Salda VSA 3.0 Series Guide

VSA 3.0/VSA EKO
EN MOUNTING AND INSTALLATION INSTRUCTION

2 | EN VSA 3.0_VSA EKO v2019.04
SYMBOLS AND MARKING
Product name
Nominal voltage frequency
Max.current
Max.power consumption
Protection class
/ 000 0VAC
00.00 A
0.00 kW
IP 00
/0 /Hz
Made in Šiauliai, Lithuania
SKU000000
LN: LN000000 2019.01.01
1
4
5
2
6
3
Figure 1.1 - Technical label
1 - Logo; 2 - Product code (SKU); 3 - Product name; 4 - Technical data; 5 - Production place; 6 - Lot number and production date.
Techninis
lipdukas
XXXGAMINIO PA VADINIMAS
Nominalvoltagefrequency
Max.current
Max.powerconsumption
Protectionclass
Weight
/xxx/xxVAC/Hz
x.xxA
x.xxkW
IPxx
xxkg
Madein Šiauliai,Lithuani a
FAN000040
BN:xxxxxx
2019/01/01
Techninis
lipdukas
Product name
Nominal voltage frequency
Max.current
Max.power consumption
Protection class
/000 0VAC
00.00A
0.00 kW
IP 00
/0 /Hz
Made in Šiauliai, Lithuania
SKU000000
LN: LN000000 2019.01.01
Product name
Nominal voltage frequency
Max.current
Max.power consumption
Protection class
/000 0VAC
00.00A
0.00 kW
IP 00
/0 /Hz
Made in Šiauliai, Lithuania
SKU000000
LN: LN000000 2019.01.01
Product name
Nominal voltage frequency
Max.current
Max.power consumption
Protection class
/000 0VAC
00.00A
0.00 kW
IP 00
/0 /Hz
Made in Šiauliai, Lithuania
SKU000000
LN: LN000000 2019.01.01
Product name
Nominal voltage frequency
Max.current
Max.power consumption
Protection class
/000 0VAC
00.00A
0.00 kW
IP 00
/0 /Hz
Made in Šiauliai, Lithuania
SKU000000
LN: LN000000 2019.01.01
Product name
Nominal voltage frequency
Max.current
Max.power consumption
Protection class
/000 0VAC
00.00A
0.00 kW
IP 00
/0 /Hz
Made in Šiauliai, Lithuania
SKU000000
LN: LN000000 2019.01.01
Figure 1.2 - VSA 3.0/VSA EKO technical lable place
Figure 1.3 - Indication for air ow direction.
GENERAL INFORMATION
Prior to the installation of the device it is necessary to read all the material presented in this document.
The device installation can be performed only by trained and qualied sta󰀨, familiar with this type of equipment installation, verication, maintenance
and required tools for installation works.
If the provided material is unclear or there are any doubts concerning safe installation and use, please contact the manufacturer or his representative.
The device can only work under following conditions.
It is strictly prohibited to use the device not for its purpose or not under provided working conditions without receiving a written permit from the
manufacturer or its representative.
In the event of failure, it must be reported to the manufacturer or its representative with the description of the failure and provide data on product label.
In the event of a failure, it is prohibited to repair, disassemble the device without a written consent from the manufacturer or its representative.
The device can be disassembled, repaired or modied only after receiving a written consent from the manufacturer or its representative.
Before using the products manufactured or supplied by the company, the clients must ensure the products are compatible with the selected en-
vironment.
TRANSPORTATION AND STORAGE
All devices are packed in the factory to withstand normal transportation conditions.
When unpacking the device, check if it has not been damaged during the transportation. It is prohibited to install damaged equipment!!!
The package is only a protection measure!
When unloading and storing the equipment, use proper lifting equipment to prevent damage and injuries. Do not lift the equipment on power ca-
bles, connection boxes, air collecting or disposal anges. Avoid shacking and punching overloads. Until the installation, store the devices in a dry
place where relative humidity does not exceed 70% (at 20°C), the average ambient temperature – between 5°C and +30°C. Storage place has to
be protected from dirt and water.
The devices have to be stored and transported only in a horizontal position so that the inlet ange would be at the bottom.
Storing for more than one year is not recommended. When storing longer than one year, it is necessary to verify if the bearings are rotating easily
before the installation (rotate the impeller by hand)
PURPOSE OF THE DEVICE
The device is used in ventilation and air conditioning systems to pull only clean air from the room (free from metal corroding chemicals; aggressive
substances for zinc, plastic, rubber; hard, sticky and brous particles).
DESCRIPTION
Fan rotation speed is controlled by changing voltage.
Maintenance undemanding bearings.
Automatic thermo contact engine protection.

EN | 3VSA 3.0_VSA EKO v2019.04
Painted hull (colour code RAL 9005)
WORKING CONDITIONS
It is prohibited to use the devices in potentially explosion hazardous environment.
The device is used to pull only clean air (free from metal corroding chemicals; aggressive substances for zinc, plastic, rubber; hard, sticky and
brous particles) from the room.
These devices do not use frequency converter.
Please note the maximum allowed ambient temperature.
PROTECTIVE MEASURES
Do not use this device for other than assigned purposes.
Do not disassemble or modify the device in any way. This may lead to mechanical failure or even injury.
When installing and maintaining the device, use special working clothing. Be careful – the corners and edges of the device can be sharp and
harmful.
Do not wear uttery clothing, which can be pulled into working fan, near the device
All products packed in the factory are not nally ready. The devices can only be used when connected to air duct or when the protective grid on
the collection and exhaust vents are installed.
Do not reach your ngers or other objects into air collection and exhaust protective grids or into the connected air duct. If any foreign body enters
the device, disconnect it from the electrical power source immediately. Before removing the foreign body, make sure that all the mechanical motion
has stopped inside the device. Also, make sure that an accidental turning on is not possible.
Avoid direct contact with collective and exhaustive air stream of the device.
Do not connect the device to a di󰀨erent power chain other than indicated on the device label on the device case.
Never use a damaged power cable.
Never take the power cables connected to the electricity with wet hands.
Never immerse the extension cables and plug connectors into the water.
Do not install and use the device on crooked stands, rugged surfaces and other unstable planes.
Never use this device in potentially explosive and having aggressive substances environment.
INSTALLATION
MECHANICAL CONNECTION
Installation works can only be performed by trained and qualied personnel.
The device should be mounted rmly and rigidly so it’s safe use would be ensured.
The device can be connected to pull the air directly from the ventilated room (g. 01) or from the air duct system (g. 02)
It is necessary to ensure protection from contacting working fan impeller (for this, specially produced accessories or required air duct length is
used)
Do not connect the elbows near the connection anges of the unit. The minimum distance of the straight air duct between the unit and the rst
branch of the air duct in the suction air duct must be 1xD, where D is diameter of the air duct.
When connecting the air ducts, pay attention to the air ow direction indicated on the device case.
The device is mounted onto chimney using accessories: reverse thrust valves, exible connectors, connection anges. They have to be installed
only as shown in g. 03.
When mounting, we recommend using exible connectors that reduce vibrations transmitted from the device to the air duct system and environ-
ment.
We recommend using air lters which reduce the accumulation of dirt on the fan impeller. Accumulated dirt misbalances the impeller and vibrations
appear. This can cause engine failure.
If there is a possibility for condensate or water to access the unit, external protective measures shall be tted.
Chimney skirt is mounted on roof above the prepared chamber which cannot be greater than its own internal chamber.
The skirt has to be rmly attached to the roof (g. 04).
The chimney has to be installed so that later mounted fan would be in a horizontal position.
The chimney is attached to the skirt with self-tapping screws through the prepared holes (g. 05).
Space between the chimney and skirt has to be sealed with waterproof material (g. 06).
The skirt must be covered with heat deterring substance (g. 07). Choose the isolating material with the most thermal resistance.
Cover the roof coating (g. 08).
The chimney must be rmly attached to the roof.
Space between the chimney and roof coating has to be sealed with waterproof material (g. 09).
Unscrew 4 fans cover screws and remove the cover (Fig. 10)
Power supply cord has to be pushed through plastic tube inside the chimney and conect to the fan.
Attach the fan to the roof chimney.
The roof fan is attached to the chimney using screws. It is necessary to use rubber transmissions.
When fan attached to the chimney, put back fan cover and screw it with 4 screws.

4 | EN VSA 3.0_VSA EKO v2019.04
01-02. VSA air duct conection
04-09. Kamino įrengimas montuojant VSA
10. VSA mounting
ELECTRIC INSTALLATION
The devices have rotating parts and are connected to the electricity. This may pose a risk to the human health and life. That is why safety require-
ments have to be followed while installing. If you have any doubts on the safety of the products installation and use, please contact the manufac-
turer or its representative.
Installation works may be performed only by trained and qualied personnel.

EN | 5VSA 3.0_VSA EKO v2019.04
Make sure that the electric power chain data complies with the data on the product label on the device case.
Selected power cord has to match device power.
The fan has to be connected according to the electric scheme which is described in this document and is shown under the electricity connection
box cap (g. 12).
It is necessary to connect an external protective device (an automatic switch or fuse) with a trigger current 1.5 times higher than the devices max-
imum current (indicated on the product label).
The unit must be adequately grounded.
If the device engine speed control regulator is used, be sure that it ensures safe activity of the engine.
It is necessary to ensure minimal engine speed at which the reverse thrust valves (if any) open.
Frequency converters for the speed control of these devices are not used.
WIRING DIAGRAM
YE/GN
BK
PE
NL
BN
N
TK TK
RD
RD
L
BU
YE/GN - yellow/green; BK - black,
RD - red; BN - braun; BU - blue,
SP1-L-0k
Protective earth PE, L1, N - line
voltage 230V
C
C - capacitor
TK - jumper TK - jumper
C - capacitor
C
PE, L1, N - line
voltage 230V
Protective earth
YE/GN - yellow/green; BK - black,
RD - red; BN - braun; BU - blue,
BU
L
RD
RD
TKTK
N
BN
LN
PE
BK
YE/GN
TK - jumper
C - capacitor
C
PE, L1, N - line
voltage 230V
Protective earth
YE/GN - yellow/green; BK - black,
RD - red; BN - braun; BU - blue,
BU
L
RD
RD
TKTK
N
BN
LN
PE
BK
YE/GNYE/GN
BK
PE
NL
BN
N
TK TK
RD
RD
L
BU
YE/GN - yellow/green; BK - black,
RD - red; BN - braun; BU - blue,
Protective earth PE, L1, N - line
voltage 230V
C
C - capacitor
TK - jumper
YE/GN
BK
PE
NL
BN
N
TK TK
RD
RD
L
BU
YE/GN - yellow/green; BK - black,
RD - red; BN - braun; BU - blue,
Protective earth PE, L1, N - line
voltage 230V
C
C - capacitor
TK - jumper TK - jumper
C - capacitor
C
PE, L1, N - line
voltage 230V
Protective earth
YE/GN - yellow/green; BK - black,
RD - red; BN - braun; BU - blue,
BU
L
RD
RD
TKTK
N
BN
LN
PE
BK
YE/GN
YE/GN
BK
PE
NL
BN
N
TK TK
RD
RD
L
BU
YE/GN - yellow/green; BK - black,
RD - red; BN - braun; BU - blue,
Protective earth PE, L1, N - line
voltage 230V
C
C - capacitor TK - jumper
YE/GN
BK
PE
NL
BN
N
TK TK
RD
RD
L
BU
YE/GN - yellow/green; BK - black,
RD - red; BN - braun; BU - blue,
Protective earth PE, L1, N - line
voltage 230V
C
C - capacitor TK - jumper TK - jumper C - capacitor
C
PE, L1, N - line
voltage 230V
Protective earth
YE/GN - yellow/green; BK - black,
RD - red; BN - braun; BU - blue,
BU
L
RD
RD
TKTK
N
BN
LN
PE
BK
YE/GN
YE/GN
BK
PE
NL
BN
N
TK TK
RD
RD
L
BU
YE/GN - yellow/green; BK - black,
RD - red; BN - braun; BU - blue,
Protective earth PE, L1, N - line
voltage 230V
C
C - capacitor
TK - jumper
YE/GN
BK
PE
NL
BN
N
TK TK
RD
RD
L
BU
YE/GN - yellow/green; BK - black,
RD - red; BN - braun; BU - blue,
Protective earth PE, L1, N - line
voltage 230V
C
C - capacitor
TK - jumper TK - jumper
C - capacitor
C
PE, L1, N - line
voltage 230V
Protective earth
YE/GN - yellow/green; BK - black,
RD - red; BN - braun; BU - blue,
BU
L
RD
RD
TKTK
N
BN
LN
PE
BK
YE/GN
SP1-L-0k SP1-L-0kSP1-L-0k
SP1-L-0k SP1-L-0k
SP1-L-0k SP1-L-0k SP1-L-0k
SP1-L-0k SP1-L-0k SP1-L-0k
YE/GN
BN
PE
NL
BU
N
TK TK
RD
RD
L
BK
YE/GN - yellow/green; BK - black,
RD - red; BN - braun; BU - blue,
SP2-L-0k
Protective earth PE, L1, N - line
voltage 230V
C
C - capacitor
TK - jumper
YE/GN
BN
PE
NL
BU
N
TK TK
RD
RD
L
BK
YE/GN - yellow/green; BK - black,
RD - red; BN - braun; BU - blue,
SP2-L-0k
Protective earth PE, L1, N - line
voltage 230V
C
C - capacitor
TK - jumper
YE/GN
BN
PE
NL
BU
N
TK TK
RD
RD
L
BK
YE/GN - yellow/green; BK - black,
RD - red; BN - braun; BU - blue,
SP2-L-0k
Protective earth PE, L1, N - line
voltage 230V
C
C - capacitor
TK - jumper
YE/GN
BN
PE
NL
BU
N
TK TK
RD
RD
L
BK
YE/GN - yellow/green; BK - black,
RD - red; BN - braun; BU - blue,
SP2-L-0k
Protective earth PE, L1, N - line
voltage 230V
C
C - capacitor
TK - jumper
YE/GN
BN
PE
NL
BU
N
TK TK
RD
RD
L
BK
YE/GN - yellow/green; BK - black,
RD - red; BN - braun; BU - blue,
SP2-L-0k
Protective earth PE, L1, N - line
voltage 230V
C
C - capacitor
TK - jumper
YE/GN
BN
PE
NL
BU
N
TK TK
RD
RD
L
BK
YE/GN - yellow/green; BK - black,
RD - red; BN - braun; BU - blue,
SP2-L-0k
Protective earth PE, L1, N - line
voltage 230V
C
C - capacitor
TK - jumper
YE/GN
BN
PE
NL
BU
N
TK TK
RD
RD
L
BK
YE/GN - yellow/green; BK - black,
RD - red; BN - braun; BU - blue,
SP2-L-0k
Protective earth PE, L1, N - line
voltage 230V
C
C - capacitor
TK - jumper
YE/GN
BN
PE
NL
BU
N
TK TK
RD
RD
L
BK
YE/GN - yellow/green; BK - black,
RD - red; BN - braun; BU - blue,
SP2-L-0k
Protective earth PE, L1, N - line
voltage 230V
C
C - capacitor
TK - jumper
YE/GN
BN
PE
NL
BU
N
TK TK
RD
RD
L
BK
YE/GN - yellow/green; BK - black,
RD - red; BN - braun; BU - blue,
SP2-L-0k
Protective earth PE, L1, N - line
voltage 230V
C
C - capacitor
TK - jumper
YE/GN
BN
PE
NL
BU
N
TK TK
RD
RD
L
BK
YE/GN - yellow/green; BK - black,
RD - red; BN - braun; BU - blue,
SP2-L-0k
Protective earth PE, L1, N - line
voltage 230V
C
C - capacitor
TK - jumper
YE/GN
BN
PE
NL
BU
N
TK TK
RD
RD
L
BK
YE/GN - yellow/green; BK - black,
RD - red; BN - braun; BU - blue,
SP2-L-0k
Protective earth PE, L1, N - line
voltage 230V
C
C - capacitor
TK - jumper
YE/GN
BN
PE
NL
BU
N
TK TK
RD
RD
L
BK
YE/GN - yellow/green; BK - black,
RD - red; BN - braun; BU - blue,
SP2-L-0k
Protective earth PE, L1, N - line
voltage 230V
C
C - capacitor
TK - jumper
#1 #2
GNYE BK RD BU BN
- green/yellow - black - red - blue - brown
#3 #4
PE BK BU BN YE WH RD
- green - yellow - black - blue - brown - yellow - white - red
P – protective earth,
L – phase, mains 50/60 Hz
N - neutral, mains 50/60 Hz
Analog in (0-10V DC/PWM) – speed setting via linear set value (0-10VDC) or PWM signal
Tacho out – tach output: 1 pulse per revolution
+10VDC OUT – voltage output +10V max. 1.1 mA
Alarm relay – NC, contact fermé; dans le cas de panne de vient ouvert
START-UP
The device can be started only by qualied and trained personnel.
Before starting the device, make sure that the power chain matches the data on the label.
Before starting the device, make sure that the device is connected to the power source in accordance with the scheme shown in this document
and under the electricity connection box cap.
Before starting the device, make sure that all the above listed security and installation instructions are arranged.
When the device is started, make sure that the engine rotates evenly, does not vibrate and does not emit strange noise.
When the device is started, it is necessary to verify that air ow of the device matches the air direction indicated on the case.
It is necessary to verify that the current used by the engine does not exceed the maximum current (indicated on the product label).
It is necessary to check whether the engine does not overheat.
It is prohibited to turn on and turn o󰀨 the fan so often that it would lead to engine windings overheating or isolation damage.
MAINTENANCE
Fan bearings do not require maintenance.
If there are no air lters before the fan, the only maintenance requirement of the fan is impeller cleaning. It is recommended to clean the impeller
at least once every six months.

6 | EN VSA 3.0_VSA EKO v2019.04
Before cleaning it is necessary to turn o󰀨 the power supply and block the switch to prevent accidental turning on while working.
It is necessary to wait until any mechanical motion stops, the engine cools down and the capacitors discharge.
Make sure that the fan and its parts and accessories are rmly and rigidly mounted.
The impeller has to be cleaned with caution in order not to damage the balance of the impeller.
It is strictly forbidden to use mechanical scrubs, chemicals, cleaners, compressed air stream or any liquids to clean the impeller.
It is prohibited to wash the fan with any liquids.
When the device’s maintenance is complete, mount it back to the air duct system performing same actions as pointed out in „installation“ and
„starting“ points and follow other requirements listed in this document.
DEFECTS AND THEIR ELIMINATION
Defect elimination works can only be performed by trained and qualied personnel.
If the device turns o󰀨, it is necessary to:
Check whether the network voltage and current meets the requirements indicated on the product label.
Check whether the electrical current reaches the device.
When the electrical power problems are eliminated, re-activate the device.
If the power current supply is in order but the device does not start, do the following:
Wait 10-20 min. until the engine cools down.
If the electrical current was not disconnected and after 10-20 min. the engine starts itself, this means that an automatic thermal protection was
triggered. It is necessary to look for engine overheating cause and eliminate it.
If the engine does not start after 10-20 min. do the following:
Disconnect the power supply.
Wait until any mechanical rotation stops, the engine cools down and the capacitors discharge.
Make sure that the impeller is not blocked.
Check the capacitor (for single-phase fans according to connection scheme). If the defects persist, replace the capacitor.
If that does not help, contact the supplier.
DIMENSIONS AND WEIGHT
M
M
VSA
øD H h L ød ød1 M M1 n m
[mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [kg]
190 L 3.0 344 207 107 305 177 6,1 96,5 123,5 245 4,4
190 S 3.0 344 207 107 305 177 6,1 96,5 123,5 245 4,4
220 M 3.0 450 214,55 109 405 230 7,1 138 168 330 6,7
220 S 3.0 450 214,35 109 405 203 7,1 138 168 330 6,7
225 L 3.0 450 245,55 109 405 230 7,1 138 168 330 7,6
250 L 3.0 450 245,55 109 405 230 7,1 138 168 330 7,9
190 EKO 344 234 107 305 177 M4 96,5 123,5 245 4,5
220 EKO 450 241 109 405 230 M5 138 168 330 7
225 EKO 450 245,5 109 405 230 M5 138 168 330 7,6
250 EKO 450 315 109 405 230 M5 138 168 330
TECHNICAL DATA
VSA 3.0 190 L 190 S 220 M 220 S 225 L 250 L
- phase/voltage [50 Hz/VAC] ~1,230 ~1, 230 ~1, 230 ~1, 230 ~1, 230 ~1, 230
- power [kW] 0,049 0,074 0,067 0,106 0,133 0,221

EN | 7VSA 3.0_VSA EKO v2019.04
- current [A] 0,2 0,31 0,28 0,45 0,6 0,94
- speed [min-1]2750 2800 2600 2800 2660 2700
- capacitor [µF] 4,0 2,0 4,0 2,0 4,0 5,0
- max. ambient tem-
perature [Co]55 55 75 75 85 70
- motor protection class IP-44 IP-44 IP-44 IP-44 IP-44 IP-44
- wiring diagram #2 #1 #2 #1 #1 #1
VSA EKO 190 220 225 250
- phase/voltage [50 Hz/VAC] ~1,230 ~1,230 ~1,230 ~1,230
- power [kW] 0,084 0,097 0,17 0,360
- current [A] 0,66 0,77 1,29 2,4
- speed [min-1]3150 2700 2860 3400
- capacitor [µF] - - - -
- max. ambient temperature [Co]60 60 60 60
- min. ambient temperature [Co]-25 -25 -25 -25
- motor protection class IP-44 IP-44 IP-44 IP-44
- wiring diagram #3 #3 #3 #4

8 | EN VSA 3.0_VSA EKO v2019.04
ECODESIGN DATA TABLE
VSA 190 L 3.0 190 S 3.0 220 M 3.0 220 S 3.0
Specic energy consumption (SEC) cold [ kWh/m2a ] -52,7 -51,8 -53,6 -52,3
Specic energy consumption (SEC) average [ kWh/m2a ] -25,6 -24,7 -26,6 -25,2
Specic energy consumption (SEC) warm [ kWh/m2a ] -10,1 -9,2 -11,1 -9,7
Declared typology Unidirectional Unidirectional Unidirectional Unidirectional
Type of drive installed (fan) Variable Variable Variable Variable
Type of heat recovery system N/A N/A N/A N/A
Thermal e󰀩ciency of heat recovery [ % ] N/A N/A N/A N/A
Maximum ow rate [ m3/h ] 350 216 670 335
Electric power input of the fan drive at maxi-
mum ow rate
[ W ] 74 49 106 67
Sound power level (Lwa) [ dB(A) ] 62 60 63 61
Reference ow [ m3/s ] 0,07 0,04 0,13 0,07
Reference pressure di󰀨erence [ Pa ] 50 50 50 50
SPI [ W/(m3/h) ] 0,16 0,22 0,11 0,19
Control factor and control typology 0,65 0,65 0,65 0,65
Declared maximum internal leakage rates [ % ] N/A N/A N/A N/A
Declared maximum external leakage rates [ % ] <1 <1 <1 <1
Possition and description of visual lter warn-
ing for RVU’s
N/A N/A N/A N/A
AEC average [ kWh ] 107 143 70 123
AEC cold [ kWh ] 107 143 70 123
AEC warm [ kWh ] 107 143 70 123
AHS Average [ kWh/a ] 2830 2830 2830 2830
AHS Cold [ kWh/a ] 5536 5536 5536 5536
AHS Warm [ kWh/a ] 1280 1280 1280 1280
ErP Compliance 2018 2018 2018 2018
Internet address for disassembly instructions www.salda lt
VSA 225 L 3.0 250 L 3.0 190 EKO 220 EKO 225 EKO 250 EKO
Declared typology Unidirec-
tional
Unidirec-
tional
Unidirec-
tional
Unidirec-
tional
Unidirec-
tional
Unidirec-
tional
Type of drive External
MSD or
VSD
External
MSD or
VSD
External
MSD or
VSD
External
MSD or
VSD
External
MSD or
VSD
External
MSD or
VSD
Type of HRS N/A N/A N/A N/A N/A N/A
Nominal NRVU ow rate [ m3/s ] 0,15 0,15 0,08 0,12 0,15 0,28
E󰀨ective electric power input [ kW ] 0,13 0,21 0,08 0,1 0,16 0,36
SFPint [ W/(m3/s) ] N/A N/A N/A N/A N/A N/A
Face velocity [ m/s ] 000000
Normal external pressure [ Pa ] 316 461 361 278 472 481
Internal pressure drop of ventilation compo-
nents
[ Pa ] N/A N/A N/A N/A N/A N/A
Static e󰀩ciency of fans used in accordance
with Regulation No 327/2011
[ % ] 34,9 32,4 36,9 34,8 43,1 37
Declared maximum external leakage [ % ] <1 <1 <1 <1 <1 <1
Casing sound power level (Lwa) [ dB(A) ] 73 75 72 73 79 82
ErP Compliance 2018 2018 2018 2018 2018 2018
Internet address for disassembly instructions www.salda lt

EN | 9VSA 3.0_VSA EKO v2019.04
DECLARATION OF CONFOMITY
Manufacturer
SALDA, UAB
Ragainės g. 100
LT-78109 Šiauliai, Lithuania
Tel.: [phone]
www.salda.lt
Hereby conrms that the following products - Air handling units:
Fan*
(where by “*” indicates possible unit installation type and modication)
Provided it was delivered and installed in the facility in accordance with the included installation instructions, comply
with all applicable requirements in the following directives:
Machinery Directive 2006/42/EC
Low Voltage Directive 2006/95/EC
EMC Directive 2014/30/EU
The following regulations are applied in applicable parts:
Ecodesign requirements for ventilation units Nr. 1253/2014;
Energy labeling of residential units Nr. 1254/2014.
The following harmonized standards are applied in applicable parts:
LST EN ISO 12100 - Safety of machinery - General principles for design - Risk assessment and risk reduction.
LST EN 60204-1 - Safety of machinery - Electrical equipment of machines - Part 1: General requirements.
LST EN 60335-1 - Household and similar electrical appliances. Safety. Part 1: General requirements.
LST EN 60529 - Degrees of protection provided by enclosures (IP code).
LST EN 60034-5 - Rotating electrical machines. Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP
code)
LST EN 61000-6-2 - Electromagnetic compatibility (EMC) -- Part 6-2: Generic standards - Immunity for industrial environments.
LST EN 61000-6-3 - Electromagnetic compatibility (EMC) -- Part 6-3: Generic standards - Emission standard for residential, commercial and
light-industrial environments.
Should any alterations be made in the products, this declaration will no longer apply.
Notied body: VšĮ Technikos priežiūros tarnyba, Naugarduko g. 41, LT – 03227 Vilnius, Lithuania, identication number 1399.
Quality: Salda UAB activities are in line with the international quality management system standard ISO 9001:2015.
Date 2019-02-01
Giedrius Taujenis
Director product development

10 | EN VSA 3.0_VSA EKO v2019.04
WARRANTY
1. All equipment manufactured in our factory is checked in operating conditions and tested befor delivery. Test protocol is supplied together with
the unit. The equipment is shipped in good working order and condition to the direct client. The unit is warrantied for the period of two years from
the invoice date.
2. If equipment is found to have been damaged during transportation, a claim should be made against carrier, as we assume no responsibility for
such damage.
3. This warranty does not apply:
3.1. when transportation, storage, installation and maintenance instructions of the unit are violated;
3.2. when the equipment is improperly maintained, mounted - inadequate maintenance;
3.3. when the equipment without our knowledge and permission has been upgraded or unskilled repairs were made;
3.4. when the unit was used not for its original purpose.
3.5. Company SALDA UAB is not responsible for potential loss of property or personal injury in cases where AHU is manufactured without a con-
trol system and the control system will be installed by the client or third parties. The manufacturer’s warranty does not cover devices that will be
damaged by installing the control system.
4. This warranty does not apply at these malfunction cases:
4.1. mechanical damage;
4.2. damage caused by entering outside objects, materials, liquids;
4.3. damage caused by natural disaster, accident (voltage change in the electricity network, lightning, etc..).
5. The company assumes no liability for its products either directly or indirectly damage, if the damage is caused by failure to comply with instal-
lation and mounting regulations, deliberate or careless users or third-party behavior.
These conditions are readily discernable when the equipment is returned to our factory for inspection.
If the direct client determines that equipment is found to be faulty, or a breakdown occurred, he should inform the manufacturer within ve working
days and deliver the equipment to manufacturer. Delivery costs should be covered by customer.
Manufacturer reserves the right to change this technical passport any time without prior notice, if some typographic
errors or inaccurate information is found, as well as after improving the apps and/or the devices. Such changes will be
included in the new issues of the technical passport. All illustrations are just for information and thus may di󰀨er from the
original device.
20.1. LIMITED WARRANTY COUPON
Warranty term
24 months*
I received complete package and technical manual of the product ready for usage. I have read warranty terms and conditions and agree with them:
..........................................................................................................................................................................
Customer’s signature
*refer to WARRANTY CONDITIONS
Dear User, we appreciate your choice and do hereby guarantee that all ventilation equipment manufactured by our Company is inspected and
thoroughly tested. An operational and high-quality product is sold to the direct buyer and shipped from the territory of the factory. It is provided with
a 24-month warranty since invoice issue date.
Your opinion is important to us, thus we always look forward to hearing your comments, feedback, or suggestions regarding technical and opera-
tional characteristics of the Products.
In order to avoid any misunderstandings, please read the instructions for installation and operation of the product as well as other technical docu-
ments of the product carefully. The number of the Limited Warranty Coupon and serial number of the product specied on the silver identication
sticker attached to the housing must match.
The Limited Warranty Coupon shall be valid provided that the seller’s stamps and records are clear. It is prohibited to change, delete, or rewrite
the data specied on it in any manner – such a coupon shall be invalid.
With this Limited Warranty Coupon the manufacturer conrms one’s obligations to implement the imperative requirements established by eective
laws on protection of consumer rights in the event of identication of any defects of the products.
The manufacturer reserves the right to refuse provision of free warranty servicing in cases when the warranty conditions listed below are disre-
garded.

| 11VSA 3.0_VSA EKO v2019.04

Ragainės g. 100
Šiauliai LT-78109, LITHUANIA
[phone]
offi[email protected]
MAN000152
MAN000152
UNIT’S MAINTENANCE TABLE
Product name*
lot number*
Instalation Interval Date
Fan cleaning Once a year**
Heat exchanger cleaning Once a year**
Filter replacement Every 3-4
months**
* - Look at the product label.
** - At least.
NOTE. The purchaser is required to ll in the “Product maintenance table”.