SARAH ELLISON EARTH User manual

page 1 | 5 sarahellison.com.au
EARTH OUTDOOR ROUND DINING TABLE
ASSEMBLY INSTRUCTIONS
Thank you for purchasing the Sarah Ellison Earth Outdoor Round Dining Table.
This document lists the contents included in your delivery. Please take the time
to identify the hardware, as well as the individual components of this product.
As you unpack and prepare for assembly, place the contents on a carpeted or
padded area to protect them from damage.
CUSTOMER SERVICE
For Australian customer service contact: [email protected]
For any international customer service inquires please contact the retailer of purchase
HARDWARE
16x Allen Bolt 20mm (H-1)
5x Allen Bolt 25mm (H-2)
21x Flat Washer (H-3)
21x Spring Washer (H-4)
16x Dome Nut (H-5)
1x Cross Mounting Plate (H-6)
TOOLS REQUIRED
4mm Allen Key L (T-1)
PEOPLE REQUIRED FOR
ASSEMBLY
A minimum of three people are
required to assemble this product
ESTIMATED TIME OF ASSEMBLY
30 mins

page 2 | 5sarahellison.com.au
STEP 1
STEP 2
Pull out all four legs out of the boxes. Please note that Metal Mounting
Plates are pre-assembled to the concrete legs. Carefully check that
connections are tight. If needed, re-tighten Metal Mounting Plate with
leg using Allen Key (T-1).
Open box carefully, ensuring the blade of the knife does not come into
contact with the product. Remove packaging and lift the product up out
of box and gently place on ground.

page 3 | 5 sarahellison.com.au
With three people, lift tabletop upright and put it gently down on top of cross
mounting plate. Tabletop’s underneath surface has a recessed cross pattern
to help position tabletop so that holes are aligned with insert nuts.
STEP 3
Position all four legs upright so as to put down Cross Mounting Plate (H-6) on
top of all four pre-assembled square plates. Check holes alignment and attach
square plates to Cross Mounting Plate using Allen Bolts (H-1), Spring Washers
(H-4), Flat Washers (H-3) and Dome Nuts (H-5). Tighten with Allen Key (T-1)
and Wrench. Due to the heavy weight of the product we recommend
positioning the leg frame assembly in the final location
STEP 4
X16
H-1
T-1
H-6
H-5
H-3
H-4

page 4 | 5sarahellison.com.au
STEP 5
STEP 6
H-2
H-4
H-3
T-1
X5
Re-Position in your room by lifting the whole unit only –to avoid damage to your
table do not drag it in position, and don’t forget to recycle the packaging where
possible. If the table needs to be relocated please disassemble by reversing the
assembly steps and reassemble in new location
When all the holes are aligned, secure the Cross Mounting Plate
to the tabletop using Allen Bolts (H-2), Spring Washers (H-4) and
Flat Washers (H-3). Engage all bolts by hand first, then fully tighten
them using Allen Key (T-1).
WARNING
Once assembled, please do not move.
Disassemble before moving.

page 5 | 5 sarahellison.com.au
CARE INSTRUCTIONS
With a little care you can prolong the life of your furniture. The following information
is only intended as a general guideline. Please follow the instructions to ensure maxi-
mum longevity of your Sarah Ellison furniture.
• Dust often using a clean, soft, dry and lint-free cloth.
• When blot spills, wipe with a clean, damp cloth immediately.
• We do not recommend the use of chemical cleansers, abrasives or furniture
polish on our waxed finish.
• Hardware may loosen over time. Periodically check to make sure all connections
are tight. Re-tighten if necessary.