Safe Fleet Prime Design FBM-1063 User manual

Pages 2-4 Packaging Contents
Pages 5–8 FBM Mounting
Page 9 Mounting to OTC Channels
Pages 9–11 Installing Mount Braces
OTC Mounting System–Low-Prole Height Service Body, Flip Top Lid Model
PRIME DESIGN, A SAFE FLEET BRAND
Address: 580 Opperman Drive, Eagan, MN 55123 ▪ Toll Free: 1.8.PRIME.RACK
Fax: [phone] ▪ Email: inf[email protected] ▪ Website: www.primedesign.net

Prime Design Limited Warranty. Seller’s sole and exclusive warranty (and Buyer’s sole and exclusive remedy and Seller’s entire liability for any breach thereof) with respect to the Goods is set forth in the Limited Warranty document available at primedesign.net/warranty-liability
(the “Prime Design Limited Warranty”).
▪
TM & © 2021 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6427889, 6764268, 6971563, 8991889, 9415726, 9506292, 9481313, 9776476, 9796340, 10470565, 10486608, 10501022 AND OTHER PATENTS PENDING
2
FBM-1063 ASSEMBLY INSTRUCTIONS–PACKAGING CONTENTS
CONTENTS OVERVIEW
Front Base Mounting Leg...................................... (Qty 2)
Rear Base Mounting Leg ...................................... (Qty 2)
Crossbar Mounting Brace..................................... (Qty 2)
Channel Mounting Brace...................................... (Qty 4)
Mounting Leg Connector Assembly ..................... (Qty 4)
Rear Mounting Leg Bracket.................................. (Qty 2)

Prime Design Limited Warranty. Seller’s sole and exclusive warranty (and Buyer’s sole and exclusive remedy and Seller’s entire liability for any breach thereof) with respect to the Goods is set forth in the Limited Warranty document available at primedesign.net/warranty-liability
(the “Prime Design Limited Warranty”).
▪
TM & © 2021 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6427889, 6764268, 6971563, 8991889, 9415726, 9506292, 9481313, 9776476, 9796340, 10470565, 10486608, 10501022 AND OTHER PATENTS PENDING
3
FBM-1063 ASSEMBLY INSTRUCTIONS–PACKAGING CONTENTS
Anti-Seize
Lock Washer (6X)
Crossbar Mounting Connector (4X)
M8 x 45MM (2X)
M8 x 30MM (8X)M8 x 20MM (2X)
M8 x 60MM Carriage Bolt (2X)
M8 x 55MM (6X)
M8 Lock Nut (10X) " Flat Washer (16X)
Fender Washer
(8X)
Rubber Washer
(8X)
M8 Nut Bracket (6X)
HKT-8065 Front Mount Hardware Kit

Prime Design Limited Warranty. Seller’s sole and exclusive warranty (and Buyer’s sole and exclusive remedy and Seller’s entire liability for any breach thereof) with respect to the Goods is set forth in the Limited Warranty document available at primedesign.net/warranty-liability
(the “Prime Design Limited Warranty”).
▪
TM & © 2021 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6427889, 6764268, 6971563, 8991889, 9415726, 9506292, 9481313, 9776476, 9796340, 10470565, 10486608, 10501022 AND OTHER PATENTS PENDING
4
FBM-1063 ASSEMBLY INSTRUCTIONS–PACKAGING CONTENTS
Anti-Seize
Lock Washer (4X)
M8 x 45MM (2X)M8 x 30MM (10X) M8 x 55MM (2X)
M8 x 70MM (4X)
M8 Lock Nut (14X) " Flat Washer (22X)
Fender Washer
(10X)
Rubber Washer
(10X)
M8 Nut Bracket (4X)
HKT-8064 Rear Mount Hardware Kit

Prime Design Limited Warranty. Seller’s sole and exclusive warranty (and Buyer’s sole and exclusive remedy and Seller’s entire liability for any breach thereof) with respect to the Goods is set forth in the Limited Warranty document available at primedesign.net/warranty-liability
(the “Prime Design Limited Warranty”).
▪
TM & © 2021 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6427889, 6764268, 6971563, 8991889, 9415726, 9506292, 9481313, 9776476, 9796340, 10470565, 10486608, 10501022 AND OTHER PATENTS PENDING
5
FBM-1063 ASSEMBLY INSTRUCTIONS–FBM MOUNTINGS
OVERVIEW: MOUNTING TO OTC CHANNELS
NOTE: Channels and Crossbars in this Overview are shown
for reference only. Specic congurations are determined
by Service Body size, and Crossbar preferences.
2.11Install Mounting Leg Connectors onto the Base Mounting
Legs as shown.
Install Rear Mounting Leg Brackets onto the Rear Mounting
Legs as shown and torque to 90 in-lbs.
Remove and
retain Hardware
LEG CONNECTORSREAR MOUNTING LEG BRACKETS
Align outer Connector hole with
the bolt hole on the Mounting Leg
for Hardware re-installation.
M8 x 70MM
Flat Washer
Flat Washer
Locknut

Prime Design Limited Warranty. Seller’s sole and exclusive warranty (and Buyer’s sole and exclusive remedy and Seller’s entire liability for any breach thereof) with respect to the Goods is set forth in the Limited Warranty document available at primedesign.net/warranty-liability
(the “Prime Design Limited Warranty”).
▪
TM & © 2021 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6427889, 6764268, 6971563, 8991889, 9415726, 9506292, 9481313, 9776476, 9796340, 10470565, 10486608, 10501022 AND OTHER PATENTS PENDING
6
FBM-1063 ASSEMBLY INSTRUCTIONS–FBM MOUNTINGS
2.2 Re-install Mounting Leg Connector Hardware as shown. FRONT MOUNTING LEG PLACEMENT
FRONT MOUNTING LEG
DRILLING & BOLT SIZING
Right and Left
Front Legs Aligned
3.1
Install Front Mounting
Legs onto the front inside
corner of your service body
as shown.
NOTE: Depending on the application,
isolation tape (not included) may be
required to prevent the chance of
bimetallic corrosion.
NOTE: Parts of the utility body are
cutaway for illustrative purposes
M8 x 30MM and M8 x 55MM available the
thickness of your utility body. Drill and attach
hardware as needed according to your utility
body’s OEM specications.
Front Passenger Side

Prime Design Limited Warranty. Seller’s sole and exclusive warranty (and Buyer’s sole and exclusive remedy and Seller’s entire liability for any breach thereof) with respect to the Goods is set forth in the Limited Warranty document available at primedesign.net/warranty-liability
(the “Prime Design Limited Warranty”).
▪
TM & © 2021 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6427889, 6764268, 6971563, 8991889, 9415726, 9506292, 9481313, 9776476, 9796340, 10470565, 10486608, 10501022 AND OTHER PATENTS PENDING
7
Flat Washer
Locknut
Rubber Washer
Fender Washer
Flat Washer
Locknut
Rubber Washer
Fender Washer
FBM-1063 ASSEMBLY INSTRUCTIONS–FBM MOUNTINGS
FASTENING FRONT MOUNTING LEGS
M8 x 30MM
(Lower)
M8 x 30MM
(Lower)
M8 x 55MM
(Upper)
M8 x 30MM
(Upper)
3.2 Install Hardware with the appropriate bolt size needed
for your service body. Torque to 90 in-lbs.
NOTE: Parts of the utility body are
cutaway for illustrative purposes
Example shown with uitlity body requiring the
M8 x 55MM bolts in the upper drilling locations.
Front Passenger Side

Prime Design Limited Warranty. Seller’s sole and exclusive warranty (and Buyer’s sole and exclusive remedy and Seller’s entire liability for any breach thereof) with respect to the Goods is set forth in the Limited Warranty document available at primedesign.net/warranty-liability
(the “Prime Design Limited Warranty”).
▪
TM & © 2021 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6427889, 6764268, 6971563, 8991889, 9415726, 9506292, 9481313, 9776476, 9796340, 10470565, 10486608, 10501022 AND OTHER PATENTS PENDING
8
FBM-1063 ASSEMBLY INSTRUCTIONS–FBM MOUNTINGS
REAR MOUNTING LEGS
M8 x 30MM
Align Front and
Back Legs
Flat Washer
Aligned with
Front Leg
Must clear Rear
Light and features
Locknut
Rubber Washer
Fender Washer
Avoid Rear Light
4.1
4.2
4.3 4.4
Install Rear Mounting Legs onto the outside rear of your
service body as shown.
Ensure alignment and light clearance
as shown below.
NOTE: Depending on the application,
isolation tape (not included) may be
required to prevent the chance of
bimetallic corrosion.
NOTE: Refer to OEM recommendations for the instllation of a
support or backing plate behind the mounts.
Install Hardware as shown and torque
to 90 in-lbs.

Prime Design Limited Warranty. Seller’s sole and exclusive warranty (and Buyer’s sole and exclusive remedy and Seller’s entire liability for any breach thereof) with respect to the Goods is set forth in the Limited Warranty document available at primedesign.net/warranty-liability
(the “Prime Design Limited Warranty”).
▪
TM & © 2021 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6427889, 6764268, 6971563, 8991889, 9415726, 9506292, 9481313, 9776476, 9796340, 10470565, 10486608, 10501022 AND OTHER PATENTS PENDING
9
FBM-1063 ASSEMBLY INSTRUCTIONS-MOUNTING TO OTC CHANNELS
MOUNTING TO CHANNELS
Torque all Mounting Bracket
bolts to 90 in-lbs
Crossbars must be installed directly
over the the rear and front mounts.
5.1 Loosen all indicated Nuts to
install the Channels. Do not
tighten until Step 5.3. 5.3
5.2
REAR MOUNTING FOOT
NUT BRACKETS
FRONT MOUNTING FOOT
NUT BRACKETS
6.1 Install one M8 Nut Bracket in each rear
Mounting Foot channel as shown. 6.2 Install one M8 Nut Bracket in each front
Mounting Foot channel as shown.

Prime Design Limited Warranty. Seller’s sole and exclusive warranty (and Buyer’s sole and exclusive remedy and Seller’s entire liability for any breach thereof) with respect to the Goods is set forth in the Limited Warranty document available at primedesign.net/warranty-liability
(the “Prime Design Limited Warranty”).
▪
TM & © 2021 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6427889, 6764268, 6971563, 8991889, 9415726, 9506292, 9481313, 9776476, 9796340, 10470565, 10486608, 10501022 AND OTHER PATENTS PENDING
10
FBM-1063 ASSEMBLY INSTRUCTIONS-INSTALLING MOUNT BRACES
MOUNTING LEG–CHANNEL
BRACE INSTALLATION
Keep Nut Bracket
loose for installation
into inner Channel sides
M8 x 45MM
Lock Washer
Flat Washer
M8 x 55MM
Lock Washer
Flat Washer
7.3 Install the lower end of
the Braces into the Mounting
Foot channels using the
Nut Brackets installed
in Steps 6.1–6.2,
and Hardware
as shown. Torque to
90 in-lbs.
7.1
*Holes must align
7.2 Install Braces into the inside of the Channels as shown.
ADDITIONAL FRONT MOUNTING
FOOT NUT BRACKETS
8Install a second M8 Nut Brackets in each
front Mounting Foot channel as shown.