Samsung MWR-WH02 User manual

Wired Remote Control
MWR-WH02
DB98-33323A(1)
IFSE P G Ne Po Hu ARD
Air Conditioner
user manual
imagine the possibilities
Thank you for purchasing this Samsung product.
MWR-WH02_IB_E_33323-1.indd 21 2011-01-10 오후 1:13:51

E-2
Safety Precautions
 Do not attempt to install or repair this wired remote
controller by yourself.
 This remote controller contains no user-serviceable parts.
Always consult authorized service personnel for repairs.
 When moving, consult authorized service personnel for
disconnection and installation of the remote controller.
 Ensure that the wall is strong enough to support the
weight of the remote controller.
 Must install the remote controller with rated power
supply.
 In the event of a malfunction (burning smell, etc.),
immediately stop operation, turn off the electrical
breaker, and consult authorized service personnel.
WARNING
CAUTION
 Do not use inflammable gases near the remote
controller.
 Do not spill water into the wired remote controller.
 Do not operate the remote controller with wet hands.
 Do not install the remote controller in a location where
it will come into contact with the combustible gases,
machine oil, sulphide gas, etc.
 Do not press buttons with a pointed thing.
 Do not pull or bend the wired remote controller cable
excessively.
 Do not use this wired remote controller for other
purpose.
 Do not spray an insecticide or other combustible things
on the wired remote controller.
 Do not clean the wired remote controller with benzene,
solvents or other chemicals.
 Do not give a shock to the wired remote controller or
disassemble it by yourself.
• Before using the wired remote controller, read carefully these instructions.
• After reading the instructions, keep this user's manual in a handy and safe place.
If a user is changed, you must hand over the manuals.
• Never attempt to install the air conditioning system or to move the wired remote
controller by yourself.
MWR-WH02_IB_E_33323-1.indd 2 2011-01-10 오후 1:13:27

E-3
ENGLISH
Contents

Wired remote controller
......................................................... 4

GettinG Started
........................................................................... 5

SelectinG the automatic operatinG mode
.......................... 6

SelectinG the coolinG mode
.................................................... 7

SelectinG the dry mode
............................................................ 8

SelectinG the Fan mode
............................................................. 9

SelectinG the heatinG mode
.................................................... 10

SelectinG the Quiet mode
......................................................... 11

SelectinG the Sleep mode
.......................................................... 12

adjuStinG the air SWinG direction
........................................ 13

checkinG the room temperature
............................................ 14

lockinG the Wired remote controller
...................................... 14

SettinG the on timer
................................................................... 15

SettinG the oFF timer
................................................................. 16

SettinG the auto Stop Function
............................................. 17

SettinG the temperature limitS
................................................ 18

lockinG the partS oF the Wired remote controller
......... 19
MWR-WH02_IB_E_33323-1.indd 3 2011-01-10 오후 1:13:27

E-4
Wired remote controller
The wired remote controller is installed on the wall.
Note  DIP switch setting is recognized during the initialization. If any changes are
mode to the DIP switch setting after the initialization, you have to initialize
the system by pressing and or reset the power.
 Press the button after cleaning the air filter. sign will be off.
The remote controller will display the filter sign to alert the user to clean the
filter and turn off the display when the button are pressed.
 will be displayed if you press the button of the function that the
indoor unit does not support.
 If the indoor unit does not support Set temperature display,
Set temperature is not displayed on remote controller.
ON/OFF timer/
Error Status display
Operation mode
display
Fan speed/
Air swing display
Special function
display
ON/OFF time setup
Swing button
Room temperature
check button
Filter Reset button
Temperature
display
Operation ON/OFF button
Temperature setting
button
Fan speed setting
button
Mode selection
MWR-WH02_IB_E_33323-1.indd 4 2011-01-10 오후 1:13:28

E-5
ENGLISH
Getting Started
You have just purchased a wired remote controller and it has been installed
by your installation specialist.
Your User’s Manual contain much valuable information on using
your wired remote controller. Please take the time to read them as they will
help you take full advantage of the unit’s features.
In the manual, you will find a series of step-by-step procedures for each
function available.
The illustrations in the step-by-step procedures use 3 different symbols:
PRESS PUSH HOLD DOWN
MWR-WH02_IB_E_33323-1.indd 5 2011-01-10 오후 1:13:28

E-6
The room temperature and the fan speed are controlled
automatically in the auto mode.
1
Press the (ON/OFF) button to turn on the indoor unit.
- Do not press the (ON/OFF) button if the remote
controller is on.
Result: The air conditioner will be turned on with the
most recently used mode.
The air conditioner has a built-in protection
mechanism to prevent the unit from being damaged
when it is started immediately after being:
 Plugged in
 Stopped
The air conditioner will start up after 3 minutes.
2
To select the AUTO mode, press the button until Auto is
displayed on the remote controller.
Result:  The air conditioner will operate in auto mode.
 The auto fan speed will be selected
automatically in auto mode.
You cannot control the fan speed.
3
To adjust the temperature, press the buttons.
The temperature can be set between 18°C(65°F) and
30°C(86°F).
Result: The temperature will be adjusted by 1°C(1°F)
when the buttons are pressed.
4 To adjust the air swing direction, refer to page 13.
Note Fan speed in auto mode
When the room temperature is high, cool and strong
air will come out. After the room is cooled, mild air will
come out.
Selecting the Automatic Operating Mode
MWR-WH02_IB_E_33323-1.indd 6 2011-01-10 오후 1:13:30

E-7
ENGLISH
Selecting the Cooling Mode
Select the cooling mode to lower the room temperature.
1
Press the (ON/OFF) button to turn on the indoor unit.
- Do not press the (ON/OFF) button if the remote
controller is on.
Result: The air conditioner will be turned on with the
most recently used mode.
The air conditioner has a built-in protection
mechanism to prevent the unit from being damaged
when it is started immediately after being:
 Plugged in
 Stopped
The air conditioner will start up after 3 minutes.
2
To select the COOL mode, press the button until Cool is
displayed on the remote controller.
Result: The air conditioner will operate in cooling mode.
3
To adjust the temperature, press the buttons.
The temperature can be set between 18°C(65°F) and
30°C(86°F).
Result: The temperature will be adjusted by 1°C(1°F)
when the buttons are pressed.
4 Select the fan speed by pressing the button.
Result: Each time the button is pressed, fan speed will
change in the following order:
Low  Med  High  Auto
5 To adjust the air swing direction, refer to page 13.
Note If you select heating mode while the cooling mode is in
operation, cooling mode will be canceled.
MWR-WH02_IB_E_33323-1.indd 7 2011-01-10 오후 1:13:32

E-8
Select the dry mode if the room is too humid.
Using this mode will slightly lower the room temperature.
1
Press the (ON/OFF) button to turn on the indoor unit.
- Do not press the (ON/OFF) button if the remote
controller is on.
Result: The air conditioner will be turned on with the
most recently used mode.
The air conditioner has a built-in protection
mechanism to prevent the unit from being damaged
when it is started immediately after being:
 Plugged in
 Stopped
The air conditioner will start up after 3 minutes.
2
To select the DRY mode, press the button until Dry is
displayed on the remote controller.
Result:  The air conditioner will operate in dry mode.
 The Auto fan speed will be selected
automatically in the dry mode.
You cannot control the fan speed.
3
To adjust the temperature, press the buttons.
The temperature can be set between 18°C(65°F) and
30°C(86°F).
Result: The temperature will be adjusted by 1°C(1°F)
when the buttons are pressed.
4 To adjust the air swing direction, refer to page 13.
Note If the indoor unit does not support Dry mode,
Dry is not displayed on remote controller.
Selecting the Dry Mode
MWR-WH02_IB_E_33323-1.indd 8 2011-01-10 오후 1:13:34

E-9
ENGLISH
Selecting the Fan Mode
Select the fan mode to circulate air without changing the
temperature.
1
Press the (ON/OFF) button to turn on the indoor unit.
- Do not press the (ON/OFF) button if the remote
controller is on.
Result: The air conditioner will be turned on with the
most recently used mode.
The air conditioner has a built-in protection
mechanism to prevent the unit from being damaged
when it is started immediately after being:
 Plugged in
 Stopped
The air conditioner will start up after 3 minutes.
2
To select the FAN mode, press the button until Fan is
displayed on the remote controller.
Result:  The air conditioner will operate in fan mode.
 You cannot adjust the temperature in fan
mode.
3
Select the fan speed by pressing the button.
Result: Each time the button is pressed, fan speed will
change in the following order:
Low  Med  High
4 To adjust the air swing direction, refer to page 13.
Note If the indoor unit does not support Fan mode,
and you have pressed the button, the lamp
will be displayed.
MWR-WH02_IB_E_33323-1.indd 9 2011-01-10 오후 1:13:35

E-10
Select the heat mode to raise the room temperature.
1
Press the (ON/OFF) button to turn on the indoor unit.
- Do not press the (ON/OFF) button if the remote
controller is on.
Result: The air conditioner will be turned on with the
most recently used mode.
The air conditioner has a built-in protection
mechanism to prevent the unit from being damaged
when it is started immediately after being:
 Plugged in
 Stopped
The air conditioner will start up after 3 minutes.
2
To select the HEAT mode, press the button until Heat is
displayed on the remote controller.
Result: The air conditioner will operate in heating mode.
3
To adjust the temperature, press the buttons.
The temperature can be set between 16°C(61°F) and
30°C(86°F).
Result:  The temperature will be adjusted by 1°C(1°F)
when the buttons are pressed.
 The air conditioner will start heating if the
set temperature is higher than the room
temperature.
 The fan will operate even if the set
temperature is lower than the room
temperature.
4 Select the fan speed by pressing the button.
Result: Each time the button is pressed, fan speed
will change in the following order:
Low  Med  High  Auto
5 To adjust the air swing direction, refer to page 13.
Note  After starting heating operation, the air may not come out
immediately to prevent the cold air from coming out.
 (Defrost indicator)
- Defrost indicator will be on while your outdoor unit
defrosts the frost formed during heating operation.
After defrosting is completed, the indicator will be off.
(Air will not come out of the indoor unit while defrosting.)
 If you stop running the air conditioner after heating
operation, the air will come out for a while to radiate heat.
 If you select cooling mode while the heating mode is in
operation, heating mode will be canceled.
Selecting the Heating Mode
The heating mode can be selected only on the heat pump models.
MWR-WH02_IB_E_33323-1.indd 10 2011-01-10 오후 1:13:38

E-11
ENGLISH
Selecting the Quiet Mode
Select the quiet mode to run the indoor unit as quietly as
possible.
1
Press the (ON/OFF) button to turn on the indoor unit.
- Do not press the (ON/OFF) button if the remote
controller is on.
Result: The air conditioner will be turned on with the
most recently used mode.
2
Select the desired operation mode by pressing the
button.
3
Press the button to select the Quiet mode.
Result:  The air conditioner will operate in quiet mode.
 Operating noise will be reduced.
Note Press the button again to exit the quiet
mode.
Note  If the indoor unit does not support Quiet mode,
will be displayed when you press the
button.
 If you press the button in fan mode,
will be displayed.
MWR-WH02_IB_E_33323-1.indd 11 2011-01-10 오후 1:13:39

E-12
Selecting the Sleep Mode
Select the sleep mode to sleep in comfort without worrying to
turn off the air conditioner in the middle of the night.
The air conditioner will turn off automatically after 6 hours.
1
Press the (ON/OFF) button to turn on the indoor unit.
- Do not press the (ON/OFF) button if the remote
controller is on.
Result: The air conditioner will be turned on with the
most recently used mode.
2
Select the desired operation mode by pressing the
button.
Note Only cooling and heating mode support the sleep
mode.
3 Press the button to select the Sleep mode.
Result:  The air conditioner will operate in sleep mode.
 The air conditioner will gradually raise or
lower the set temperature internally and
eventually turn off automatically after 6 hours.
Note Press the button again to exit the sleep mode.
Note  If the indoor unit does not support Sleep mode,
will be displayed when you press the
button.
 If the indoor unit is not in Cool/Heat mode,
will be displayed when you press the button.
MWR-WH02_IB_E_33323-1.indd 12 2011-01-10 오후 1:13:40

E-13
ENGLISH
Adjusting the Air Swing Direction
Adjust the air swing direction to circulate the air according
to various needs. By adjusting the air swing direction, the
efficiency of the air conditioner can be increased.
1
Press the button.
Result:  The blade will start swinging up and down.
 Press the button again to stop the
blade from swinging and set the blade to the
desired position.
Note The air swing direction cannot be set on duct type
indoor units.
will be displayed when the button is
pressed.
MWR-WH02_IB_E_33323-1.indd 13 2011-01-10 오후 1:13:41

E-14
Checking the Room Temperature
You can check the current room temperature.
1
Press the button to check the room temperature.
Result: The room temperature will be displayed for
3 seconds and return to set temperature display.
Note The room temperature may be slightly different
depending on the installation location of the
remote controller.
Locking the Wired remote controller
Lock the wired remote controller to prevent it from children and
changing the settings unwillingly.
1
Press the button for 3 seconds.
Result:  will be displayed and the wired remote
controller is locked.
 When the wired remote controller is locked,
you cannot control the air conditioner by the
wired remote controller.
Note Press the button for 3 seconds again to cancel
the lock.
MWR-WH02_IB_E_33323-1.indd 14 2011-01-10 오후 1:13:42

E-15
ENGLISH
Setting the On Timer
You can set the indoor unit, which is connected to the wired
remote controller, to turn on at the pre-set time.
1
Press the button to set the On Timer.
Result:  Default time (0.5 hour) will be displayed
and the ‘On’ indicator will blink.
 If the On Timer is already set, current time will
be displayed and ‘On’ indicator will blink.
2
Press the button until you set your desired time.
Result: You can set the time between 0.5~24 hours.
Note 0.5~3 hours : Time will be changed in 0.5 hour
unit each time you press the
button.
3~24 hours : Time will be changed in 1 hour
unit each time you press the
button.
3
Press button to set the time.
Result:  ‘On’ indicator will stop blink.
 When the pre-set time passes, indoor unit will
turn on automatically.
 Operation mode, temperature, fan speed, air
flow direction will be same as the most recent
operation settings.
Note  When the On Timer is set, you can cancel it by
pressing the button.
 When the centralized control is set, Timer will not be
effective.
 Timer will be canceled if you press either or
button while the Timer is already set.
 Timer will be canceled if you reset the wired remote
controller.
 You can set one On Timer and Off Timer each.
 Timer will be canceled if you turn on the wired remote
controller with button while the Timer is set.
MWR-WH02_IB_E_33323-1.indd 15 2011-01-10 오후 1:13:43

E-16
Setting the Off Timer
You can set the indoor unit, which is connected to the wired
remote controller, to turn off at the pre-set time.
1
Press the button to set the Off Timer.
Result:  Default time (0.5 hour) will be displayed and
the ‘Off’ indicator will blink.
 If the Off Timer is already set, current time will
be displayed and the ‘Off’ indicator will blink.
2
Press the button until you set your desired time.
Result: You can set the time between 0.5~24 hours.
Note 0.5~3 hours : Time will be changed in 0.5 hour
unit each time you press the
button.
3~24 hours : Time will be changed in 1 hour
unit each time you press the
button.
3
Press button to set the time.
Result:  ‘Off’ indicator will stop blink.
 When the pre-set time passes, indoor unit will
turn off automatically.
Note  When the Off Timer is set, you can cancel it by
pressing the button.
 When the centralized control is set, Timer will not be
effective.
 Timer will be canceled if you press either or
button while the Timer is already set.
 Timer will be canceled if you reset the wired remote
controller.
 You can set one On Timer and Off Timer each.
 Timer will be canceled if you turn off the wired remote
controller with button while the Timer is set.
MWR-WH02_IB_E_33323-1.indd 16 2011-01-10 오후 1:13:44

E-17
ENGLISH
Setting the Auto Stop Function
The wired remote controller can be set to turn off the indoor
unit(s) after a set period of time has passed since any button on
the remote controller was last pressed. This function is used to
turn off the indoor unit in case the user forgets to turn off the
indoor unit.
1
Press the button for 3 seconds to enter the setup
mode.
Result:  The wired remote controller will enter the
setup mode and the menu will display .
 Press the button to enter the Auto Stop
setup mode.
2
Press the buttons to set the auto stop time.
Result:  Time is adjusted by 1 hour when the
buttons are pressed.
 The default time setting is 0. The auto stop
time can be set between 0 and 12 hours.
 If you select 0, auto stop function will be
canceled.
3
Press the button to complete the auto stop function.
Result: Auto stop function is set.
Note To cancel the auto stop function, press the
button.
4
Press the button.
Result:  Menu selection display will end.
 will be displayed.
Note  The time-counting of Auto Stop function is clear
after pressing the , , , , ,
, buttons.
 Auto Stop function doesn’t work under the
centralized control.
MWR-WH02_IB_E_33323-1.indd 17 2011-01-10 오후 1:13:46

E-18
Setting the Temperature Limits
You can set upper limit/lower limit temperature so that the
desired temperature is not set too high or low.
1
Press the button for 3 seconds to enter the setup
mode.
Result: The wired remote controller will enter the setup
mode and the menu will
display .
2
Press the buttons and select menu .
Result:  Each time the buttons are pressed,
menu number increases by 1.
 Press the button to enter the
temperature limit setup mode.
3
Set the lower and upper temperature limit by pressing the
buttons.
Note  Set the lower limit first by pressing the
buttons followed by the
button and set the upper limit.
 Each time the buttons are pressed,
the temperature is increased/decreased
by 1°C(1°F) .
 Press the button after setting.
 Press the button to cancel the
temperature limits setup.
4
Press the button to complete the temperature limit
settings.
Result: The temperature setting will be restricted
by the set lower/upper temperature limit.
Note Press the button to cancel the setting.
5
Press the button.
Result: Menu selection display will end.
Note  The lower limit can not be same or higher than upper
limit.
 Even though you set the lower temperature limit to
16°C(61°F), lower temperature will be set to 18°C(65°F) in
all the modes except in heating mode. When you set the
lower temperature limit to 18°C(65°F), it will be applied
under all the operation modes.
MWR-WH02_IB_E_33323-1.indd 18 2011-01-10 오후 1:13:48

E-19
ENGLISH
Locking the Part of the Wired remote controller
To prevent the wired remote controller from children and
changing settings unwillingly, you can lock some functions of
wired remote controller.
1
Press the button for 3 seconds to enter the setup
mode.
Result: The wired remote controller will enter the setup
mode and the menu will
display .
2
Press the buttons and select menu .
Result:  Each time the buttons are pressed,
menu number increases by 1.
 Press the button to enter the lock setup
mode.
Note Press the button to cancel the setting.
3
Using the buttons, you can set the lock setting
value of the , , , buttons.
Result:  Lock setting value
- 0: Cancel lock
- 1: Set lock
 Press the button after setting.
4
Press the button to complete the part lock settings.
Result:  Changed settings will be applied.
 will be displayed when the lock function is
set.
Note Press the button to cancel the setting.
5
Press the button.
Result: Menu selection display will end.
Note  If the centralized control is set, you cannot use the
part lock function.
 You cannot use the part lock function when Lock all
is set.
 Part Lock function can be applied to , ,
, and buttons only.
On/off
button
Temperature
setting button
Mode button
Fan speed button
MWR-WH02_IB_E_33323-1.indd 19 2011-01-10 오후 1:13:50

Air Conditioner
user manual
MWR-WH02_IB_E_33323-1.indd 20 2011-01-10 오후 1:13:51