Safe Fleet Prime Design VBB CE User manual

PRIME DESIGN, A SAFE FLEET BRAND 1689 Oakdale Avenue #102, West St Paul, Minnesota 55118 ▪ Phone: [phone] ▪ 1.8.PRIME.RACK ▪ Fax: [phone] ▪ Email:[email protected] ▪ www.primedesign.net
TM & © 2015 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6092974, 6764268, 6971563, 2364879, 8857689, 8511525, 8991889 AND OTHER PATENTS PENDING
2
2
1
3
End Caps (4X)
Foam Gasket (6X)Nylon Washer (6X)
M8 Bolt (6X)
Channels (2X)
Flex Channel Connector (6X)Brackets (4X)
VBB-CE ASSEMBLY INSTRUCTIONS–PACKAGING CONTENTS
1—FBM-0045 ........................................................ (Qty 1)
Channels with hardware
CONTENTS OVERVIEW
2—Crossbar Assembly........................................... (Qty 2)
3—Ladder Stop Assembly ..................................... (Qty 4)
1.75”

PRIME DESIGN, A SAFE FLEET BRAND 1689 Oakdale Avenue #102, West St Paul, Minnesota 55118 ▪ Phone: [phone] ▪ 1.8.PRIME.RACK ▪ Fax: [phone] ▪ Email:[email protected] ▪ www.primedesign.net
TM & © 2015 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6092974, 6764268, 6971563, 2364879, 8857689, 8511525, 8991889 AND OTHER PATENTS PENDING
3
Rear
Front
Left
Right
Rear
Front
Left
Right
Rear
Front
Left
Right
12.50”
Channel Front
3.25”
Channel Rear
Fig. 1
Nylon Spacer
Foam Gasket
Right Rear
72.00”
6–3/8”
Left Rear
72.00”
6–3/8”
VBB-CE ASSEMBLY INSTRUCTIONS–FBM MOUNTINGS
FBM-0045
CHANNELS TO ROOF
Slide Channel Connectors
into Channels as shown
0.6 Loosen bolts
0.7 Set to distances then torque Rear Bracket nuts to 90 in-lbs
Install Channels into roof Channel groove as shown
0.3
Position Channels as
shown below in Fig.1
0.1
0.2
0.4 Install fasteners into factory
roof rail mounting locations.
0.5
Torque to 150 in-lbs

PRIME DESIGN, A SAFE FLEET BRAND 1689 Oakdale Avenue #102, West St Paul, Minnesota 55118 ▪ Phone: [phone] ▪ 1.8.PRIME.RACK ▪ Fax: [phone] ▪ Email:[email protected] ▪ www.primedesign.net
TM & © 2015 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6092974, 6764268, 6971563, 2364879, 8857689, 8511525, 8991889 AND OTHER PATENTS PENDING
4
1
Rear
Front
2
Even EvenFront
Even EvenRear
BASE ASSEMBLY
CROSSBARS CROSSBAR ADJUSTMENT
1.1
Torque to
90 in-lbs
1.2
VBB-CE ASSEMBLY INSTRUCTIONS–BASE ASSEMBLY

PRIME DESIGN, A SAFE FLEET BRAND 1689 Oakdale Avenue #102, West St Paul, Minnesota 55118 ▪ Phone: [phone] ▪ 1.8.PRIME.RACK ▪ Fax: [phone] ▪ Email:[email protected] ▪ www.primedesign.net
TM & © 2015 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6092974, 6764268, 6971563, 2364879, 8857689, 8511525, 8991889 AND OTHER PATENTS PENDING
5
LADDER STOPS
VBB-CE ASSEMBLY INSTRUCTIONS–LADDER STOPS
ADDITIONAL INFORMATION
For additional information regarding your VBB-CE Ladder Rack, please
visit the Prime Design website at: www.primedesign.net.
Using a QR code reader in your smart phone or tablet, read the QR
Code shown below and follow the same steps as you would from your
laptop or computer.
If you’re viewing this document as an interactive PDF, you may simply
click on the QR Code below to access the Prime Design website.
2.2
Torque to 90 in-lbs
2.1
Loosen nuts