Sauder Via 419642 User manual

Need help? Visit Sauder.com to view video assembly tips or chat with a live rep.
Prefer the phone? Call 1-800-523-3987.
Share your journey!
sauder.com
Don't sweat the
small stu anymore.
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
English pg 1-13
Français pg 14-15
Español pg 16-17
Lot # 376815 10/12/15
Purchased: __________________
Be sure to give us a ring before
making any returns. 1-800-523-3987
Reception Hutch
Via Collection | Model 419642

Table of Contents Assembly Tools Required
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
3
4
5-13
14-15
16-17
18
19
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
419642 www.sauder.com/servicesPage 2
Electric drill with 1/4" bit
(ONLY in indicated step)

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
A RIGHT END (1)
B LEFT END (1)
C TOP (1)
D BACK (1)
E VALANCE (1)
F BULLETIN BOARD (1)
A
B
C
D
E
F
419642www.sauder.com/services Page 3

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
BLACK 9/16" LARGE HEAD SCREW - 10
1S
ANGLE BRACKET - 5
5G
BROWN 7/16" LARGE HEAD SCREW - 8
6S
BLACK 2-1/4" FLAT HEAD SCREW - 4
26S
TOUCH-UP PEN - 1
10M
7F TWIST-LOCK®FASTENER - 4 13F MINI TWIST-LOCK®
FASTENER - 8
61P TWIST-LOCK®
FASTENER COVER - 4
62P MINI TWIST-LOCK®
COVER - 4 CORD COVER - 4
66P
BULLETIN BOARD
BRACKET - 8
63G
419642 www.sauder.com/servicesPage 4

Step 1 Look for this icon. It means a
video assembly tip is available at
www.sauder.com/services/tips
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å To begin assembly, push a SAUDER TWIST-LOCK®
FASTENER (7F) into the large holes in the ENDS (A and B).
å Push a SAUDER MINI TWIST-LOCK® FASTENER (13F)
into the indicated holes in the BACK (D).
419642www.sauder.com/services Page 5
A
B
D
7F
13F
13F
13F

å Fasten the ENDS (A and B) to the BACK (D). Tighten four
MINI TWIST-LOCK® FASTENERS.
Step 2
419642 www.sauder.com/servicesPage 6
A
B
D
Surface with MINI TWIST-LOCK® FASTENERS
How to use the SAUDER TWIST-LOCK®FASTENER
1. Insert the dowel end of the FASTENER into the hole of the
adjoining part.
NOTE: The dowel end of the FASTENER must remain fully
inserted in the hole of the adjoining part while locking
the FASTENER.
2. Tighten the FASTENER with a Phillips screwdriver as tight
as possible.
Dowel end
Edge with TWIST-LOCK®
FASTENERS
Edge with TWIST-LOCK®
FASTENERS

å Lay the TOP (C) flat on the floor with the holes up.
å Fasten the ENDS (A and B) and BACK (D) to the TOP (C).
Tighten four MINI TWIST-LOCK® FASTENERS and four
TWIST-LOCK® FASTENERS.
Step 3
419642www.sauder.com/services Page 7
A
B
D
C

Step 4
419642 www.sauder.com/servicesPage 8
å Fasten five ANGLE BRACKETS (5G) to the TOP (C). Use five
BLACK 9/16" LARGE HEAD SCREWS (1S).
å Fasten the VALANCE (E) to the TOP (C).
Use five BLACK
9/16" LARGE HEAD SCREWS (1S).
å NOTE: Turn the SCREWS into the groove of the
VALANCE. Do not overtighten the SCREWS.
å Fasten the BULLETIN BORAD BRACKETS (63G) to
the BACK (D). Use eight BROWN 7/16" LARGE HEAD
SCREWS (6S). Do not tighten the SCREWS.
BLACK 9/16" LARGE HEAD SCREW
(10 used in this step)
1S
5G
63G
63G
BROWN 7/16" LARGE HEAD SCREW
(8 used in this step)
6S
CE
D

Step 5
419642www.sauder.com/services Page 9
å Carefully position the Hutch onto its back edges.
å You may purchase a light at your local hardware store. If you
choose to do this, use the pre-drilled holes in the TOP (C)
inserting the cord in the groove in the BACK (D).
å Insert the CORD COVERS (66P) in the groove at the top and
bottom edges of the BACK (D) regardless of whether or not
you purchased a light.
å Push a TWIST-LOCK® FASTENER COVER (61P) onto any
visible TWIST-LOCK FASTENER®.
å Push a MINI TWIST-LOCK® FASTENER COVER (62P)
onto the MINI TWIST-LOCK FASTENERS® along the top
edge of the BACK (D).
66P
66P
D
C
Use these holes for
your purchased light.
To cover MINI TWIST-LOCK® FASTENERS
62P
Notch
Notch
Notch
Notch
66P
66P
61P
61P
To cover TWIST-LOCK® FASTENERS
(4 used)

å Set the BULLETIN BOARD (F) onto the bottom four
BULLETIN BOARD BRACKETS (63G).
å Now, slide the top BULLETIN BOARD BRACKETS (63G)
down so they wrap around the BULLETIN BOARD.
Step 6
419642 www.sauder.com/servicesPage 10
F
F
63G