Saso SASO-PB10S User manual

Photoelectric Beam Detector
SASO-PB10S/PB30S/PB60S
Installation Instructions
Please note : This sensor is designed to detect intrusion and to initiate an alarm,
it is not a burglar-preventing device. Maker is not responsible for damage, ,injury
or losses caused by accident, theft, natural disasters, abuse, misuse, abnormal usage,
faulty installation or improper maintenance.
1. Description
Response time
adjustment
Terminals
Good LED Tamper
Wiring Hole
Power LED
2. Cautions on Installation
Alarm LED
Lens
Monitor jack
Vertical
Adjustment screw
View finder
Cover Transmitter Receiver Plate
Avoid strong light from sun, auto-
mobile head-lights etc. shining on
transmitter or receiver
Do not install the unit on unsteady
surfaces. Do not install in a site where beam may be interrupted by trees or
plants, consider seasonal changes.
Do not install in places where units
may be splashed continuously by
dirty water or direct sea spray.
3. Installation Hints
①Remove cover from unit
and slide the mounting
plate to detach it.
②Break grommet on mounting plate
and pull wire through it. Secure
the plate with 4mm screws.
③When exposed wired, break knock-
outs on the rear of unit, pull wire
through as the figure and attach it to
the mounting plate.
④After wiring is completed,
adjust alignment, check
operation and attach cover.
3-1. Wall mount
3-2. Pole mount (Pole size : Φ38 ~ Φ44mm)
①Remove cover from unit and slide the mounting
plate to detach it.
②Attach pole brackets to pole and secure to mounting
plate with screws
4. Response time
Response time
plate
with
screws
.
③Attach sensor body.
④Pull through wire.
⑤Connect terminals.
⑥After wiring is completed, adjust alignment, check
operation and attach cover.
1. Run at full speed
(6.9m/s) - 50msec. 2. Walk with quick steps (1.2m/s) - 200msec. 3. Walking (0.7m/s) - 300msec. 4. Walk with slow steps (0.5m/s) - 500msec. 5~6. Go over a fence(0.3m/s) - 700msec.
Response
time
adjustment
700ms50ms

5: COM
4: N.O
3: N.C
5. Terminal Arrangement
①②③④⑤⑥
TransmitterReceiver
NO
4
5
Usage
VCC
GND
NO
1
2
Usage
Normal Open
Common
①②
6: Tamper
6. Adjustment and Monitoring
- Monitoring
5
6
GND
Normal Close
2
3
Common
Tamper
Look through view finder on either side
and line-up optics horizontally and vertically
until the opposite unit is visible.
7 Trouble Shooting
Very GoodON3.7 ~ 4V
Alignment GoodON3.0 ~ 3.7V
Alignment againOFFLess than 3.0V
ConditionR:Green LEDMonitoring
Vertical
Adjustment :±10˚
Horizontal
Adjustment :±90˚
Digital
Multi meter
Problem
Power LED dose not light.
Alarm LED does not light when two
beams are broken simultaneously.
No contact under the set condition
Good LED does not operate
7
.
Trouble
Shooting
Possible cause
No power supply.
Bad wiring connection or short.
No power supply.
Bad wiring connection or short.
Resistor short.
Malfunction
Possible Solution
Input DC 10.8 ~18V.
Check wiring connection and repair
if necessary.
Replace.
Replace.
Tx
Rx
8. Specifications & Dimension
Model SASO-PB10S SASO-PB30S SASO-PB60S
Detection system Simultaneous breaking of 2 beams
Infrared beam Double modulation pulsed beams by LED
Protection range Outdoor 10m
Indoor 30m Outdoor 30m Indoor 60m Outdoor 60m Indoor 120m
Max. beam range Outdoor 100m
Indoor 100m Outdoor 300m Indoor 300m Outdoor 600m Indoor 600m
Supply voltage
10 8V
~
18V DC(Non
-
polarity)
75
Supply
voltage
10
.
8V
18V
DC(Non
polarity)
Current 57mA 57mA 57mA
Response time 50msec to 700msec
LED Transmitter Green LED ON : Power ON
Receiver Green LED(Sensitivity Good) / Red ON : When an alarm is initiated
Alarm output Dry contact relay output form C
Contact action : Interruption time + delay time(1~3 sec)
Contact capacity : 30V(AC/DC) 1A or less
Tamper output Dry contact relay output form N/C(Receiver only)
Contact action : Activated when cover is detached
Contact capacity : 30V(AC/DC) 1A or less
Tem
p
erature -20℃ ~ 60℃
163
p
Beam adjustment Horizontal : 180˚ (±90˚), Vertical : 20˚ (±10˚)
Mounting position Out door / In door
Material PC resin(Green)
IP rating IP 44
External dimensions 63 x 163 x 75mm(WxHxD)
Weight Rx : 326g, Tx : 309g Rx : 330g, Tx : 315g
Function Monitor jack output, Frost proof cover
Option Pole attachment(2pcs./set) / Transmitter tamper switch / IP 54
*
Caution : Please consult the instruction manual to ensure safe and proper operation of the product
63
Caution
:
Please
consult
the
instruction
manual
to
ensure
safe
and
proper
operation
of
the
product
.
Specification and design are subject to change without prior notice for improvement.