Sauder Bookcase 414726 User manual

NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
English pg 1-16
Français pg 17-18
Español pg 19-20
Lot # 362947 06/18/14
Purchased: __________________
Be sure to give us a ring before
making any returns. 1-800-523-3987
Bookcase
Barrister Lane Collection | Model 414726
Need help? Visit Sauder.com to view video assembly tips or chat with a live rep.
Prefer the phone? Call 1-800-523-3987.
Share your journey!
sauder.com
Here's one for
the books.

Table of Contents Assembly Tools Required
2-3
4
5-16
17-18
19-20
21-22
23
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Skip the power trip.
This time.
414726 www.sauder.com/servicesPage 2
Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
A RIGHT END (1)
B LEFT END (1)
C UPRIGHT (1)
D UPPER UPRIGHT (2)
E LOWER UPRIGHT (2)
F TOP (1)
G BOTTOM (2)
H SHELF (4)
I BACK (2)
J FRONT SKIRT (1)
K SIDE SKIRT (2)
L SIDE RAIL (2)
M BACK RAIL (1)
N FRONT MOLDING (1)
O RIGHT MOLDING (1)
P LEFT MOLDING (1)
Q SHELF MOLDING (2)

Part Identification Now you know
our ABCs.
414726www.sauder.com/services Page 3
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
D
E
G
H
H
H
I
K
L
Q

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
414726 www.sauder.com/servicesPage 4
BLACK 1-7/8" FLAT HEAD SCREW - 18
2S
BROWN 1" FLAT HEAD SCREW - 13
12S
MOLDING CONNECTOR - 2
19F
NAIL - 91
1N
METAL PIN - 8
1R
ANGLE BRACKET - 6
27G
BLACK 9/16" LARGE HEAD SCREW - 13
1S
HIDDEN CAM - 38
1F CAM DOWEL - 38 2F
SAFETY BRACKET - 1
1G CARD HOLDER - 8 35M
CAM COVER - 6
13P
SCREW COVER - 5
18P
CARD SHEET - 1
38M
SILVER 3/8" MACHINE SCREW - 16
97S

Step 1 Look for this icon. It means a
video assembly tip is available at
www.sauder.com/services/tips
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å Push thirty-eight HIDDEN CAMS (1F) into the ENDS (A
and B), UPRIGHT (C), BOTTOMS (G), and SHELVES (H).
Then, insert the metal end of a CAM DOWEL (2F) into
each HIDDEN CAM.
414726www.sauder.com/services Page 5
A
B
C
G
H
G
H
H
H
Arrow
1F
2F
(38 used)
Arrow
1F
2F
Insert the metal end of the CAM
DOWEL into the HIDDEN CAM.
Arrow
Do not tighten the HIDDEN CAMS in this step.
Scan this QR code or go to this address:
http://qr.sauder.com/?ID=1711
to watch a video on how to assemble your unit.

Step 2
å Tap two MOLDING CONNECTORS (19F) into the notches
in the MOLDINGS (N, O, and P).
414726 www.sauder.com/servicesPage 6
Flat end
Flat end
Use your hammer to tap the MOLDING CONNECTORS (19F) into the notches in the MOLDINGS.
19F
19F
NO
P

å Fasten the RAILS (L and M) to the TOP (F). Use nine
BLACK 1-7/8" FLAT HEAD SCREWS (2S).
Step 3
414726www.sauder.com/services Page 7
F
M
L
L
Surface with fewer holes
Long finished edge
Finished surface
BLACK 1-7/8" FLAT HEAD SCREW
(9 used in this step)
2S
Remember:
Righty tighty.
Lefty loosey.

Step 4
å Carefully turn your TOP over.
å Fasten the MOLDINGS (N, O, and P) to the TOP (F). Use
nine BROWN 1" FLAT HEAD SCREWS (12S).
å NOTE: Do not overtighten the SCREWS into the TOP.
414726 www.sauder.com/servicesPage 8
F
Surface with
more holes
N
O
P
Long finished edge
BROWN 1" FLAT HEAD SCREW
(9 used in this step)
12S

å Fasten the UPRIGHT (C) to the TOP (F). Tighten two HIDDEN CAMS.
å Insert four METAL PINS (1R) into the UPPER UPRIGHTS (D).
å Insert the METAL PINS (1R) in the end of the UPPER UPRIGHTS (D)
into the holes in the TOP (F).
Step 5
414726www.sauder.com/services Page 9
F
1R
Surface with
more holes
D
D
C
Surface with
HIDDEN CAMS
1R
Start Tighten
Arrow
Minimum
190 degrees
Caution
Risk of damage or
injury. HIDDEN CAMS
must be completely
tightened. HIDDEN
CAMS that are not
completely tightened
may loosen, and parts
may separate. To
completely tighten:
Arrow
Maximum
210 degrees
Finished edge
Finished edge
Long finished edge
Do not stand the unit upright without the
BACK fastened. The unit may collapse.
Caution

Step 6
å Fasten two SHELVES (H) to the UPRIGHT (C). Tighten four
HIDDEN CAMS.
å Fasten the SHELVES (H) to the UPPER UPRIGHTS (D). Use
four BLACK 1-7/8" FLAT HEAD SCREWS (2S).
å Insert four METAL PINS (1R) into the LOWER UPRIGHTS (E).
å Insert the METAL PINS (1R) in the end of the LOWER
UPRIGHTS (E) into the holes in the SHELVES (H).
414726 www.sauder.com/servicesPage 10
D
D
C
H
H
E
E
Surface with
HIDDEN CAMS
Surface with
HIDDEN CAMS
Finished edge
Finished edge
1R
1R
Long edge with
HIDDEN CAMS
BLACK 1-7/8" FLAT HEAD SCREW
(4 used in this step)
2S
Arrow
Minimum
190 degrees
Maximum
210 degrees