Samsung MWR-WH00 User manual

INSTALLATION
MANUAL
Wired Remote Controller
MWR-WH00
System Air Conditioner
DB98-31218A(2)SE F I DP G R A
ESPAÑOLFRANÇAISITALIANOPORTUGUÊSDEUTSCHEΛΛHNIKARUSSIAN ENGLISH
MWR-WH00_IM_E_31218-2.indd 33 2010-02-25 ｿﾀﾈﾄ 1:54:32

E-2
Safety Precautions
Read carefully this installation manual before
installation and check if the wired remote controller is
installed correctly after installation.
 Do not attempt to install or repair this wired remote
controller by yourself.
This wired remote controller contains no user-serviceable
parts. Always consult authorized service personnel for
repairs.
When moving, consult authorized service personnel
for disconnection and installation of the wired remote
controller.
Ensure that the wall is strong enough to support the weight
of the wired remote controller.
Must install the wired remote controller with rated power
supply.
The wired remote controller must be installed according to
the national electrical rules by an installation specialist.
If you wish to uninstall the wired remote controller, consult
an authorized installation center.
WARNING
CAUTION
 Do not use inflammable gases near the wired remote
controller.
Do not install the wired remote controller in a location
where it will come into contact with combustible gases,
machine oil, sulphide gas, etc.
Avoid locations where acid/alkali solution or special spray
is used.
Choose a location that is dry and sunny, but not exposed to
direct sunlight. Suitable temperature is between
0°C(32°F) and 39°C(102°F) .
 Do not spill water into the wired remote controller.
Do not apply tensile strength to the cable to avoid cable
damage.
Do not press the buttons with a sharp object.
Do not connect the power cable to the control terminal.
If the wired remote controller is installed in a hospital or
other special places, it should not affect other electronic
devices.
This installation manual describes how to install the wired remote controller.
For installation of other optional accessories, refer to the appropriate installation
manual.
MWR-WH00_IM_E_31219-1.indd 2 2009-12-14 ｿﾀﾀ・9:01:27

E-3
ENGLISH
Contents
 WIRED REMOTE CONTROLLER AND ACCESSORIES ................................................................................... 4
Accessories .............................................................................................................................................. 4
Dimension ............................................................................................................................................... 4
 INSTALLING THE WIRED REMOTE CONTROLLER ........................................................................................ 5
Installing the Power Supply Cables inside of Indoor Unit ............................................... 5
Installation ............................................................................................................................................... 6
Setting the Wired remote controller Options ........................................................................ 7
Wired remote controller Error Codes ......................................................................................... 8
Indoor Unit Tracking with the Wired remote controller ................................................ 10
Connecting the Wired remote controller .............................................................................. 11
 ADDITIONAL FUNCTIONS .......................................................................................................................... 14
Service Mode ....................................................................................................................................... 14
Monitoring and Setting the Indoor Unit Option Code ................................................... 15
Monitoring the Indoor Unit Main/Group Address ............................................................ 16
Monitoring the Indoor Unit Cycle Data .................................................................................. 17
 Monitoring and Setting the Indoor Temperature
Compensation for the Wired remote controller ................................................................. 18
Monitoring the RPM Compensation ........................................................................................ 19
 Monitoring the EEV Step for the Stopped
Indoor Unit during the Heating Mode .................................................................................... 20
Monitoring the Filter Time Setting ............................................................................................ 21
 Monitoring the Temperature Compensation Value
under the Heating Mode ............................................................................................................... 22
Checking the Central Control Usage ........................................................................................ 23
Checking the Drain Pump Usage .............................................................................................. 24
Checking the Electric Heater Usage ......................................................................................... 25
Checking the Water Coil Usage .................................................................................................. 26
Checking the External Control Usage ..................................................................................... 27
Checking the Connected Indoor Unit/ERV Quantity ....................................................... 28
Checking the Wired remote controller PCB Settings ....................................................... 29
Checking the Wired remote controller Software Version .............................................. 30
Note  The illustrations will help you to understand the
symbols displayed in the pictures.
 The illustrations in the step-by-step procedures use
3 different symbols:
PRESS PUSH HOLD DOWN
MWR-WH00_IM_E_31219-1.indd 3 2009-12-14 ｿﾀﾀ・9:01:28

E-4
Wired remote controller and Accessories
Accessories
The following accessories are supplied with the air conditioner.

The number of each accessory is indicated in parentheses.
Dimension
(Unit : mm)
 The wired remote controller should be installed by a trained installer.
 Make sure the main power is off before installing the wired remote
controller.
 The cables must be installed according to the national wiring
regulations and inside the wall for safety reasons.
Cable Tie (2) Cable Clamp(4) M4X16 Screw(5)
Power cable for
indoor unit
(1)
Communication cable
for indoor unit (1)
Wire joint (4) User's manual (1) Installation manual(1) 10m Connecting
wire (1)
MWR-WH00_IM_E_31218-2.indd 4 2010-02-25 ｿﾀﾈﾄ 1:54:33

E-5
ENGLISH
Installing the Wired remote controller
Installing the Power Cables inside of Indoor Unit
This is an explanation of power supply cable and communication cable.
Make sure that you read this thoroughly before installation.
Connector type cable connection
Terminal type cable connection
AC Power supply
Check the wire colors.
The wires are color-coded.
Power cable for the
indoor unit
Communication cable for
the indoor unit (COM2)
White
Black
Red
Blue
F3
F4
White
Black
Red
Blue Blue 2P
(2.5 pitch)
White 2P
(2.5 pitch)
Indoor
unit PCB
White 2P
(2.5 pitch)
Blue 2P
(2.5 pitch)
Indoor unit terminal block
AC Power supply
Check the wire colors.
The wires are color-coded.
Power cable for the
indoor unit
Communication cable for
the indoor unit (COM2)
White
Black Red
Blue Blue 2P
(2.5 pitch)
White 2P
(2.5 pitch)
Indoor
unit PCB
White 2P
(2.5 pitch)
Blue 2P
(2.5 pitch)
White
Black
Red
Blue
Indoor unit terminal block
1 way cassette indoor unit does not contain the power cable.
In this case, use the power cable which is provided with the
wired remote controller.
MWR-WH00_IM_E_31219-1.indd 5 2009-12-14 ｿﾀﾀ・9:01:29

E-6
Installing the Wired remote controller (Continued)
1Open the wired remote controller by pushing up the top cover of the remote controller while
holding the rear cover firmly. The wired remote controller opens in the way of slide.
2Install the rear cover of the wired remote controller on the wall with the supplied screws. After
that, arrange the power cables on rear side of the front cover.
3Connect the yellow and orange wires from the wired remote controller to the power cable
(V1, V2) of indoor unit. Connect the red and blue wires to the communication cable (F3, F4) of
indoor unit.
4 Reassemble the wired remote controller.
When you reassemble the wired remote controller, match the grooves on the left side.
Installation
More than
30mm
Screw hole
Rear cover
 Before fixing the rear cover, clear
30mm of space on the top and
60mm on the right side.
 Fasten the screw in the screw hole.
Front cover
More than
60mm
Connector type cable connection Terminal type cable connection
 When using an extension cable, make sure that the communication cable and the
power cable is installed separately.
(If not, it may cause malfunction of the wired remote controller.)
 Power cable of the wired remote controller(V1,V2) should be connected to the one
indoor unit only.
Housing
Tighten the
cable with the
wire joint
(accessories)
tightly.
Indoor unit
Multi function
wired remote
controller
Communication
cable(F3, F4)
F3 F4
Power cable
(V1, V2)
Indoor unit
Multi function
wired remote
controller
Communication
cable(F3, F4)
Power cable
(V1, V2)
MWR-WH00_IM_E_31218-2.indd 6 2010-02-25 ｿﾀﾈﾄ 1:54:34

E-7
ENGLISH
 Default settings
 After changing the setting of PCB, make sure to initialize
the system.
 - To initialize the system, press the , buttons
at the same time for 5 seconds.
 If the indoor unit does not support SW5 and SW6
options, indoor unit temperature sensor will be used
regardless of the settings.
 You can check the wired remote controller DIP switch
settings in menu 15 of additional functions. (Refer to
page 29)
- You can check it without disassembling the product.
Installing the Wired remote controller (Continued)
Setting the Wired Remote Controller Options
Switch
No. Switch OFF Switch ON
SW1 Cooling and Heating Cooling Only
SW2 Allow wireless remote
controller
Disable the wireless remote
controller
SW3 Master remote
controller Slave remote controller
SW4 Temperature display : °C Temperature display : °F
SW5
Use the indoor unit
Temperature Sensor for the
indoor unit control
Use the wired remote
controller Temperature
Sensor for the indoor unit
control
SW6 -
Use the average of the
indoor unit sensor and the
wired remote controller
sensor for the indoor unit
control
SW7 Auto mode enable Auto mode disable
SW8 - -

       
      
MWR-WH00_IM_E_31219-1.indd 7 2009-12-14 ｿﾀﾀ・9:01:32

E-8
Installing the Wired remote controller (Continued)
Wired remote controller Error Codes
The error codes of the wired remote controller, indoor unit,
outdoor unit are displayed on the LCD display.
Refer to the indoor and outdoor unit technical manuals for the error
codes reference.
When the indoor/outdoor unit error occurs
  Main(COM1) address(A) of the indoor unit where error occurred
and error code are displayed in turns.
Ex) 101 error occurred in #28 indoor unit
Indoor unit
<LCD display>
When the wired remote controller error occurs
  Error code is displayed only. (Address will not be displayed.)
Ex) 601 error occurred in the wired remote controller
MWR-WH00_IM_E_31219-1.indd 8 2009-12-14 ｿﾀﾀ・9:01:33

E-9
ENGLISH
Installing the Wired remote controller (Continued)
Error display priority
  Priority 1: Wired remote controller error > Indoor/Outdoor unit error
Priority 2: Displays master indoor unit error
(Master Indoor unit = Indoor unit whose option switch K10 is set OFF)
Priority 3: Displays the error code of the indoor unit which has earlier Main(COM1) address
Priority 4: Displays the error code of the indoor unit which has earlier COM2 address
when Main(COM1) addresses is overlapped
Display Explanation Remark
- Master error of several units.
- Error occurs when 2 wired remote controllers are set as Master and
installed in one communication cable.
If communication cable is connected to opposite polarity,
detection is impossible.
- Error is detected only in Master wired remote controller.
- Error of independent ERV installation.
- When ERV is installed without an indoor unit.
- Error is detected only in Master wired remote controller.
- Slave wired remote controller installation error.
- When 2 slave wired remote controllers are installed.
- When 1 wired remote controller and 2 slave ERV remote controllers
are installed together.
Communication Tracking Error.
- MaterSlave wired remote controller communication error.
- Error is detected only in Slave wired remote controller.
Wired remote controllerindoor unit/ERV communication error.
Temperature OPEN/SHORT error.
FRAM READ/WRITE error.
- Mixed installation of Celsius(°C)/Fahrenheit(°F) indoor unit error.
- Error occurs when indoor units with Celsius(°C)/Fahrenheit(°F)
settings are installed together.
- Error is detected only in Master wired remote controller.
- Celsius(°C)/Fahrenheit(°F) setting error of the wired remote
controller.
- Error occurs when the indoor unit is set as Celsius and the wired
remote controller is set as Fahrenheit or vise versa.
- Change the setting of DIP switch 4 when the 620 error occurs.
High Priority
Low Priority
Refer to the installation manual of each device(Indoor/
Outdoor Unit) for error code references.
MWR-WH00_IM_E_31219-1.indd 9 2009-12-14 ｿﾀﾀ・9:01:33

E-10
Indoor Unit Tracking with the Wired remote
controller
1Tracking is started automatically after connecting to the
power.
2
To execute tracking again after the installation, press the
and buttons at the same time for 5 seconds.
 System is initialized and tracking will re-start.
3 Total quantity of searched indoor unit is displayed when
tracking.
 If the wired remote controller system needs to be
resetted, press the and buttons at the same
time for 5 seconds.
 Total quantity of indoor unit will be displayed in Master
wired remote controller.
- Slave wired remote controller will not display the
total quantity.
Installing the Wired remote controller (Continued)
<LCD display>
Total
quantity of
searched
units
Tracking in
progress
MWR-WH00_IM_E_31219-1.indd 10 2009-12-14 ｿﾀﾀ・9:01:34

E-11
ENGLISH
Installing the Wired remote controller (Continued)
Connecting the Wired remote controller
Individual Control
  Using one wired remote controller for one indoor unit.
Outdoor unit
Indoor unit
COM1(F1, F2)
COM2(F3, F4)
COM1(F1, F2)
COM2(F3, F4) COM2(F3, F4)
Wired remote controller
RMC:0 RMC:1 RMC:2
 The wired remote controller controls the indoor units,
connected to COM2 communication cable, individually
regardless of the RMC address.
 Power cable(V1,V2) does not connect between indoor
units.
MWR-WH00_IM_E_31219-1.indd 11 2009-12-14 ｿﾀﾀ・9:01:34

E-12
Installing the Wired remote controller (Continued)
RMC:2
Group Control - indoor units only
Using one wired remote controller for a group of indoor units.
  Group control of 3 indoor units with one wired remote controller
Outdoor unit
Indoor unit
COM1(F1, F2) COM1(F1, F2)
Wired remote controller
COM2(F3, F4) COM2(F3, F4)
COM1(F1, F2)
Outdoor unit
Indoor unit
Wired remote controller
Outdoor unit
Indoor unit
COM1(F1, F2)
COM1(F1, F2)
COM2(F3, F4)
COM2(F3, F4)
RMC:0 RMC:1
  Group control of indoor units which is connected to other outdoor unit with one wired
remote controller
RMC:1
RMC:0
 The wired remote controller controls the indoor units, connected to COM2
communication cable, in group regardless of the RMC address.
 Maximum 16 indoor units can be controlled as a group.
 Power cable(V1,V2) does not connect between indoor units.
 Power cable(V1,V2) should be connected to one indoor unit only.
MWR-WH00_IM_E_31219-1.indd 12 2009-12-14 ｿﾀﾀ・9:01:35

E-13
ENGLISH
Installing the Wired remote controller (Continued)
Using 2 wired remote controllers-indoor units only
2 wired remote controllers can be used to control a single indoor unit or a group of indoor units.
Using 1 MWR-WH00 and 1 MWR-WE00 - Indoor unit and ERV together
1
SW1 SW2 SW3 SW4 SW5 SW6 SW7 SW8
2 3 4 5 6 7 8 1
SW1 SW2 SW3 SW4 SW5 SW6 SW7 SW8
2 3 4 5 6 7 8
1
SW1 SW2 SW3 SW4 SW5 SW6 SW7 SW8
2 3 4 5 6 7 8 1
SW1 SW2 SW3 SW4 SW5 SW6 SW7 SW8
2 3 4 5 6 7 8
Outdoor unit
Indoor unit
Wired remote
controller
(Master)
COM2(F3, F4)
COM1(F1, F2)
Wired remote controller
(Slave)
Outdoor unit
Indoor unit
MWR-WH00 (Master)
- Controls indoor unit only
COM2(F3, F4)
COM1(F1, F2)
MWR-WE00 (Slave)
- Controls indoor unit and ERV
COM2(F3, F4) ERV
 2-wired remote controller controls the indoor units, connected to COM2
communication cable, regardless of the RMC address.
 The ERV is not connected to the MWR-WH00 individually.
 MWR-WE00 and MWR-WH00 are set as Master or Slave remote controller
without order.
 MWR-WH00 is not connected with MWR-BS00, MWR-TH01 and MWR-SH00.
MWR-WH00_IM_E_31219-1.indd 13 2009-12-14 ｿﾀﾀ・9:01:35

E-14
Additional Functions
Service Mode
 The wired remote controller supports the following service modes.
Menu Description
Monitoring and Setting the Indoor Unit Option Code
Monitoring the Indoor Unit Main/Group Address
Monitoring the Indoor Unit Cycle Data
Monitoring and Setting the Indoor Temperature Compensation for the Wired
remote controller
Monitoring the RPM Compensation
Monitoring the EEV Step for the Stopped Indoor Unit during Heating Mode
Monitoring the Filter Time Setting
Monitoring the Temperature Compensation Value under Heating Mode
Checking the Centralized Control Usage
Checking the Drain Pump Usage
Checking the Electric Heater Usage
Checking the Water Coil Usage
Checking the External Control Usage
Checking the Connected Indoor Unit Quantity
Checking the Wired remote controller PCB Settings
Checking the Wired remote controller Software Version
  In order to access the service mode, hold down the and buttons at the same
time for 3 seconds.
  Master indoor unit: Indoor unit with the K10 off
Indoor unit with the earliest Main(COM1) address
In case of the Main(COM1) address is repeated, master indoor unit is
selected by random.
 All the displayed information in service mode is the information of Master
indoor unit. Only the Master indoor unit’s information will be displayed when
more than 2 indoor units are connected.
 If the wired remote controller is connected to an indoor unit which does not
support additional functions, only following functions will be available:
- Menu No.4, No.14, No.15 and No.16.
 will be displayed if the indoor unit does not support the function.
MWR-WH00_IM_E_31219-1.indd 14 2009-12-14 ｿﾀﾀ・9:01:36

E-15
ENGLISH
Additional Functions
Monitoring and Setting the Indoor Unit
Option Code
In order to monitor and set the indoor unit option code using
the wired remote controller, hold down the and
buttons at the same time for 5 seconds.
1
The menu will display .
Press the
button to enter the indoor unit option code
mode.
Note The first digit represents the page number and
the remaining five digits are option codes.
2
Press the button to change the page. You can change
the page from 0 to 3.
3Press the buttons and the button to set the
option code in order.
Note The option code which is currently setting will
flicker.
4 Press the button to save the changed setting.
You will move to the menu selection display.
Note Press the button anytime during setup to exit
without setting.
 Option code will not be applied if you don’t press the
button.
 Setting indoor unit option code is only possible in
Master wired remote controller.
You can only check the indoor unit option code in Slave
wired remote controller.
 Setting indoor unit option code is possible when one
indoor unit is connected. If more than 2 indoor units are
connected, you can only check the Master indoor unit
option code.
Page No.
Option code
MWR-WH00_IM_E_31219-1.indd 15 2009-12-14 ｿﾀﾀ・9:01:38

E-16
Additional Functions (Continued)
Monitoring the Indoor Unit Main/Group
Address
In order to monitor the indoor unit Main/Group Address using
the wired remote controller, hold down the and
buttons at the same time for 5 seconds.
1
The menu will display .
Press the button and the menu will display .
2
Press the button. The main address (decimal notation)
and group address (hexadecimal notation) of currently set
indoor unit will be displayed.
3 Press the button to exit.
You will move to the menu selection display.
Note Press the button anytime during setup to exit
without setting.
Menu No.
Indoor unit
main address Indoor unit RMC address
MWR-WH00_IM_E_31219-1.indd 16 2009-12-14 ｿﾀﾀ・9:01:39

E-17
ENGLISH
Additional Functions (Continued)
Monitoring the Indoor Unit Cycle Data
In order to monitor the indoor unit cycle data using the wired
remote controller, hold down the and buttons at the
same time for 5 seconds.
1
The menu will display .
Press the button twice and the menu will display .
2
Press the button.
The current set temperature(data #1) will be displayed.
3
Select the desired menu from 4 digits by using the
buttons.
The first digit represents the menu and the remaining
three digits are used for data display.
4
Press the button to exit.
You will move to the menu selection display.
Note Press the button anytime during setup to exit
without setting.
Data No. Data
Indoor temperature(°C)
EVA-IN temperature(°C)
EVA -OUT temperature(°C)
Indoor unit’s EEV step
Menu No.
Data No. Cycle Data
MWR-WH00_IM_E_31219-1.indd 17 2009-12-14 ｿﾀﾀ・9:01:41

E-18
Additional Functions (Continued)
Monitoring and Setting the Indoor Temperature
Compensation for the Wired remote controller
In order to monitor and set the indoor temperature
compensation using the wired remote controller, hold down the
and buttons at the same time for 5 seconds.
1
The menu will display .
Press the button until is displayed.
2
Press the button.
The positive and decimal value of indoor temperature of
indoor unit will be displayed in turns. The set compensation
value will flicker.
3
Press the buttons to set the compensation value.
Note  The temperature will be adjusted by
0.1°C(0.1°F) when the buttons are
pressed.
 The compensation value range can be set is
between –9.9°C~ 9.9°C.
4
Press the button to save the changed setting.
You will move to the menu selection display.
Note Press the button anytime during setup to exit
without setting.
Current Temp.
(24.1°C)
Compensation value
(+2.3°C)
Menu No.
The compensation value will be maintained even after
initialization.
MWR-WH00_IM_E_31219-1.indd 18 2009-12-14 ｿﾀﾀ・9:01:42

E-19
ENGLISH
Additional Functions (Continued)
Monitoring the RPM Compensation
In order to compensate for the RPM using the wired remote
controller, hold down the and buttons at the same
time for 5 seconds.
1
The menu will display .
Press the button until is displayed.
2
Press the button.
The current indoor unit Fan RPM compensation setting state
will be displayed.
3
Press the button to exit.
You will move to the menu selection display.
Note Press the button anytime during setup to exit
without setting.
Value Data
RPM compensation used
(Indoor unit Dip switch K3: Off)
No RPM compensation used
(Indoor unit Dip switch K3: On (Default))
Menu No.
Set value
MWR-WH00_IM_E_31219-1.indd 19 2009-12-14 ｿﾀﾀ・9:01:44

E-20
Additional Functions (Continued)
Menu No.
Set value
Monitoring the EEV Step for the Stopped
Indoor Unit during the Heating Mode
In order to monitor EEV step when the indoor unit is off during
heating mode using the wired remote controller, hold down the
and buttons at the same time for 5 seconds.
1
The menu will display .
Press the button until is displayed.
2
Press the button.
The current indoor unit setting EEV step for the stopped
indoor unit during heating mode will be displayed.
3
Press the button to exit.
You will move to the menu selection display.
Note Press the button anytime during setup to exit
without setting.
Value Data
0 or 80 steps Auto compensation
(Indoor unit Dip switch K9: Off)
Fixed step to 80(Indoor unit Dip switch
K9: On (Default))
MWR-WH00_IM_E_31219-1.indd 20 2009-12-14 ｿﾀﾀ・9:01:45