Safe Fleet PRIME DESIGN VBC-TC11B User manual

PRIME DESIGN, A SAFE FLEET BRAND ▪Address: 1689 Oakdale Avenue #102, West St Paul, Minnesota 55118 ▪Phone: [phone] ▪Toll Free: 1.8.PRIME.RACK ▪Fax: [phone] ▪Email: i[email protected] ▪Website: www.primedesign.net
TM & © 2018 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6764268, 6971563, 2364879, 8857689, 8511525, 8991889, 2271515, 2364897, 9506292, 9481313, 9481314, 9796340, 6202807, 6427889, 9415726 AND OTHER PATENTS PENDING
2
2
3
4
6
7
8
1
5
9
10
11
Channels (2X)
M6 Locknut (8X) End Caps (4X) Brackets (4X) M6 x 30MM Bolt (8X)
M6 Sealing Washer (8X) Foam Pad (8X)
Mounting Plate (8X)
” Washer (8X)” Flat Washer (8X)
VBC-TC11B ASSEMBLY INSTRUCTIONS–PACKAGING CONTENTS
CONTENTS OVERVIEW
1—FBM-0006 ........................................................ (Qty 1)
Channels with hardware
2—Rear Crossbar Assembly.................................. (Qty 1)
3—Front Crossbar Assembly................................. (Qty 1)
4—Handle Latch Assembly ................................... (Qty 1)

PRIME DESIGN, A SAFE FLEET BRAND ▪Address: 1689 Oakdale Avenue #102, West St Paul, Minnesota 55118 ▪Phone: [phone] ▪Toll Free: 1.8.PRIME.RACK ▪Fax: [phone] ▪Email: in[email protected] ▪Website: www.primedesign.net
TM & © 2018 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6764268, 6971563, 2364879, 8857689, 8511525, 8991889, 2271515, 2364897, 9506292, 9481313, 9481314, 9796340, 6202807, 6427889, 9415726 AND OTHER PATENTS PENDING
3
VBC-TC11B ASSEMBLY INSTRUCTIONS–PACKAGING CONTENTS
7—Quick Clamp Tube Splice Assembly ................ (Qty 1)
5.00“
9—Front Hook Assembly ....................................... (Qty 1)
6—Clamp Down Tube ............................................ (Qty 1)
68.00”
8—Removeable Horn with Cap ............................. (Qty 1)
15.00”
Anti-Seize (1X)
12—Anti-Seize........................................................ (Qty 1)
5—Clamp Down Handle Assembly ....................... (Qty 1)
10—Ladder Stop Assembly................................... (Qty 2)
1.75”
M8 Lock Nut (1X) Flat Washer (2X)
M8 x 45MM (1X)
11—USQSG-Ergorack ............................................ (Qty 1)
Quick Start Guide, Clamp Down

PRIME DESIGN, A SAFE FLEET BRAND ▪Address: 1689 Oakdale Avenue #102, West St Paul, Minnesota 55118 ▪Phone: [phone] ▪Toll Free: 1.8.PRIME.RACK ▪Fax: [phone] ▪Email: in[email protected] ▪Website: www.primedesign.net
TM & © 2018 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6764268, 6971563, 2364879, 8857689, 8511525, 8991889, 2271515, 2364897, 9506292, 9481313, 9481314, 9796340, 6202807, 6427889, 9415726 AND OTHER PATENTS PENDING
4
VBC-TC11B ASSEMBLY INSTRUCTIONS–FBM MOUNTINGS
5.00”
Channel Front
6.25”
Channel Rear
Bracket Nut
Fig. 1
Rear
Front
Left
Right
Front Mounting Brackets
2
2
5
4
3
1
6
7
8
RIGHT CLAMP DOWN
ASSEMBLY SEQUENCE
FBM-0006
CHANNELS TO ROOF 1.2
Front Mounting Brackets only: remove and save
the hardware from the rear Bracket Nut as shown.
1.1
Slide the Bracket Nuts into the Channels as shown.

PRIME DESIGN, A SAFE FLEET BRAND ▪Address: 1689 Oakdale Avenue #102, West St Paul, Minnesota 55118 ▪Phone: [phone] ▪Toll Free: 1.8.PRIME.RACK ▪Fax: [phone] ▪Email: in[email protected] ▪Website: www.primedesign.net
TM & © 2018 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6764268, 6971563, 2364879, 8857689, 8511525, 8991889, 2271515, 2364897, 9506292, 9481313, 9481314, 9796340, 6202807, 6427889, 9415726 AND OTHER PATENTS PENDING
5
Rear
Front
Left
Right
VBC-TC11B ASSEMBLY INSTRUCTIONS–RIGHT SIDE CLAMP DOWN
1.6 Reinstall the Mounting Bracket Nut hardware as shown,
but do not tighten.
Install the front Mounting Brackets as shown and slide
into position over the Bracket Nut.
1.5
Loosen bolts
1.4
1.3
Foam pad
Mounting Plate
Install three sets of Channel Hardware per channel
as shown below.
Install the fasteners through the innermost factory roof
holes as shown then torque the nuts to 60 in-lbs.
Do not install or fasten Hardware to the outer front
and rear roof holes until Step 1.9.

PRIME DESIGN, A SAFE FLEET BRAND ▪Address: 1689 Oakdale Avenue #102, West St Paul, Minnesota 55118 ▪Phone: [phone] ▪Toll Free: 1.8.PRIME.RACK ▪Fax: [phone] ▪Email: in[email protected] ▪Website: www.primedesign.net
TM & © 2018 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6764268, 6971563, 2364879, 8857689, 8511525, 8991889, 2271515, 2364897, 9506292, 9481313, 9481314, 9796340, 6202807, 6427889, 9415726 AND OTHER PATENTS PENDING
6
60.00”7.00”
Channel Rear Channel Front
Rear
Front
Left
Right
VBC-TC11B ASSEMBLY INSTRUCTIONS–RIGHT SIDE CLAMP DOWN
1.9
1.8
Set to distances then torque all the Mounting Brackets
to 90 in-lbs.
Install the remaining rear fasteners through the
factory roof holes then torque the nuts to 60 in-lbs.
1.7 Install the rear Mounting Brackets along with the
remaining Channel Hardware as shown below.
Do not tighten the Mounting Brackets until Step 1.9.
Loosen bolts

PRIME DESIGN, A SAFE FLEET BRAND ▪Address: 1689 Oakdale Avenue #102, West St Paul, Minnesota 55118 ▪Phone: [phone] ▪Toll Free: 1.8.PRIME.RACK ▪Fax: [phone] ▪Email: in[email protected] ▪Website: www.primedesign.net
TM & © 2018 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6764268, 6971563, 2364879, 8857689, 8511525, 8991889, 2271515, 2364897, 9506292, 9481313, 9481314, 9796340, 6202807, 6427889, 9415726 AND OTHER PATENTS PENDING
7
Rear
Front
Even EvenRear
Even EvenFront
VBC-TC11B ASSEMBLY INSTRUCTIONS–LADDER STOPS
CLAMP DOWN HANDLE CLAMP DOWN TUBE
3
4.2
4.1
4.3
4.4
Torque to 90 in-lbs
Torque to 90 in-lbs
CROSSBARS CROSSBAR ADJUSTMENT
2.1
Torque to
90 in-lbs 2.2

PRIME DESIGN, A SAFE FLEET BRAND ▪Address: 1689 Oakdale Avenue #102, West St Paul, Minnesota 55118 ▪Phone: [phone] ▪Toll Free: 1.8.PRIME.RACK ▪Fax: [phone] ▪Email: in[email protected] ▪Website: www.primedesign.net
TM & © 2018 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6764268, 6971563, 2364879, 8857689, 8511525, 8991889, 2271515, 2364897, 9506292, 9481313, 9481314, 9796340, 6202807, 6427889, 9415726 AND OTHER PATENTS PENDING
8
USAM-VBCTC11B-US01 Rev-C 0718
8Place the Quick Start Guide into
the vehicle’s glove box for ladder
setup and adjustment.
QUICK START GUIDE
LADDER STOPS
7.2
Torque to 90 in-lbs
7.1
Loosen nuts
HANDLE LATCH FRONT LADDER HOOK
SEE QUICK START GUIDE FOR ADJUSTMENTS
5.2 Torque to 90 in-lbs
5.1
6.2 Torque to 90 in-lbs
6.1