelving delivery, and reect the technical
specications applicable at the time of writing.
Torque Wrench w/
13MM Socket
Plus Nut Applicator Tool
REQUIRED

Prime Design Limited Warranty. Seller’s sole and exclusive warranty (and Buyer’s sole and exclusive remedy and Seller’s entire liability for any breach thereof) with respect to the Goods is set forth in the Limited Warranty document available at primedesign.net/warranty-liability
(the “Prime Design Limited Warranty”).
▪
TM & © 2021 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6427889, 6764268, 6971563, 8991889, 9415726, 9506292, 9481313, 9776476, 9796340, 10470565, 10486608, 10501022 AND OTHER PATENTS PENDING
4
CSM-1001 SERIES ASSEMBLY INSTRUCTIONS
Align
ASSEMBLY OVERVIEW
CSM ASSEMBLY SEQUENCE
Locate the factory tie in hole locations on the
Service Body and align with an Interior Mounting
Assembly as shown.Hold into position for drilling
location in Step 1.2
NOTE: Mounting Assembly shown installed with Uprights
for illustrative purpose only. Separate purchase is
required for Uprights and Shelves.
Install a Nut Rivet
into the drilled hole
Drill into the
location shown.
1.1
1.2
1.3

Prime Design Limited Warranty. Seller’s sole and exclusive warranty (and Buyer’s sole and exclusive remedy and Seller’s entire liability for any breach thereof) with respect to the Goods is set forth in the Limited Warranty document available at primedesign.net/warranty-liability
(the “Prime Design Limited Warranty”).
▪
TM & © 2021 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6427889, 6764268, 6971563, 8991889, 9415726, 9506292, 9481313, 9776476, 9796340, 10470565, 10486608, 10501022 AND OTHER PATENTS PENDING
5
Incorrect Channel Orientation
Flat Washer
Lock Washer
M8 x 18MM Bolt
Corrrect Channel Orientation
Flat Washer
Lock Washer
M8 x 25MM Bolt
Flat Washer
Caddy Mounting Spacer
Lock Washer
M8 x 25MM Bolt
Attach the Interior Mounting Assembly with Hardware as
shown into the factory tie in hole. Torque to 90 in-lbs.
Install the Mounting Channel in its correct orientation
using Hardware as shown. Torque to 90 in-lbs.
2.1
3.1
Install Hardware into the lower Mounting Assembly hole
as shown. Torque to 90 in-lbs.
Repeat Steps 1.1–3.1 on all parts
and hardware as needed for your
specic conguration.
2.2
3.2
Lock Washer
M8 x 25MM
Flat Washer
Uprights (sold separately) are installed into CSM-1001
according to your specic conguration. Torque hardware
to 90 in-lbs.
4
*Hardware used in Step 4 is from HKT-0204
contained in Upright packaging CSU-3001 or
CSU-3002 (sold separately).
NOTE: View below is shown with shelving removed
for visual clarity.
CSM-1001 SERIES ASSEMBLY INSTRUCTIONS

Page Intentionally Left Blank

Page Intentionally Left Blank

USAM-CSM-US01 Rev-B 0621