SARAH ELLISON YOKO User manual

sarahellison.com.aupage 1 | 4
YOKO BED
ASSEMBLY INSTRUCTIONS
Thank you for purchasing the Sarah Ellison Yoko Bed. This document lists
the contents included in your delivery. Please take the time to identify the
hardware, as well as the individual components of this product. As you
unpack and prepare for assembly, place the contents on a carpeted or
padded area to protect them from damage.
HARDWARE
2 x 20x100x50mm wooden dowel
2 x Ø10x30mm dowel
4 x 5/16x65mm bolt screws
4 x 8xØ19mm washer
4 x Ø8mm spring washer
16 x 5/16x25mm bolt screws
2 x Ø20x80mm dowel
8 x M10x100mm bolt screws
8 x 10xØ23mm washer
8 x 10 spring washer
TOOLS REQUIRED
Allen Key
Hex head key
PEOPLE REQUIRED FOR
ASSEMBLY
Four people
ESTIMATED TIME OF ASSEMBLY
1 hour
CUSTOMER SERVICE
For Australian customer service contact : [email protected]
For any international customer service inquires please contact the retailer of purchase.

sarahellison.com.au page 2 | 4
STEP 1
STEP 2
Lay both bed frame pieces face down onto a clean, flat surface (we
recommend using a towel or sheet underneath for protection). Using
the 2 x 20x100x50mm wooden dowel blocks and the 2 x Ø10x30mm
dowels, connect the frames by pushing the two halves together evenly
as shown below.
Use each of the 4 x 5/16x65mm bolts to fasten the two frame halves
together along the centre join, placing washers and spring washers
between the bolt head and the frame as shown below.

sarahellison.com.aupage 3 | 4
STEP 3
STEP 4
Align the Ball Feet and centre support leg with the corresponding
holes on the Bed Frames as shown. Fasten the Ball Feet and the centre
support leg to the bed frame using the 16 x 5/16x25mm bolt screws
and allen key.
With a second person to assist you, carefully turn the assembly over so
that it is now standing on the ball feet. Make sure to lift the assembled
frame rather than use the legs as a tipping point.
Using the 2 x Ø20x80mm wooden dowels, slot the headboard in place
on top of the base frame. Do not leave the headboard freestanding,
hold in place while completing step 5.

sarahellison.com.au page 4 | 4
STEP 5
Use each of the 8 x M10x100mm bolt screws and hex head key to fasten the
headboard to the base frame, placing washers and spring washers between the bolt
head and the frame as shown below. The assembly is now complete and product is
ready for use.
CARE INSTRUCTIONS
With a little care you can prolong the life of your furniture. The following
information is only intended as a general guideline. Please follow the
instructions to ensure maximum longevity of your Sarah Ellison furniture.
Timber is responsive to its environment, be mindful that heat and
moisture can cause movement and cracks in joints and damage
lacquer.
• Avoid exposing timber to direct heat and sunlight
• Wipe up spills immediately with a clean, dry cloth.
• Keep rough and sharp objects away from timber surfaces. Where
possible apply protective pads to the undersides of items being
displayed on rattan surfaces, including those with rubber feet or
bumpers.
• Dust timber surfaces frequently with a soft, slightly damp lint-free
cloth, and then wipe dry.
• Avoid using abrasives, harsh chemicals and aerosol-powered
cleaners
• For persistent spots, gently clean with a soft cloth and a solution of
water and mild detergent. Wipe dry.
• Avoid furniture polish as it can accumulate over time and leave a
residue
• Periodically also check and re-tighten any fasteners, we
recommend every six months.