S&P DOMEO 210 RD User manual

DOMEO 210 RD
DOMEO 210 RD SC
EN

3
 General information
 Technical information
 Installation
 Characteristics and electrical connections
 Commissioning the DOMEO
 Operating the DOMEO
 Maintenance
 3XWWLQJRXWRIVHUYLFHDQGUHF\FOLQJ
CONTENTS
The following items are included :
1. 1 x DOMEO 210 RD
2. 1 x remote control
3. 1 x console programming (Excepting Domeo 210 RD SC model)
4. 1 x wall bracket
5. 2 x drain ducts
6. 1 x drain connection for air-conditioned houses
7. 1 x cable gland M16
8. 1 x 3 connections tab
9. 1 x Instruction manual

4
1. GENERAL INFORMATION
1.1 - Introduction
This manual is intended for the use of the central balanced-flow high efficiency DOMEO and its
peripherals (ductwork, vents, controllers).
It is designed to provide clear and safe guidance for the design, installation and use of the
product.
The products are constantly evolving and so, Soler & Palau reserves the right to modify this
manual without prior notice.
1.2.- Warranty and Liability
Warranty
The DOMEO heat recovery system has three years warranty from the date of purchase. This
warranty includes free delivery of necessary spare parts.
The warranty does not cover:
Installation and removal costs
Defects that, in the opinion of Soler & Palau, are due to improper installation, handling, neglect or
accidental damage.
Those defects that arise as a result from operations or repair performed by a third party without
permission from Soler & Palau.
To return a defective part, the user should contact their installer.
Liability
DOMEO is designed for ventilation systems in individual dwellings.
Soler & Palau is not responsible for damage caused by:
•Improper use,
•Normal wear of components,
•Failure to follow the instructions in this manual concerning safety, use and installation.
•The use of parts not supplied by Soler & Palau.
1.3.- Safety
General health and safety standards
The heat exchanger DOMEO has been designed to be incorporated into a ventilation system.
Following installation, there should be no risk to safety, health and the environment according to
EC directives. This also applies to other products used in the installation.
The following general guidelines are important:
Follow the safety instructions to prevent injuries and damage to the motorised fans.
The technical characteristics described in this manual may not be changed.
The motorised fans must not be modified.
The motorised fans must be supplied with a single phase AC supply of 230 V / 50 Hz.
So that the installation complies with EC directives, the DOMEO must be connected to the
electricity grid according to current national standards.
The device must be installed so that under normal operating conditions, there is no risk of contact
with moving parts and power.
The DOMEO meets legal requirements for electrical equipment.
Before working on the machine, always turn the power off.
Use appropriate tools.
Use the machine only for the purpose for which it is intended.

5
D 125mm
Type A
connection
(Factory configuration)
Type B
connection
With the DOMEO you have the possibility to choice the connecting
ductwork side.
2. TECHNICAL INFORMATION
2.1.- General information
The DOMEO ensures optimum ventilation of a house with a maximum energy recovery. It draws air
from the rooms (bathroom(s), toilet, kitchen and wash room(s)) and supplies fresh air through the
main rooms (living room, bedroom (s), office, etc. )
The fresh and extract airflows are separated and filtered. Only heat energy is transferred to the
fresh filtered air that is introduced. Due to the high-efficiency heat exchanger used in the DOMEO
performance can reach 92%.
Condensation forms during the heat exchange process and is recovered in the condensate tray,
which must be connected to a waste water drain.
The DOMEO is equipped with a double condensate drain system that allows use in winter and
summer for heated homes.
The DOMEO has a 100% heat exchanger bypass system and this allows the introduction of fresh
air at night without it being heated by contact with warm air accumulated in the house during the
day. The system operates automatically or can be used manually (see section 5-2).
2.2.- Description
Fresh air
inlet
Fresh air
supply
Extraction
of stale
air
Discharge
to the
outside
Fresh air
inlet Extraction
of stale
air
Discharge
to the
outside
Access to
filters
Fresh air
supply

6
Fresh air inlet:
This spigot is to connect the supply duct of fresh air from outside.
Install the fresh air intake (wall or roof) a sufficient distance from any area of
high pollution (trees, exhaust fumes, road, etc).
This duct must be sealed and insulated to prevent condensation on
the outside and inside.
Fresh air supply:
Connect the supply air duct from living room and bedrooms
To avoid thermal losses, it is recommended to use insulated ducts for the warm
air.
Extract air:
Connect the extract duct from the toilets, bathrooms and the kitchen.
To avoid thermal losses and optimise the performance of the installation, it is
recommended to use insulated ducts for the warm air.
By-pass:
Having avoided the heat exchanger, the 100% by-pass system of the IDEO
allows the introduction of cooler fresh air in the night without it being warmed
by the warm air accumulated into the house during the day.
Discharge of extract air:
Connect the discharge duct to the outside.
This duct must be well sealed and thermally insulated to avoid
condensation both on the inside and outside.
Operation with
the bypass deactivated
Operation with
the bypass activated

7
2.3 - Dimensional characteristics
2.3.a - Central:
Weight: 15Kg:
2.3.b –Remote Control
3 - INSTALLATION
Depending on the ductwork configuration, you have the possibility to modify the connecting side, Type A
(Connection of the condensation drain on the right) or Type B (Connection of the condensation drain on
the left). In case of Type B, you must invert the filters.
Extraction
Filter G4
Fresh air
Filter F5
Fresh air
Filter F5
Extraction
Filter G4
Type A connection
(Factory configuration) Type B connection

8
Uninsulated
duct
Insulated
duct
Insulated
duct
Ducts must be insulated and correctly
installed.
The Domeo can be installed far away of the bedrooms and inside a room with
acoustic treatment (technical room, cupboard, ...).
It is advisable to install the DOMEO in the heated area of the house. If not, it is
mandatory to isolate the condensation drain.
Wall bracket
In areas where temperatures are regularly negative or can drop below -10ºC, it is
advisable to install a preheating battery.
•Air-conditioned house
In summer, in this configuration, the condensation is generated on the other side of the heat
exchanger. So, DOMEO is equipped with a dual condensate drain system.

9
SAMPLE ”REPARTITION” ASSEMBLY
Air intake
PAF 125
kitchen
Toilets
Living room
&
(*) Bedrooms
Or
CPR or CT
125
BDO or BOAP
125
BDO or TPM 80
If using insulated
flexible ducting it is
imperative to fully
stretch it.
Or
Air intake
PAQS125
BDO or TPM 80
RD 80*
RD 80
PLENUM UNI EX
5P/125
PLENUM UNI 6P/125
,IWKHXQLWLVFRQQHFWHG
WRD&DQDGLDQZHOOLV
PDQGDWRU\WRFDOFXODWH
WKHSUHVVXUHORVVRI
WKHLQVWDOODWLRQ

10
Kitchen
Bathrooms
CPR or CT
125
BDO or BOAP
125
BDO or TPM
80 +
RD80
BDO 80
+
RD80*
+
+
Air intake
PAF 125
Or
Or
Air intake
PAQS125
SAMPLE “DISTRIBUTION” ASSEMBLY
Living Room
&
(*) Bedrooms
If using insulated
flexible ducting it is
imperative to fully
stretch it.
,IWKHXQLWLVFRQQHFWHG
WRD&DQDGLDQZHOOLV
PDQGDWRU\WRFDOFXODWH
WKHSUHVVXUHORVVRI
WKHLQVWDOODWLRQ

11
3 5 6
2
1 4
4 - CHARACTERISTICS AND ELECTRICAL CONNECTIONS
Connect the supplied cable to the mains using a sealed connection box.
Power:
Single phase 230V-50Hz
Max. current:
0,8 A
Electrical protection:
2 A (curve D) or 3 A
Maximum Power:
120 W
Maximum ambient temperature:
50ºC
Maximum flow temperature:
45ºC
Connection
box
Electrical panel
In areas where temperatures are regularly negative or can drop below -10ºC, it is advisable to
install a preheating battery.
Power wire
type H05VV-F-3G0,75
Electrical panelConnection box
•MODBUS network
Use shielded cable and twisted-pair typePAR-POS 2x2x0,34.
•Free voltage contact connection
Pass the cable through the interior of ferrite type WE 742 727 33 MnZn twice.
•
Installation of cable glands

12
  
+!#
.-
 

  !
 !
!#!+
)+*
&(
! "!
 ! # 
!
"!
 !
# 
"!
%!! 
"!
"& 
$ "&
!
%!! 
$ "&
!
"& 

$ "&
!
"!
 !
# 
%!
 
-(.-+
/0
/2.
02 -
12
'
!
(! 
 !(!
!! +
.-

!

13
5–MANAGING OF THE DOMEO
5.1 –During the installation:
The programming console allows adjust the commissioning settings and see the different parameters of
the installation.
For Domeo 210 RD SC model the console must be purchased as an accessory.
Down key
Display Up key
Validation
key
MENU OPTIONS VALUES FACTORY SETTING
Language English, Francais, Español, Deutsch, Italiano, Nederlands English
synchronisation mode Remote control 1, 2,3,4 1
Volt free contact NO/NC NO
Preheating battery Yes/No No
Post-heating battery Yes/No No
Air Interior Quality sensor (AIQ)) Yes/No No
Connection type A / B A
Airflow units
m
3
/h / l/s m
3
/h
Unbalancing Airflow -15%,…+15% 0
Airflow setting:
- Low Airflow
60,…210 m
3
/h 60 m
3
/h
- High/Boost Airflow 30 minutes
60,…210 m
3
/h 120 m
3
/h
- Free cooling 8H
60,…210 m
3
/h 210 m
3
/h
AIQ sensor setting parameters
Value QMini 0-10V
60,…210 m
3
/h 60 m
3
/h
Value QMaxi 0-10V
60,…210 m
3
/h 120 m
3
/h
Value VMini 0-10V 0-10V 0
Value VMaxi 0-10V 0-10V 10
Automatic Bypass On/Off ON
Tºext conditon > Auto Bypass 11,…20ºC + 12ºC
Tªint condition > Auto Bypass 21,…30ºC + 24ºC
Manual Bypass timer 1,…24 Hours 8 H
Defrost type Intake air diminution / Stop
Preheating battery :
- Temperature ON -15,…5ºC 0ºC
- Temperature OFF -5,…10ºC +5ºC
- Constante temperature +1,…10ºC +4ºC
Post-heating battery:
Constante comfort temperature 12,…30ºC + 18ºC
Factory parameters reset Yes/No No
Couverture Radio 0,25,50,75,100%
Current airflow 60,…210
Defrost mode On, Off
Batteries Préheating: On/Off - Post-heating: On, Off
Sofware version V0.0
Extract motor Error, Ok
Supply motor Error, Ok
Bypass Error, Ok
Communication Error, Ok
Sensors Error, Ok Tº Extract, Discharge, Fresh air, Supply
Tª Extract
Tº Discharge
Tª Fresh Air
Tº Supply
Installation test Very good, Good, Acceptable, Bad Off
SET UP
INSTALLATION
READING
PARAMETERS

14
5.1.a - Adjust setting:
1. To connect the programming console, unscrew the both screws located on the lower part of the
DOMEO, remove the filters cover and then the front cover.
2. Connect the programming console with RJ45 plug located on the right of the electronic board.
3. Setting of the installation parameters.
1
2
1
2
3
Code : 33
Enter the code with the key and confirm with the key , then move to the
next step with the key .
Choice of the language:
Enter with the key .
Move with the keys and confirm the language with the key and move to the next
step with the key .
6\QFKURQL]DWLRQ:
7KH'20(2FRXOGEHSLORWHGE\DPD[LPXPRIUHPRWHFRQWUROV)RU
RQO\UHPRWHFRQWURODOZD\VXVHWKHQ
7RELQGHDFKUHPRWHFRQWUROIROORZWKHQH[W
2QWKHUHPRWHFRQWUROSXVKRQWKHERWKNH\VDVLQGLFDWHGLQWKH
DWWDFKHGLPDJH
7KHQLQWKHFRQWUROSDQHOSODFHRQWKHVFUHHQ´UHPRWHFRQWUROµZLWKWKHNH\VDQG
SXVKWKHNH\7KH´UHPRWHFRQWUROµZLOOEHGHOHWHGLWZLOOVWDUWIODVKLQJDQGZLOO
EHJLQWKHERQGLQJSURFHVV7KHQWKHFRGHRIWKHUHPRWHFRQWUROZLOODSSHDUZKHQWKH
UHPRWHFRQWURODQGWKH'20(2DUHERXQG)RUWKHRWKHUUHPRWHFRQWUROVHWUHSHDW
WKHDFWLRQE\DVVLJQLQJDVSHFLILFQXPEHUZLWKWKHNH\V
(QWHUZLWKWKHNH\DQGPRYHWRWKHGLIIHUHQWRSWLRQVZLWKWKHNH\V

15
Unbalance of the airflow:
This setting could be necessary in case of:
1–Case of an open chimney:
In this case, it’s necessary to make an airflow aportation equivalent at the stack effect airflow.
In this case there are two possibilities:
a. Make a specific air inlet. In this case ensure that it’s sealable.
b. Add an additional intake airflow using the DOMEO corresponding at the stack effect
airflow.
Follow these recommendations:
. Watch that all doors, windows, … are securely closed,
. Light the chimney fire,
. Adjust the unbalance airflow up to reach the good chimney performance
2. Case of unbalance between the intake and extract airflows:
It could be possible when one of the both ductworks is advantaged or disadvantaged.
Enter with the key and modify the unbalance value with the keys , then confirm with
the key .
This setting is done by the intake airflow compared to the extract airflow.
Volt free contact:
The electronic board is equipped with a volt free contact that allows increase to the boost airflow
controlled by an external sensor (switch, CO2 sensor, PIR sensor, humidity sensor, …). You
can change the position of the contact:
NO = Normally Open
NC = Normally Closed
Enter with the key and move to the different options with the keys .
Then confirm with the key .
Pre-heating battery:
In case of a connected pre-heating battery. Enter with the key , modify the option with the
keys .
Then confirm with the key .
Post-heating battery:
In case of a connected post-heating battery. Enter with the key , modify the option with the
keys .
Then confirm with the key .
Air quality sensor (0-10V):
In case of a connected sensor (CO2, VOC, RH, …). Enter with the key , modify the option
with the keys .
Then confirm with the key .
Connection Type:
Adjust A or B depending on the connection Type
Enter with the key , modify the option with the keys .
Then confirm with the key .
Units:
You can choose the airflow unit in m3/hour or litres/second.
Enter with the key and choose the unit with the keys , then confirm with the key .

16
Boost/High airflow:
Setting of the high/boost ½ hour temporized airflow.
Enter with the key choose the airflow value with the keys , then confirm with the
key .
Low airflow air quality sensor*:
Setting of the minimum airflow.
Enter with the key choose the airflow value with
the keys ,
then confirm with the key .
Free cooling airflow:
Having avoided the heat exchanger, the 100% by-pass system of the IDEO allows the
introduction of cooler fresh air in the night without it being warmed by the warm air
accumulated in the house during the day.
This system works automatically with this conditions:
- Tº inner >1+ Tº outer and Tº inner > 24ºC and Tº outer> 12ºC,
The specific airflow can be adjusted to optimize the cooling nigh time or free cooling (see
paragraph 5-1-a)
If you want , you can manually switch on the by-pass mode for a period of 8 hours, by
pressing the by-pass button. During this operation it is possible to cancel this function by
pressing the by-pass key once more.
Enter with the key choose the airflow value with the keys , then confirm with the
key .
High airflow air quality sensor*:
Setting of the maximum airflow.
Enter with the key choose the airflow value with
the keys ,
then confirm with the key .
Minimum voltage of the air quality sensor*:
Setting of the minimum voltage.
Enter with the key choose the voltage value with
the keys ,
then confirm with the key .
Maximum voltage of the air quality sensor*:
Setting of the maximum voltage.
Enter with the key choose the voltage value
with the keys ,
then confirm with the key .
Qmin.
Qmax.
Umin. Umax.
Airflow (m3/h)
Tension (v)
Working chart of the
Air Quality sensor (0-10V)*
*: Humidity, CO2, VOC sensor.
Automatic By-pass:
You can activate or deactivate the automatic function for the by-pass.
Enter with the key , choose activate (ON) or deactivate (OFF) with the keys ,
then confirm with the key .
If it is deactivated, you can always switch on the bypass with the remote control.
Text Automatic By-pass:
You can modify the outdoor bypass activation temperature.
Factory setting: +12ºC
Setting range: +11 –+20ºC
Enter with the key , modify the temperature with the keys ,
then confirm with the key .
Low airflow:
Setting of the low airflow/low speed.
Enter with the key choose the airflow value with the keys , then confirm with the
key .

17
Constant temperature of the post-heating battery:
Allows adjust the constant temperature downstream the post-heating battery.
Factory setting: +18ºC
Setting range: +12ºC –+30ºC
Enter with the key and choose the temperature with the keys , then confirm with the
key .
Shutdown of the preheating temperature:
Allows adjust the shutdown temperature of the preheating temperature.
Factory setting: +5ºC
Setting range: -5ºC –+10ºC
Enter with the key and choose the temperature with the keys , then confirm with the
key .
Type of defrost:
You can choose two types of defrost control:
1–By reduction of the intake airflow (very tight home or temperate climate)
2–By shutdown of the intake airflow (not very tight home or cold climate)
Enter with the key and choose the type of defrost with the keys , then confirm with the
key .
Start-up of the preheating temperature:
Allows adjust the start-up temperature of the preheating temperature.
Factory setting: 0ºC
Setting range: -15ºC –+5ºC
Enter with the key and choose the temperature with the keys , then confirm with the
key .
Constant temperature of the preheating battery:
Allows adjust the constant temperature downstream the preheating battery.
Factory setting:= +4ºC
Setting range: +1ºC –+10ºC
Enter with the key and choose the temperature with the keys , then confirm with the
key .
Factory parameters reset:
Allows to reset the DOMEO.
Enter with the key and choose YES or NO with the keys , then confirm with
the key .
Tint automatic bypass:
You can modify the internal bypass activation temperature.
Factory setting: +24ºC
Setting range: +21 –+30ºC
Enter with the key , modify the temperature value with the keys , then confirm with the
key .
Manual bypass delay:
You can modify the bypass delay when is manually activated.
Factory setting: 8H
Setting range : 1 –24H
Enter with the key , modify the delay with the keys , then confirm with the key .

18
4. View of the operating states.
View of the operating states:
Allows viewing the operating DOMEO states.
Enter with the keys .
To move, use the keys .
Coverage radio signal:
Allows viewing the radio range of all remote controls appeared with DOMEO.
Push on one key of the remote controls.
1–000% 2 –000%
3–000% 4 –000%
Value > 50 % : Good coverage
Value < 50% : Possible communication troubles
Current airflow:
Allows viewing the working airflow.
Defrost:
Allows viewing if the Domeo is in defrost mode.
ON = Defrost in operation
OFF = Defrost stopped
Battery status:
Allows viewing if the preheating (PRE) and post-heating (POST) batteries are running.
PRE OFF = Stopped PRE ON = Working
POST OFF = Stopped POST ON = Working
Software version :
Allows viewing the installed software version.
Extract fan motor:
Allows viewing operating extract fan motor state.
OK : Working
ERROR : Dysfunction
Bypass:
Allows viewing the operating bypass state.
CLOSED : On hold
OPEN : Working
Temperature sensors:
Allows viewing the operating temperature sensors state (OK or ERROR).
T11 : Extract sensor
T12 : Discharge sensor
T21 : Fresh air sensor
T22 : Supply air sensor
Intake fan motor:
Allows viewing operating intake fan motor state.
OK : Working
ERROR : Dysfunction

19
Extract temperature sensor:
Allows viewing the temperature on the extract ductwork upstream of the core.
Temperature range: -30ºC –+50ºC
Installation test :
Allows testing the pressure loss of the installation.
Enter with the key and modify the value « OFF » to « ON » with the key , then
confirm with the key , « TESTING » appears and after few seconds the installation level
appears :
•Very good
•Good
•Acceptable
•Bad
Discharge temperature sensor:
Allows viewing the temperature on the discharge ductwork downstream of the core .
Temperature range: -30ºC –+50ºC
Fresh Air temperature sensor:
Allows viewing the temperature on the fresh air ductwork downstream of the core .
Temperature range: -30ºC –+50ºC
Supply air temperature sensor:
Allows viewing the temperature on the supply air ductwork downstream of the core .
Temperature range: -30ºC –+50ºC

20
Holidays mode: (Flashing red LED)
Press the left key for 3 seconds to activate Holidays mode (50% of minimum airflow). It is
possible to return to normal mode by pressing the same key once more.
Filters alarm: (red LED):
DOMEO alerts when the filter timer has arrived to the limit lightning a red LED on the
right hand key. The factory setting is 9 months after commissioning or changing the
filters. You must change the filters.
If the 9 month interval is not ideal for the configuration or use of your installation (filters
too dirty or clean) it is possible to adjust this setting from 6 to 15 months (in 3 monthly
steps –see paragraph 5-1-b)
Once changes have been made push the button 3 seconds to deactivate the
alarm and reset the timer.
Minimum airflow (Trickle): (Flashing green LED)
When the DOMEO is in Boost mode, it is possible, by pressing the left button,
to return to the minimum airflow before ½ hour has elapsed
Boost: (Flashing green LED)
A button that enables the boost airflow for 30 minutes to be selected in ½-hour steps.
By-pass: (Flashing green LED)
On having avoided the heat exchanger, the 100% by-pass system of the
DOMEO allows the introduction of fresh air in the night without being warmed
by the warm air accumulated in the house during the day.
This system works automatically with this conditions:
- Tº inner >1+ Tº outer and Tº inner > 24ºC and Tº outer> 12ºC,
The specific airflow can be adjusted to optimize the cooling nigh time or free cooling (see
paragraph 5.1.a 3)
If you want , you can manually switch to by-pass mode by pressing the by-pass button.
During this operation it is possible to cancel this function by pressing the by-pass key
once more.
The remote control put on the “energy saving” mode after 10 seconds, switching off all LEDS.
Pushing on one of the keys the function LED activated lights.
5.2 - During use
The remote control allows the user to:
•Activate the boost for ½ hour.
•Return manually to the minimum airflow
•Put DOMEO in holidays mode
•Manually switch on the by-pass mode
•Reset filters alarm
Kitchen Boost
By-pass
Low Airflow
+
Holidays mode