Sauder 416091 User manual

NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
English pg 1-22
Français pg 23-25
Español pg 26-28
Lot # 374483 07/22/15
Purchased: __________________
Be sure to give us a ring before
making any returns. 1-800-523-3987
Storage Wall
Cannery Bridge Collection | Model 416091
Need help? Visit Sauder.com to view video assembly tips or chat with a live rep.
Prefer the phone? Call 1-800-523-3987.
Share your journey!
sauder.com
Knick-knack
paddywhack,
give your stu a home.

Table of Contents Assembly Tools Required
2-3
4
5-22
23-25
26-28
29-30
31
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Skip the power trip.
This time.
416091 www.sauder.com/servicesPage 2
Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
A RIGHT END (1)
B LEFT END (1)
C RIGHT UPRIGHT (1)
D LEFT UPRIGHT (1)
E LARGE UPRIGHT (2)
F2 TOP (1)
G2 BOTTOM (1)
H2 SHELF (1)
I BACK (1)
J DOOR (3)
K ADJUSTABLE SHELF (6)
L FRONT LEG (2)
M REAR LEG (2)
N BASE (1)
O END MOLDING (2)
P UPRIGHT MOLDING (2)
Q UPPER END MOLDING (2)
R SHELF MOLDING (2)
S SUPPORT (1)
T SIDE SUPPORT (2)

Part Identification Now you know
our ABCs.
416091www.sauder.com/services Page 3
A
B
C
D
E
F2
G2
H2
I
J
K
L
M
N
O
P
Q
R
S
T
J
J
T
O
Q
L
M
E
P
K
R
K
K
K
K

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
416091 www.sauder.com/servicesPage 4
SAFETY BRACKET - 3
1G
BLACK 9/16" LARGE HEAD SCREW - 27
1S BLACK 1-7/8" FLAT HEAD SCREW - 1 2S
BLACK 7/8" MACHINE SCREW - 3
37S
36P CAM COVER - 12 RUBBER SLEEVE - 24
2R
METAL PIN - 24
1R
BLACK 1/2" FLAT HEAD SCREW - 12
11S BLACK 9/16" FLAT HEAD SCREW - 8 32S
CAM SCREW - 14
8F
DOOR STOP - 3
4I
NAIL - 82
1N
HIDDEN CAM - 30
1F CAM DOWEL - 16 2F
KNOB - 3
95K
100S BLACK 2-3/4" FLAT HEAD SCREW - 8
BLACK 1-15/16" FLAT HEAD SCREW - 12
113S
METAL BRACKET - 11
4G 14H CURVED HINGE - 4 40H STRAIGHT HINGE - 2

Step 1 Look for this icon. It means a
video assembly tip is available at
www.sauder.com/services/tips
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å Push thirty HIDDEN CAMS (1F) into the ENDS (A and B),
UPRIGHTS (C and D), LARGE UPRIGHTS (E), TOP (F2),
BOTTOM (G2), and SHELF (H2). Then, insert the metal
end of a CAM DOWEL (2F) into each HIDDEN CAM
except in the ENDS (A and B) and LARGE UPRIGHTS (E).
416091www.sauder.com/services Page 5
Arrow
1F
1F
Arrow
Arrow
1F
2F
Insert the metal end of the CAM
DOWEL into the HIDDEN CAM.
Arrow
Do not tighten the HIDDEN
CAMS in this step.
A
B
C
D
E
F2
G2
H2
E
(30 used)
(16 used)
Do not insert CAM DOWELS into these parts.
Arrow
The arrow in the HIDDEN
CAM must point toward the
hole in the edge of the board.
Hole
Scan this QR code or go to this address:
http://qr.sauder.com/?ID=1625
to watch a video on how to assemble your unit.

Step 2
416091 www.sauder.com/servicesPage 6
8F
å Turn fourteen CAM SCREWS (8F) into the FRONT LEGS (L)
and UPRIGHT MOLDINGS (P). Remember:
Righty tighty.
Lefty loosey.
(14 used)
L
P
L
P

Step 3
416091www.sauder.com/services Page 7
å Turn eight BLACK 9/16" FLAT HEAD SCREWS (32S) into
the ENDS (A and B) until the shoulders of the SCREWS
rest on the surfaces of the ENDS.
å Slide the MOLDINGS (O and Q) onto the ENDS (A and B).
Line up the grooves in the MOLDINGS over the heads of
the SCREWS in the ENDS.
å NOTE: The END MOLDINGS (O) are wider than the
UPPER END MOLDINGS (Q).
å NOTE: Be sure to place the MOLDINGS in
the exact locations shown below.
These edges
should be even.
These edges
should be even.
Shoulder
BLACK 9/16" FLAT HEAD SCREW
(8 used in this step)
32S
A
B
O
Q
O
Q
Surface
without
HIDDEN
CAMS
Surface
without
HIDDEN
CAMS
Edge with smaller holes
Edge with smaller holes
Apply pressure with your hands
as you guide the MOLDINGS over
the SCREWS and onto the ENDS.

Step 4
416091 www.sauder.com/servicesPage 8
å Fasten the FRONT LEGS (L) to the ENDS (A and B).
Tighten eight HIDDEN CAMS.
å Fasten the REAR LEGS (M) to the ENDS (A and B). Use
eight BLACK 2-3/4" FLAT HEAD SCREWS (100S).
L
L
A
B
Surface
with
HIDDEN
CAMS
Surface
with
HIDDEN
CAMS
M
M
This hole
must be here.
These surfaces
should be even.
These surfaces
should be even. This hole
must be here.
Edge with
larger holes
BLACK 2-3/4" FLAT HEAD SCREW
(8 used in this step)
100S
1
2

å Fasten the TOP (F2) and SHELF (H2) to the LEFT END (B).
Tighten four HIDDEN CAMS.
Step 5
416091www.sauder.com/services Page 9
Start Tighten
Arrow
Minimum
190 degrees
Caution
Risk of damage or
injury. HIDDEN CAMS
must be completely
tightened. HIDDEN
CAMS that are not
completely tightened
may loosen, and parts
may separate. To
completely tighten:
Arrow
Maximum
210 degrees
L
B
Surface with
HIDDEN CAMS
H2
F2
Surface without
HIDDEN CAMS
Notched edge
Notched edge
Surface with
HIDDEN CAMS
Do not stand the unit upright without the
BACK fastened. The unit may collapse.
Caution

Step 6
416091 www.sauder.com/servicesPage 10
H2
F2
Notched edge
Notched edge
å Slide the SHELF MOLDINGS* (R) onto the notched edges
of the TOP (F2) and SHELF (H2).
å *U.S. Patent No. 5,499,886
Slide the SHELF MOLDING (R) onto the notched edge.
Slide the SHELF MOLDING (R)
onto the notched edge.
R
R
Groove