Sauder Barrister Lane 418270 User manual

Need help? Visit Sauder.com to view video assembly tips or chat with a live rep.
Prefer the phone? Call 1-800-523-3987.
Share your journey!
sauder.com
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
Enlish p 1-40
Français p 41-44
Español p 45-48
Lot # 373983 06/26/15
Purchased: __________________
Be sure to ive us a rin before
makin any returns. 1-800-523-3987
L-Shaped Desk
Barrister Lane Collection | Model 418270
Business or pleasure.
Works both ways.

Table of Contents Assembly Tools Required
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Skip the power trip.
This time.
2-3
4-5
6-40
41-44
45-48
49-50
51
A RIGHT END (1)
B LEFT END (1)
C RIGHT UPRIGHT (1)
D LEFT UPRIGHT (1)
E LARGE TOP (1)
F SMALL TOP (1)
G BOTTOM (2)
H MODESTY PANEL (2)
I SHELF (1)
J RIGHT BACK (1)
K LEFT BACK (1)
L BACK (2)
M DOOR (1)
N ADJUSTABLE SHELF (1)
O BASE (2)
P SIDE SKIRT (4)
Q LARGE DRAWER FRONT (1)
R DRAWER FRONT (1)
S PENCIL DRAWER FRONT (1)
T SIDE RAIL (2)
U RIGHT RAIL (1)
V LEFT RAIL (1)
W DRAWER UPRIGHT (1)
X EXTENSION BLOCK (1)
Y CONNECTOR PLATE (2)
Z LONG RIGHT MOLDING (1)
AA LONG LEFT MOLDING (1)
BB RIGHT MOLDING (1)
CC LEFT MOLDING (1)
DD END MOLDING (4)
EE DRAWER BRACE (1)
B26 PENCIL DRAWER BOTTOM (1)
D14 LARGE RIGHT DRAWER SIDE (1)
D15 LARGE LEFT DRAWER SIDE (1)
D24 RIGHT DRAWER SIDE (1)
D25 LEFT DRAWER SIDE (1)
D78 LARGE DRAWER BACK (1)
D109 DRAWER BACK (1)
D266 PENCIL RIGHT DRAWER SIDE (1)
D267 PENCIL LEFT DRAWER SIDE (1)
D466 PENCIL DRAWER BACK (1)
D467 PENCIL DRAWER BOX FRONT (1)
D716 DRAWER BOTTOM (2)
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the ede
to help distinuish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
Part Identification
418270 www.sauder.com/servicesPae 2

Part Identification
418270www.sauder.com/services Pae 3
A
B
C
D
E
F
G
H
I
J
K
L
M
N
OP
Q
R
S
T
U
V
W
X
Y
Z
AA
BB
CC
DD
EE
G
H
L
O
P
P
P
Y
DD
DD DD
T
B26
D14
D15
D24
D25
D78
D109
D266
D267
D466
D467
D716
D716

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
FILE GLIDE - 2
4B
GG EXTENSION SLIDE - 2
FF EXTENSION RAIL - 2
(EXTENSION SET SHOWN SEPARATED)
35GA CABINET RIGHT - 2 35GB CABINET LEFT - 2
35GC DRAWER RIGHT - 2 35GD DRAWER LEFT - 2
METAL BRACKET - 7
4G
GROMMET CAP - 3
1P METAL PIN - 4 1R
MOLDING
CONNECTOR - 2
19F
10A SLIDE CAM - 4
MAGNETIC CATCH - 1
3I
GROMMET - 3
10P
STRIKE PLATE - 1
6I
NAIL - 30
1N
HIDDEN CAM - 23
1F CAM DOWEL - 23 2F
KNOB - 1
69K PULL - 3
70K
33M DECORATIVE
END - 2 34M DECORATIVE
BACKPLATE - 1
RUBBER SLEEVE - 4
2R
73M DECORATIVE
POST - 2
42H HINGE - 2
418270 www.sauder.com/servicesPae 4

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
GOLD 1" MACHINE SCREW - 2
50S
BLACK 9/16" LARGE HEAD SCREW - 22
1S
SILVER 1-1/8" FLAT HEAD SCREW - 24
10S
15S SILVER 5/8" MACHINE SCREW - 2
BLACK 7/8" LARGE HEAD SCREW - 2
17S
GRAY 1-3/8" MACHINE SCREW - 2
39S
BLACK 1-7/8" FLAT HEAD SCREW - 31
2S
BLACK 7/8" MACHINE SCREW - 2
37S
3S GOLD 5/16" FLAT HEAD SCREW - 24
BLACK 1/2" FLAT HEAD SCREW - 1
11S
BLACK 1" PAN HEAD SCREW - 8
60S SILVER 1-1/2" MACHINE SCREW - 1 95S
418270www.sauder.com/services Pae 5
30S BLACK 1-9/16" FLAT HEAD SCREW - 14
BLACK 1-1/2" PAN HEAD SCREW - 2
49S

Step 1 Look for this icon. It means a
video assembly tip is available at
www.sauder.com/services/tips
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratchin your unit or the floor.
å Push twenty-three HIDDEN CAMS (1F) into the ENDS (A
and B), UPRIGHTS (C, D,and W), MODESTY PANELS (H),
SHELF (I), and BACKS (K and J). Then, insert the metal
end of a CAM DOWEL (2F) into each HIDDEN CAM.
å NOTE: You will only insert two HIDDEN CAMS and CAM
DOWELS into one of the MODESTY PANELS (H).
418270 www.sauder.com/servicesPae 6
Arrow
1F
2F
Do not tihten the HIDDEN CAMS in this step.
Insert the metal end of the CAM
DOWEL into the HIDDEN CAM.
Arrow
(23 used)
Arrow
1F
2F
Do not insert a HIDDEN CAM
and CAM DOWEL into this hole.
A
B
C
D
H
I
J
K
W
H

Step 2
418270www.sauder.com/services Pae 7
å Separate the EXTENSION SLIDES (GG) from the
EXTENSION RAILS (FF) as shown in the enlared
diaram below. Be prepared, the parts are reasy.
å Fasten the EXTENSION RAILS (FF) to the RIGHT END (A)
and RIGHT UPRIGHT (C). Use four GOLD 5/16" FLAT
HEAD SCREWS (3S).
å NOTE: For each EXTENSION RAIL, turn a SCREW into the
hole shown in the enlared diaram. Then, slide the inner
cartride of the EXTENSION RAIL in to find the other hole
that lines up with the hole in the END and UPRIGHT. Turn
a SCREW into this hole.
Open end
GOLD 5/16" FLAT HEAD SCREW
(4 used in this step)
3S
Remember:
Rihty tihty.
Lefty loosey.
Push the black lever in and pull the SLIDE from the RAIL.
GG FF
FF
FF
A
C
Surface with
HIDDEN CAMS Surface with
HIDDEN CAMS
Notched ede
Open end
Notched ede

Step 3
418270 www.sauder.com/servicesPae 8
å Fasten a CABINET RIGHT (35GA) to the RIGHT END (A)
and a CABINET LEFT (35GB) to the RIGHT UPRIGHT (C).
Use four GOLD 5/16" FLAT HEAD SCREWS (3S) throuh
holes #1 and #3.
1
2
3
1
2
3
GOLD 5/16" FLAT HEAD SCREW
(4 used in this step)
3S
Roller end
Roller end
A
C
Surface with
HIDDEN CAMS
Surface with
HIDDEN CAMS
Notched ede
Notched ede

å Fasten the SHELF (I) to the RIGHT END (A) and RIGHT
UPRIGHT (C). Tihten four HIDDEN CAMS.
Step 4
418270www.sauder.com/services Pae 9
Start Tighten
Arrow
Minimum
190 derees
Caution
Risk of damae or
injury. HIDDEN CAMS
must be completely
tihtened. HIDDEN
CAMS that are not
completely tihtened
may loosen, and parts
may separate. To
completely tihten:
Arrow
Maximum
210 derees
A
C
Surface with
HIDDEN CAMS
Surface without
HIDDEN CAMS
Notched ede
Notched ede
I
Surface with
HIDDEN CAMS
Finished ede
Do not stand the unit upriht without the
BACK fastened. The unit may collapse.
Caution

å Fasten a BOTTOM (G) to the RIGHT END (A) and
RIGHT UPRIGHT (C). Use four BLACK 1-7/8" FLAT
HEAD SCREWS (2S).
Step 5
418270 www.sauder.com/servicesPae 10
A
C
G
Unfinished surface
BLACK 1-7/8" FLAT HEAD SCREW
(4 used in this step)
2S
This hole must be here.

å Fasten the other BOTTOM (G) to the LEFT END (B)
and LEFT UPRIGHT (D). Use four BLACK 1-7/8" FLAT
HEAD SCREWS (2S).
Step 6
418270www.sauder.com/services Pae 11
BLACK 1-7/8" FLAT HEAD SCREW
(4 used in this step)
2S
G
Unfinished surface
This hole must be here.
Surface with
HIDDEN CAMS
Surface without
HIDDEN CAMS
Notched ede
Notched ede
B
D

å Fasten the SIDE SKIRTS (P) to the ENDS (A and B)
and UPRIGHTS (C and D). Use eiht BLACK 1" PAN
HEAD SCREWS (60S).
Step 7
418270 www.sauder.com/servicesPae 12
A
C
B
D
P
P
P
P
Lon finished ede
Lon finished ede
Lon finished ede
BLACK 1" PAN HEAD SCREW
(8 used in this step)
60S

Step 8
418270www.sauder.com/services Pae 13
å Fasten six METAL BRACKETS (4G) to the ENDS (A and B), UPRIGHTS (C and D), and BOTTOMS (G). Use six
BLACK 9/16" LARGE HEAD SCREWS (1S).
å NOTE: Be sure the BRACKETS are even with the edes of the ENDS, UPRIGHTS, and BOTTOMS.
å Fasten the BASES (O) to the ENDS (A and B), UPRIGHTS (C and D), and BOTTOMS (G). Use six BLACK 9/16" LARGE
HEAD SCREWS (1S) throuh the METAL BRACKETS on the ENDS, UPRIGHTS, and BOTTOMS and into the BASES.
BLACK 9/16" LARGE HEAD SCREW
(12 used in this step)
1S
4G A
C
B
D
G
G
4G
4G
(6 used)
O
O
Curved ede
Curved ede

Step 9
418270 www.sauder.com/servicesPae 14
å Slide the END MOLDINGS (DD) onto the notched edes of the ENDS (A and B) and UPRIGHTS (C and D).
å *U.S. Patent No. 5,499,886
Notched ede
Slide the END MOLDINGS (DD)
onto the notched edes.
Notched ede
A
C
B
D
DD
DD
DD
DD

å Fasten the SIDE RAILS (T) to the TOPS (E and F). Use
four BLACK 1-7/8" FLAT HEAD SCREWS (2S).
Step 10
418270www.sauder.com/services Pae 15
E
F
T
T
Don't worry. It isn't
Rome. This can be built
in a day.
Surface with more holes
Surface with more holes
BLACK 1-7/8" FLAT HEAD SCREW
(4 used in this step)
2S
Curved ede
Curved ede
Flat ede
Lon flat ede
For support, place packin foam
and maazines under the TOP.
For support, place packin foam
and maazines under the TOP.

å Fasten a CONNECTOR PLATE (Y) to the LARGE TOP (E). Use four
SILVER 1-1/8" FLAT HEAD SCREWS (10S).
Step 11
418270 www.sauder.com/servicesPae 16
E
Surface with more holes
Y
Packin foam
Flat ede
SILVER 1-1/8" FLAT HEAD SCREW
(4 used in this step)
10S
Surface with more holes

Step 12
418270www.sauder.com/services Pae 17
å Tap two MOLDING CONNECTORS (19F) into the notches
in the MOLDINGS (Z, AA, BB, and CC).
Flat end
19F
Flat end
19F
Use your hammer to tap the MOLDING CONNECTORS (19F) into the notches in the MOLDINGS.
Z
BB
AA
CC

Step 13
418270 www.sauder.com/servicesPae 18
E
F
å Fasten the other CONNECTOR PLATE (Y) to the SMALL TOP (F). Use three SILVER 1-1/8" FLAT HEAD SCREWS (10S).
å Fasten the MOLDINGS (Z, AA, BB, and CC) to the TOPS (E and F). Use twelve SILVER 1-1/8" FLAT HEAD SCREWS (10S).
BB
Z
AA
CC
Packin foam
Packin foam
Surface with more holes
Surface with
more holes
Flat ede
Lon
curved
ede
Y
Surface with
more holes
SILVER 1-1/8" FLAT HEAD SCREW
(15 used in this step)
10S
10S

Step 14
418270www.sauder.com/services Pae 19
å Fasten the RIGHT END (A) and RIGHT UPRIGHT (C) to
the LARGE TOP (E) and RIGHT MOLDING (BB). Tihten
four HIDDEN CAMS.
E
Arrow
Minimum
190 derees
Maximum
210 derees
BB
C
A
DD
DD
Z
Packin foam

Step 15
418270 www.sauder.com/servicesPae 20
Arrow
Minimum
190 derees
Maximum
210 derees
E
H
Surface with HIDDEN CAMS
BLACK 1-7/8" FLAT HEAD SCREW
(2 used in this step)
2S
C
MODESTY PANEL with
two HIDDEN CAMS.
Notch
å Fasten the MODESTY PANEL (H) to the LARGE TOP (E).
Tihten two HIDDEN CAMS.
å NOTE: Be sure the MODESTY PANEL with two HIDDEN
CAMS is fastened to the LARGE TOP (E).
å Fasten the MODESTY PANEL (H) to the RIGHT UPRIGHT (C).
Use two BLACK 1-7/8" FLAT HEAD SCREWS (2S).
Packin foam