Sanipex BAGNODESIGN BDA-CUB-UNI-GEN User manual

www.sanipexgroup.com
BDA-CUB-UNI-GEN
CUBE & UNIVERSAL HEATED TOWEL RAIL

IMPORTANT PLEASE READ
 B 
 

 






 L  C 



 x 
           
          
 








 

 







WARNING
!
1. Follow installation instructions carefully to ensure the unit is properly attached to the
w all.
2. To avoid a possible fire hazard, it is essential unit is mounted in accordance with the
g uidelines stated in the instruction.
3. Radiator is intended for indoor use only, do not place the radiator inside a shower,
ste am
room, or wherever the unit would be exposed to water.
CAUTION
IMPORTANT CHILD SAFETY NOTE
Important: Please note that you are 100% legally responsible for your own child's safety at
home. Once the radiator is installed, it can become a hazard for children as a) This radiator is
not designed to support the unreasonable extra weight, such as that of a child, and b) The
radiator becomes hot during use. Due to this, we must stress that you should not allow children
to climb/grab/play with the radiator or rails, as this can cause an accident or injury for the child,
from heat, falling, or the radiator being pulled off the wall.
TOOLS YOU MIGHT NEED
TECHNICAL DATA
It should only be filled with water, and at a temperature below100°C(212°F). See table Below
for installation requirements. If the temperature exceeds 48°C(or 120°F), please install a
warning sign near the product to avoid burning and scolding accidents.
Temperatures: 0 C C < t < 100 C
Comments: If ambient temperature below 1°C drain out the water to prevent freezing.
Important
Wipe the surface clean with a soft,damp cloth. Never use abrasive cleaners on this product as
they will damage the surface.
Adjustanble Wrench Screw Driver Electric Drill
Pencil Spirit Level Rubber Hammer
Tape Measure Clean Cloth Glove

BEFORE INSTALLATION
!
CAUTION
Observe all local plumbing and building codes.
Read these instructions carefully to ensure proper installation
Check to make sure you have the following parts indicated below.
Please check you have all of these items in the box.
Please check you have all of these items in the box.
REQUIRED PARTS
Heating element(1pcs)+ Blanking plug(1pcs)
WALL SUPPORT
X4
BRACKET BODY
X4
LONG SCREW
X4
SHORT SCREW
X4
AIRVENT
X1
BLANKING PLUG
X1
WALL PLUG
X4
WASHER
X2
LONG SCREW
X4
BODY
X1

BEFORE INSTALLATION
Turn radiator upside down and fill with a
combination of water and a rust inhibitor 90%
water5% inhibitor allow 5% air for expansion.
BOTTOM
180°
TOP
TOP
BOTTOM

BEFORE INSTALLATION
Please make sure the heating
elemaent is tightened securely.
Please note the electrical wiring
must be carried out by a
qualified electrition.

INSTALLATION PROCEDURE
1. Assembly the 4 long screws & bracket bodies to towel radiator as below image.

INSTALLATION PROCEDURE
2.Position the towel rail in desired location. Check for level and mark four equal positions for the
brackets.
Make sure the towel rail is installed vertically.
Before installation place a dust sheet on the floor to prevent losing any small parts.
!
Allow enough room for the installation of valves or thermostatic controls

INSTALLATION PROCEDURE
3.Drill holes in wall and insert wall plugs. N.B For false or studded walls different fixings can be
purchased from your local DIY store.
4.Fix all the wall supports to the wall as below image by using a screw driver

INSTALLATION PROCEDURE
3.Slide the brackets into the wall supports and tighten all the screws when in the desired
location.

INSTALLATION PROCEDURE
INSTALLATION COMPLETE

1. Operation instruction:
1.1 Switch on: Press button ,the device will begin to work:
1.2 Switch heating mode: Pushing button ,it will begin the consistant heating mode.
while pushing button, it will switch to boost TIMBER mode of 2 & 4 Hours.
1.2.1 Consistent Heating Mode: When the device switch ON, the temperature slection is
made by +/- buttons on the control unit in 5°C increments between 30°C and 70°cC for
example:
1.2.2 Timer mode: Pushing button, the device will enter 2/4H heating mode. it will
work as 2 hours as boost. Pushing button again, it will work as 4 hours as boost. The
screen will show as of . After 2/4 hours or pushing button during forced
heating process,it will go back to original mode.
1.3 Switch off:
1.3.1 press button , the device will be off
2. Protective Shutdown (Error):
Temperatures measured above 120°C or below -25°C by the thermostat, it will
switch the unit into a default mode "Er"

Note:

INA-CUB-UNI-GEN-02-23
www.sanipexgroup.com