Sauder Barrister Lane 414729 User manual

NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
English pg 1-24
Français pg 25-28
Español pg 29-32
Lot # 368865 02/03/15
Purchased: __________________
Be sure to give us a ring before
making any returns. 1-800-523-3987
Corner TV Stand
Barrister Lane Collection | 414729
Need help? Visit Sauder.com to view video assembly tips or chat with a live rep.
Prefer the phone? Call 1-800-523-3987.
Share your journey!
sauder.com
Smart stand
for the idiot box.

Table of Contents Assembly Tools Required
3
4
5-24
25-28
29-32
33-34
35
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Use of a TV that is too heavy or large is hazardous. A TV that is too heavy will create a risk of a tip-over that can cause severe injury or
death. A TV that is too large for the available space might be accidentally pushed or bumped o the furniture, or subject to tip-over.
• Check the size and weight of your TV. Compare it to the diagram below – before you begin assembly!
• This Sauder unit is designed for use with televisions weighing less than 50 pounds. Never use with a TV that weighs more.
• The size of the television, front-to-back and side-to-side, must fit within the space defined in the diagram.
• Never place the front edge of the TV past the front edge of the TV support shelf (or stop molding – if equipped)
• Never allow the sides of the TV to extend past the side edges of the TV support surface.
• If the TV has a CRT picture tube, the picture tube cone may extend past the rear of the support shelf.
• Be sure to apply the warning label as instructed in the last assembly step. The label provides important safety related information.
WARNING
!
50 lbs.
50 lbs.
19-1/8"
19-1/8"
43-1/8"
43-1/8"
Skip the power trip.
This time.
414729 www.sauder.com/servicesPage 2

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
A RIGHT END (1)
B LEFT END (1)
C UPRIGHT (1)
D SMALL UPRIGHT (1)
E TOP (1)
F BOTTOM (1)
G SHELF (1)
H CROSS SHELF (1)
I SMALL CROSS SHELF (2)
J BACK (1)
K DOOR (1)
L ADJUSTABLE SHELF (2)
M RIGHT MOLDING (1)
N LEFT MOLDING (1)
O BASE (1)
P RIGHT BASE (1)
Q LEFT BASE (1)
R SMALL END MOLDING (2)
S SHELF MOLDING (1)
T END MOLDING (2)
U FRONT MOLDING (1)
Now you know
our ABCs.
414729www.sauder.com/services Page 3
A
B
C
D
E
F
G
H
I
I
J
K
L
L
M
N
O
P
Q
R
R
S
T
T
U

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
414729 www.sauder.com/servicesPage 4
WARNING
Never use this furniture with a TV that is
too large or too heavy. Severe injury or
death can occur.The TV and furniture
will be unstable and may tip.
-The TV must less than 50 lbs.
-The base of the TV must be able to sit
completely on this shelf.
Refer to instruction book for complete
safety information.
Note: This is a permanent label. Do not
try to remove. Surface will be damaged.
08/05 2 6 9 2 2 0 269220
WARNING LABEL - 1
1L
(Refer to Step 18 for proper
location and application)
3M ANTI-SKID PAD - 1
FOOT - 1
23E
33M DECORATIVE
END - 2 34M DECORATIVE
BACKPLATE - 1
69K DECORATIVE
KNOB - 1
32M DECORATIVE
POST - 2
CORNER
BRACKET - 4
31G 27H HINGE - 2
BLACK 9/16" LARGE HEAD SCREW - 61
1S
METAL
BRACKET - 4
4G
NAIL - 45
1N
METAL PIN - 8
1R RUBBER SLEEVE - 8 2R
CAM DOWEL - 12
2F
HIDDEN CAM - 20
1F
BLACK 1-7/8" FLAT HEAD SCREW - 5
2S
SAFETY
BRACKET - 1
1G
MAGNETIC
CATCH - 1
2I STRIKE
PLATE - 1
6I
BLACK 1/2" FLAT HEAD SCREW - 1
11S
LONG METAL PIN - 2
3R
SILVER 3/4" MACHINE SCREW - 2
20S
SILVER 1-1/2" MACHINE SCREW - 1
95S
TWIST-LOCK®
FASTENER - 3
10F
ANGLE
BRACKET - 10
27G
CAM SCREW - 8
8F
CAM COVER - 8
13P

Step 1 Look for this icon. It means a
video assembly tip is available at
www.sauder.com/services/tips
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å To begin assembly, push a SAUDER TWIST-LOCK®
FASTENER (10F) into the large holes in the MOLDINGS (M
and N) and SMALL UPRIGHT (D).
414729www.sauder.com/services Page 5
10F
N
M
D
Do not tighten the TWIST-LOCK® FASTENERS in this step.

Step 2
å Push twenty HIDDEN CAMS (1F) into the ENDS (A and B),
UPRIGHT (C), BOTTOM (F), and SHELF (G). Then, insert
the metal end of a CAM DOWEL (2F) into each HIDDEN
CAM, except the short edges of the ENDS (A and B).
414729 www.sauder.com/servicesPage 6
A
B
C
G
F
(20 used)
(12 used)
Arrow
1F
2F
Do not tighten the HIDDEN CAMS in this step.
Insert the metal end of the CAM
DOWEL into the HIDDEN CAM.
Arrow
Arrow
Arrow
1F
The arrow in the HIDDEN
CAM must point toward the
hole in the edge of the board.
Hole
Do not insert
CAM DOWELS
into these edges.

å Fasten ten ANGLE BRACKETS (27G) to the ENDS (A and B) and
SHELF (G). Use ten BLACK 9/16" LARGE HEAD SCREWS (1S).
å NOTE: Be sure the edges of the ANGLE BRACKETS are even
with the edges of the ENDS and SHELF.
å Fasten the SMALL END MOLDINGS (R) to the ENDS (A and B).
Use four BLACK 9/16" LARGE HEAD SCREWS (1S).
å NOTE: The SMALL END MOLDINGS do not have holes. Turn the
screws into the grooves of the MOLDINGS. Do not over tighten.
Step 3
414729www.sauder.com/services Page 7
27G
27G
A
B
G
These edges
should be even.
The grooves in the MOLDINGS (R)
should be closer to the top edges.
27G
R
R
BLACK 9/16" LARGE HEAD SCREW
(14 used in this step)
1S
(10 used)
Surface with
HIDDEN CAMS
Surface with
HIDDEN CAMS
Surface with
HIDDEN CAMS
Some assembly
(and snacks) required.

Step 4
å Turn eight CAM SCREWS (8F) into the MOLDINGS (M
and N) and BASES (P and Q).
414729 www.sauder.com/servicesPage 8
8F
Q
P
M
N
(8 used)

å Fasten the RIGHT BASE (P) to the RIGHT END (A).
Tighten two HIDDEN CAMS.
å Fasten the LEFT BASE (Q) to the LEFT END (B). Tighten
two HIDDEN CAMS.
Step 5
414729www.sauder.com/services Page 9
Unfinished surface Unfinished surface
Q
P
A
B
Angled edge
Angled edge
1
2

Step 6
å Fasten the MOLDINGS (M and N) to the TOP (E). Tighten
two TWIST-LOCK® FASTENERS.
414729 www.sauder.com/servicesPage 10
E
M
N
How to use the SAUDER TWIST-LOCK®FASTENER
1. Insert the dowel end of the FASTENER into the hole of the
adjoining part.
NOTE: The dowel end of the FASTENER must remain fully
inserted in the hole of the adjoining part while locking
the FASTENER.
2. Tighten the FASTENER with a Phillips screwdriver as tight
as possible.
Dowel end