Sauder Entertainment Credenza 412922 User manual

NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
English pg 1-28
Français pg 29-32
Español pg 33-36
Lot # 372783 05/18/15
Purchased: __________________
Be sure to give us a ring before
making any returns. 1-800-523-3987
Entertainment Credenza
Carson Forge Collection | 412922
Need help? Visit Sauder.com to view video assembly tips or chat with a live rep.
Prefer the phone? Call 1-800-523-3987.
Share your journey!
sauder.com
It stands. You sit.
A thing of beauty,
this one.

Table of Contents Assembly Tools Required
3
4-5
6-28
29-32
33-36
37-38
39
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Use of a TV that is too heavy or large is hazardous. A TV that is too heavy will create a risk of a tip-over that can cause severe injury or
death. A TV that is too large for the available space might be accidentally pushed or bumped o the furniture, or subject to tip-over.
• Check the size and weight of your TV. Compare it to the diagram below – before you begin assembly!
• This Sauder unit is designed for use with televisions weighing less than 135 pounds. Never use with a TV that weighs more.
• The size of the television, front-to-back and side-to-side, must fit within the space defined in the diagram.
• Never place the front edge of the TV past the front edge of the TV support shelf (or stop molding – if equipped)
• Never allow the sides of the TV to extend past the side edges of the TV support surface.
• If the TV has a CRT picture tube, the picture tube cone may extend past the rear of the support shelf.
• Be sure to apply the warning label as instructed in the last assembly step. The label provides important safety related information.
WARNING
!
135 lbs.
135 lbs.
15-1/2"
15-1/2"
60-3/4"
60-3/4"
Skip the power trip.
This time.
412922 www.sauder.com/servicesPage 2

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
A RIGHT END (1)
B LEFT END (1)
C RIGHT UPRIGHT (1)
D LEFT UPRIGHT (1)
E TOP (1)
F FLIP TOP (1)
G BOTTOM (1)
H SMALL BOTTOM (1)
I SHELF (1)
J SMALL BACK (1)
K DOOR (2)
L BACK (1)
M ADJUSTABLE SHELF (4)
N SMALL ADJUSTABLE SHELF (1)
O LEFT FRONT LEG (1)
P RIGHT FRONT LEG (1)
Q REAR LEG (2)
R DRAWER FRONT (1)
V SKIRT (1)
M75 END MOLDING (4)
X TOP MOLDING (1)
Y EXTENSION BLOCK (1)
D44 RIGHT DRAWER SIDE (1)
D45 LEFT DRAWER SIDE (1)
D62 DRAWER BACK (1)
D701 DRAWER BOTTOM (1)
Now you know
our ABCs.
412922www.sauder.com/services Page 3
A
B
C
D
E
F
G
H
I
J
K
K
L
M
M
M
M
N
O
P
Q
R
V
M75
M75
M75
M75
X
Y
Q
D44
D45
D62
D701

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
FELT DISC CARD - 1
MM
METAL BRACKET - 2
HH
ANGLE BRACKET - 5
GG
GROMMET CAP - 2
QQ RUBBER SLEEVE - 20 SS
METAL PIN - 20
TT
BUMPER - 4
OO
UU HINGE - 4 VV SW HINGE - 3
RR GROMMET - 2
DRAWER FRONT
BRACKET - 1
II
PULL - 1
PP
NN CORNER ACCENT - 2
FOOT - 4
JJ CENTER FOOT - 1 KK
FOOT BASE - 1
LL
40CB CABINET LEFT - 1 40CA CABINET RIGHT - 1 40CC DRAWER RIGHT - 1 40CD DRAWER LEFT - 1
HIDDEN CAM - 31
1F CAM DOWEL - 25 2F CAM SCREW - 6 8F
CORD CLIP - 4
YY
KNOB - 2
WW XX BACKPLATE - 2
WARNING
Never use this furniture with a TV that is too
large or too heavy. Severe injury or death
can occur.The TV and furniture will be
unstable and may tip.
-The TV must less than 135 lbs.
-The base of the TV must be able to sit
completely on this shelf.
-Refer to instruction book for complete safety
information.
Note: This is a permanent label. Do not try
to remove. Surface will be damaged.
02/ 02 2 6 9 2 3 2 269232
WARNING LABEL - 1
ZZ
(Refer to the last step for proper
location and application)
412922 www.sauder.com/servicesPage 4

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
412922www.sauder.com/services Page 5
GGG BLACK 9/16" LARGE HEAD SCREW - 18
EEE SILVER 5/8" MACHINE SCREW - 2
BBB BLACK 1-7/8" FLAT HEAD SCREW - 7
AAA BLACK 2-1/4" FLAT HEAD SCREW - 6
DDD BLACK 1-1/8" MACHINE SCREW - 2
HHH SILVER 1/2" MACHINE SCREW - 2
LLL NAIL - 60 JJJ BLACK 1/2" FLAT HEAD SCREW - 14
FFF BLACK 9/16" FLAT HEAD SCREW - 8
CCC BROWN 1-5/8" FLAT HEAD SCREW - 4
GOLD 5/16" FLAT HEAD SCREW - 8
3S 30S BLACK 1-9/16" FLAT HEAD SCREW - 4

Step 1 Look for this icon. It means a
video assembly tip is available at
www.sauder.com/services/tips
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å Push thirty-one HIDDEN CAMS (1F) into the ENDS (A and B),
UPRIGHTS (C and D), BOTTOM (G), SMALL BOTTOM (H),
SHELF (I), and SMALL BACK (J). Then, insert a CAM
DOWEL (2F) into each HIDDEN CAM, except in the long
edges of the ENDS (A and B).
412922 www.sauder.com/servicesPage 6
B
A
C
D
I
G
J
H
Arrow
1F
2F
Arrow
1F
2F
Insert the metal end of the CAM
DOWEL into the HIDDEN CAM.
Arrow
Do not tighten the HIDDEN CAMS in this step.
Do not insert
CAM DOWELS
into these edges.
(25 used)
(31 used)
Scan this QR code or go to this address:
http://qr.sauder.com/?ID=1128
to watch a video on how to assemble your unit.

å Turn six CAM SCREWS (8F) into the FRONT LEGS (O and P).
å Fasten a CORNER ACCENT (NN) to each FRONT LEG (O and P).
Use two SILVER 5/8" MACHINE SCREWS (EEE).
Step 2
412922www.sauder.com/services Page 7
P
O
NN
NN
8F
8F
SILVER 5/8" MACHINE SCREW
(2 used in this step)
EEE

Step 3
å Fasten the FRONT LEGS (O and P) to the ENDS (A and B).
Tighten six HIDDEN CAMS.
412922 www.sauder.com/servicesPage 8
A
B
O
P
Surface
with
HIDDEN
CAMS
1
2
Surface
without
HIDDEN
CAMS
Angled edge
Angled edge
Remember:
Righty tighty.
Lefty loosey.

å Turn eight BLACK 9/16" FLAT HEAD SCREWS (FFF) into the
ENDS (A and B) until the shoulders of the SCREWS rest on the
surfaces of the ENDS.
å Slide the END MOLDINGS (M75) onto the ENDS (A and B).
Line up the grooves in the MOLDINGS over the heads of the
SCREWS in the ENDS and slide them until they are against the
FRONT LEGS (O and P).
å Fasten the REAR LEGS (Q) to the ENDS (A and B). Use
six BLACK 2 1/4" FLAT HEAD SCREWS (AAA).
Step 4
412922www.sauder.com/services Page 9
A
B
AAA
AAA
P
O
Q
Q
BLACK 9/16" FLAT HEAD SCREW
(8 used in this step)
FFF
BLACK 2-1/4" FLAT HEAD SCREW
(6 used in this step)
AAA
Angled edge
Angled edge
Apply pressure with your hands as
you guide the MOLDINGS over the
SCREWS and onto the END.
Shoulder
M75
M75
M75
M75
M75

Step 5
å Fasten the CABINET RIGHT (40CA) and CABINET LEFT (40CB)
to the UPRIGHTS (C and D). Use four GOLD 5/16" FLAT HEAD
SCREWS (3S) through holes #1 and #4.
412922 www.sauder.com/servicesPage 10
Surface with
HIDDEN CAM
Surface with
HIDDEN CAM
1
2
3
4
4
3
2
1
C
D
Curved edge
Curved edge
Roller end
Roller end
GOLD 5/16" FLAT HEAD SCREW
(4 used in this step)
3S