SARAH ELLISON LULL User manual

sarahellison.com.aupage 1 | 8
LULL QUEEN BED
ASSEMBLY INSTRUCTIONS
Thank you for purchasing the Sarah Ellison Lull Queen Bed. This document
lists the contents included in your delivery. Please take the time to identify
the hardware, as well as the individual components of this product. As you
unpack and prepare for assembly, place the contents on a carpeted or
padded area to protect them from damage.
HARDWARE
TOOLS REQUIRED
Screwdriver
Allen key (provided)
PEOPLE REQUIRED FOR
ASSEMBLY
A minimum of two people are
required to assemble this product
ESTIMATED TIME OF ASSEMBLY
2 hours
CUSTOMER SERVICE
For Australian customer service contact : [email protected]
For any international customer service inquires please contact the retailer of purchase
Part A
x36 Bolts
M8x35mm
Part B
x36 Spring
Washers
Part C
x36 Flat
Washers
Part D
x1 Allen Key
Part E
x48 Screws
M4x30mm
Part F
x4 Corner
Brackets
Part G
x3 Lock
Washer
1
2
3
5
56
7
8
6
4

sarahellison.com.au page 2 | 8
2
34
Part A
Part B
Part C
2
3
4
Part A
Part B
Part C 1
STEP 1
STEP 2
Lay the two side rails and base rail into a U shape on a clean, flat
surface. The edges with piping should be facing the ground. Using
4xPart A, 4xPart B, 4xPart C and the supplied Allen key, fix the three
rails together at the brackets by tightening the bolts by only 80%.
Attach the assembled base rail and side rails to the headboard
using 4xPart A, 4xPart B, 4xPart C and the supplied Allen key. Fix the
components together at the brackets by tightening the bolts by only
80%.
Once the four components have been joined together, tighten all bolts
to 100%.

sarahellison.com.aupage 3 | 8
2
3
4
Part B
Part C
1
Part A
7
STEP 3
STEP 4
Attach the four feet to the main bed assembly by fixing the corner
brackets through the holes in the rails and headboard. Use 4xPart A,
4xPart B, 4xPart C and the supplied Allen key per leg, and tighten the
bolts by only 80%.
Once all feet have been attached, tighten all bolts to 100%.
Fix the wooden feet to the centre support rail by twisting until tight, with
1xPart G between the rail and each foot.
Part G
Part G
Part G
5
6
6
6

sarahellison.com.au page 4 | 8
8
Part E
STEP 5
STEP 6
Attach the centre support rail to the main bed frame using 4xPart A,
4xPart B, 4xPart C and the supplied Allen key.
Unroll the bed slats onto the bed frame, stretching them from end to
end. Using 48xPart E and a screwdriver, fasten the slats to the frame
through the pre drilled pilot holes.
Part A
Part D
Part C
Part B
5
2

sarahellison.com.aupage 5 | 8
STEP 7
The assembly is now complete and product is ready for use.

sarahellison.com.au page 6 | 8
CARE INSTRUCTIONS
With a little care you can prolong the life of your furniture. The following information is
only intended as a general guideline. Please follow the instructions to ensure maximum
longevity of your Sarah Ellison furniture.
• Vacuum textiles regularly with an upholstery attachment to remove dust and dirt.
• Place textiles out of direct sunlight to help prevent fading. Dark colors and cotton
fabrics are particularly susceptible to sun.
• Have upholstered items professionally cleaned annually.
• In some cases, spot cleaning can cause a ring or fading. It is best to have the
entire piece or cushion casing cleaned by a professional upholstery cleaning
service to ensure uniform results.
• If you decide to spot clean on your own, check the standard cleaning codes to
determine the correct type of product to use.
• Blot spills immediately with a clean, dry white cloth. Always blot from the outer
edges inward to reduce the chance of a stain ring. Avoid hot water, which can set
a stain.

sarahellison.com.aupage 7 | 8
This page has intentionally been left blank.

sarahellison.com.au page 8 | 8