Safe Fleet Prime Design OCM-3032 User manual

OCM-3032
OVER THE CAB ADD-ON CROSSBAR

PRIME DESIGN, A SAFE FLEET BRAND ▪Address: 1689 Oakdale Avenue #102, West St Paul, Minnesota 55118 ▪Toll Free: 1.8.PRIME.RACK ▪Fax: [phone] ▪Email: [e-mail] ▪Website: www.primedesign.net
TM & © 2020 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6427889, 6764268, 6971563, 8991889, 9415726, 9506292, 9481313, 9776476, 9796340, 10470565, 10486608 AND OTHER PATENTS PENDING
2
OCM-3032 ASSEMBLY INSTRUCTIONS–PACKAGING CONTENTS
Pickup Crossbar .................................................... (Qty 1)
67.00”, with Caps and Hardware
CONTENTS OVERVIEW
Lock Washer (4X) Mounting Connector (4X)
Anti-Seize
M8 x 50MM (4X) M8 x 60MM Carriage Bolt (2X)
End Stop (2X)LH Removable
Crossbar Mount (1X)
RH Removable
Crossbar Mount (1X)
M8 Lock Nut (2X) " Flat Washer (6X)
M8 Nut Bracket (4X)
HKT-0183 Removable Crossbar Hardware Kit

PRIME DESIGN, A SAFE FLEET BRAND ▪Address: 1689 Oakdale Avenue #102, West St Paul, Minnesota 55118 ▪Toll Free: 1.8.PRIME.RACK ▪Fax: [phone] ▪Email: [e-mail] ▪Website: www.primedesign.net
TM & © 2020 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6427889, 6764268, 6971563, 8991889, 9415726, 9506292, 9481313, 9776476, 9796340, 10470565, 10486608 AND OTHER PATENTS PENDING
3
Left side shown-repeat on right
OCM-3032 ASSEMBLY INSTRUCTIONS–ASSEMBLY INSTRUCTIONS
M8 x 60MM Carriage Bolt
Locknut
Flat Washer
M8 x 50MM
Lock Washer
Flat Washer
Leave M8 Nut Brackets
loose until Step 5
Leave M8 Nut Brackets
loose until Step 5
Slide rear Removable
Crossbar forward
ASSEMBLY INSTRUCTIONS
NOTE: Channels in this Overview are shown for
reference only. Specic channels and congurations
are determined by Service Body size.
CROSSBAR MOUNT BUILDS PRE-INSTALLED
REMOVABLE CROSSBAR
1.1
1.2
2.1
Loosen bolts
2.2

PRIME DESIGN, A SAFE FLEET BRAND ▪Address: 1689 Oakdale Avenue #102, West St Paul, Minnesota 55118 ▪Toll Free: 1.8.PRIME.RACK ▪Fax: [phone] ▪Email: [e-mail] ▪Website: www.primedesign.net
TM & © 2020 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6427889, 6764268, 6971563, 8991889, 9415726, 9506292, 9481313, 9776476, 9796340, 10470565, 10486608 AND OTHER PATENTS PENDING
4
USAM-OCM3032-US01 Rev-A 0220
Variable Placement
Flush to end
OCM-3032 ASSEMBLY INSTRUCTIONS–ASSEMBLY INSTRUCTIONS
ADD-ON CROSSBAR INSTALLATION
3Install Mounts into Channels
as shown below.
4.1
Set Crossbars into the Mounts
as shown and torque Crossbar
Connector Hardware to 90 in-lbs.
Attach Ladder stops as shown
and torque to 90 in-lbs.
4.2
5Set to distances as shown below, and torque all Removable Crossbar Mounts into the Channels at 90 in-lbs.
NOTE: Channels and FBM are shown for reference. Specic channels and congurations are determined by
Service Body size.