SARAH ELLISON YOKO QUEEN BED User manual

sarahellison.com.aupage 1 | 8
YOKO QUEEN BED
ASSEMBLY INSTRUCTIONS
Thank you for purchasing the Sarah Ellison Yoko Queen Bed. This document
lists the contents included in your delivery. Please take the time to identify
the hardware, as well as the individual components of this product. As you
unpack and prepare for assembly, place the contents on a carpeted or
padded area to protect them from damage.
HARDWARE
(H-1) 3x Long Bolt screws
(H-2) 4x Medium bolt screws
(H-3) 8x Short bolt screws
(H-4) 20x Extra Short bolt screws
(H-5) 32x Spring washer
(H-6) 4x Flat washer
(H-7) 4x Headboard Hole Covers
(H-8) 16x JF Bolts Screw
TOOLS REQUIRED
(T-1) Allen Key L. 5mm
(T-2) Allen Key L. 4mm
PEOPLE REQUIRED FOR
ASSEMBLY
Four people
ESTIMATED TIME OF ASSEMBLY
2 hours
CUSTOMER SERVICE
For Australian customer service contact : [email protected]
For any international customer service inquires please contact the retailer of purchase.
METAL LEG
SUPPORT

sarahellison.com.au page 2 | 8
STEP 1
STEP 2
On a flat protected surface, lay frame A and B upside down. Align the
wooden dowels to connect the frames as shown. Secure both frames
using the medium bolt screw (H-2), spring washer (H-5) and flat washer
(H-6). Tighten all bolts by hand but do not fully tighten them at this
stage.
Align the holes on the Metal Frame with the corresponding holes on the
Bed Frame as shown. Secure the Metal Frame using short bolt screw
(H-3) and spring washer (H-5). Tighten all bolt by hand but do not fully
tighten them at this stage.

sarahellison.com.aupage 3 | 8
STEP 3
STEP 4
Align holes on Metal Leg support with the corresponding holes on the
Ball Feet as shown. Secure the Metal Leg Support using JF bolt Screws
(H-8). Repeat this step to assemble the remaining three Ball Feet.
Align holes on the Ball Feet with the corresponding holes on the Bed
Frames as shown. Secure the Ball Feet using extra short bolts screws
(H-4) and spring washer (H-5). Once all bolts have been inserted, fully
tighten all bolts using allen key (T-1).

sarahellison.com.au page 4 | 8
STEP 5
STEP 6
Align holes on the Centre Leg with the corresponding holes on the middle
of Bed Frames as show. Secure the Centre Leg using extra short bolts screws
(H-4) and spring washer (H-5).
Once all bolts have been inserted, fully tighten all bolts using allen key (T-1)
including all bolts from step 1 and 2.
Using a second person to assist you, carrefully turn the assembly upward.
Using a second person to assist you, align the holes on the Headboard with
the corresponding holes on the Frame A as shown. Secure the Headboard
using long bolt screws (H-1). Fully tighten using allen key (T-1).

sarahellison.com.aupage 5 | 8
STEP 7
IF NOT USING HEADBOARD
The assembly is now complete and product is ready for use.
If you do not plan to attach the headboard, apply the Headboard Hole
Covers (H-7) over the fixing holes on the top face of the frame.
HEADBOARD HOLE COVERS (H-7)

sarahellison.com.au page 6 | 8
CARE INSTRUCTIONS
With a little care you can prolong the life of your furniture. The following
information is only intended as a general guideline. Please follow the
instructions to ensure maximum longevity of your Sarah Ellison furniture.
Timber is responsive to its environment, be mindful that heat and
moisture can cause movement and cracks in joints and damage
lacquer.
• Avoid exposing timber to direct heat and sunlight
• Wipe up spills immediately with a clean, dry cloth.
• Keep rough and sharp objects away from timber surfaces. Where
possible apply protective pads to the undersides of items being
displayed on rattan surfaces, including those with rubber feet or
bumpers.
• Dust timber surfaces frequently with a soft, slightly damp lint-free
cloth, and then wipe dry.
• Avoid using abrasives, harsh chemicals and aerosol-powered
cleaners
• For persistent spots, gently clean with a soft cloth and a solution of
water and mild detergent. Wipe dry.
• Avoid furniture polish as it can accumulate over time and leave a
residue
• Periodically also check and re-tighten any fasteners, we
recommend every six months.

sarahellison.com.aupage 7 | 8
THIS PAGE IS INTENTIONALLY BLANK

sarahellison.com.au page 8 | 8