Sauder Credenza International Lux 420631 User manual

Need help? Visit Sauder.com to view video assembly tips or chat with a live rep.
Prefer the phone? Call 1-800-445-1527.
Share your journey!
sauder.com
Credenza
International Lux Collection | Model 420631
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
English pg 1-22
Français pg 23-25
Español pg 26-28
Lot #: 501133
Date Purchased: __________________
02/16/17
Be sure to give us a ring before
making any returns. 1-800-445-1527
Designed for
distractions.

Table of Contents Assembly Tools Required
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
WARNING
!
Skip the power trip.
This time.
3
4
5-22
23-25
26-28
29-30
31
95 lbs.
95 lbs.
18-1/2"
18-1/2"
63"
63"
Use of a TV that is too heavy or large is hazardous. A TV that is too heavy will create a risk of a tip-over that can cause severe injury or
death. A TV that is too large for the available space might be accidentally pushed or bumped o the furniture, or subject to tip-over.
• Check the size and weight of your TV. Compare it to the diagram below – before you begin assembly!
• This Sauder unit is designed for use with televisions weighing less than 95 pounds. Never use with a TV that weighs more.
• The size of the television, front-to-back and side-to-side, must fit within the space defined in the diagram.
• Never place the front edge of the TV past the front edge of the TV support shelf (or stop molding – if equipped)
• Never allow the sides of the TV to extend past the side edges of the TV support surface.
• If the TV has a CRT picture tube, the picture tube cone may extend past the rear of the support shelf.
• Be sure to apply the warning label as instructed in the last assembly step. The label provides important safety related information.
Page 2 www.sauder.com 420631

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
A TOP/BOTTOM (2)
B END (2)
C UPRIGHT (2)
D SHELF (2)
E ADJUSTABLE SHELF (2)
F BACK (2)
G SMALL BACK (2)
H DOOR (4)
I DOOR MOLDING (4)
J DOOR PULL (4)
A
B
C
D
E
F
G
H
I
J
A
B
C
D
E
F
H
H
H
J
I
I
JJ
I
Page 3www.sauder.com420631

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
(Refer to the last step for proper location and application)
WARNING LABEL - 1
7
522,68 22,68
95 lbs. 43,09 kg 43,09 kg
HIDDEN CAM - 40
1CAM SCREW - 24 2SMALL CAM SCREW - 16 3
WOOD DOWEL - 36
4HINGE - 8 5HINGE BRACKET - 8 6
BLACK 2" FLAT HEAD SCREW - 16
11
BLACK 1/2" FLAT HEAD SCREW - 16
12 SILVER 1/2" FLAT HEAD SCREW - 16 13
METAL PIN/
RUBBER SLEEVE SET - 8
8
NAIL - 56
10
APPLIQUE CARD - 1
9
Page 4 www.sauder.com 420631

Step 1 Look for this icon. It means a
video assembly tip is available at
www.sauder.com/services/tips
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å Push forty HIDDEN CAMS (1) into the ENDS (B),
UPRIGHTS (C), and SMALL BACKS (G).
(40 used)
B
C
G
B
C
G
1
Arrow
Arrow
The arrow in the HIDDEN
CAM must point toward the
hole in the edge of the board.
Hole
Page 5www.sauder.com420631
Some assembly
(and snacks) required.

å Insert thirty-six WOOD DOWELS (4) into the exact holes
shown in the edges of the ENDS (B), UPRIGHTS (C),
SHELVES (D), and SMALL BACKS (G).
Step 2
4
4
4
B
C
G
B
C
G
D
D
(36 used)
Page 6 www.sauder.com 420631

å Turn twenty-four CAM SCREWS (2) into the exact holes
shown in the TOP/BOTTOMS (A).
Step 3
2
(24 used)
A
A
Page 7www.sauder.com420631
Meet Part (A). This component has
been engineered to be lighter, stronger,
faster… well ok. Not technically faster.
But definitely makes for a sturdier
credenza that’s easier to assemble and
friendlier to the environment.

å Turn sixteen SMALL CAM SCREWS (3) into the holes in
the DOOR MOLDINGS (I).
Step 4
3
(16 used)
I
I
I
I
Page 8 www.sauder.com 420631

å Fasten eight HINGE BRACKETS (6) into the exact holes
shown in the ENDS (B) and UPRIGHTS (C). Use the
SCREWS in the HINGE BRACKETS.
Step 5
6
B
C
B
C
Surface with
HIDDEN CAMS
Surface with
HIDDEN CAMS
Surface with
HIDDEN CAMS
Surface with
HIDDEN CAMS
(8 used)
Page 9www.sauder.com420631

å Fasten the DOOR MOLDINGS (I) to the END (B) and
UPRIGHT (C). Tighten eight HIDDEN CAMS.
å Repeat this step for the remaining END, UPRIGHT, and
DOOR MOLDINGS.
Step 6
Page 10 www.sauder.com 420631
C
B
Surface with
HIDDEN CAMS Surface with
HIDDEN CAMS
I
I
1
2