Sauder Boulevard Cafe 420667 User manual

Need help? Visit Sauder.com to view video assembly tips or chat with a live rep.
Prefer the phone? Call 1-800-445-1527.
Share your journey!
sauder.com
Your holder for all
things awesome.
Credenza
Boulevard Cafe Collection | Model 420667
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
English pg 1-28
Français pg 29-32
Español pg 33-36
Lot #: 509855
Date Purchased: __________________
10/17/17
Be sure to give us a ring before
making any returns. 1-800-445-1527

Table of Contents Assembly Tools Required
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
Hammer
Not actual size
3
4
5-28
29-32
33-36
37-38
39
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Skip the power trip.
This time.
Use of a TV that is too heavy or large is hazardous. A TV that is too heavy will create a risk of a tip-over that can cause severe injury or
death. A TV that is too large for the available space might be accidentally pushed or bumped o the furniture, or subject to tip-over.
• Check the size and weight of your TV. Compare it to the diagram below – before you begin assembly!
• This Sauder unit is designed for use with televisions weighing less than 70 pounds. Never use with a TV that weighs more.
• The size of the television, front-to-back and side-to-side, must fit within the space defined in the diagram.
• Never place the front edge of the TV past the front edge of the TV support shelf (or stop molding – if equipped)
• Never allow the sides of the TV to extend past the side edges of the TV support surface.
• If the TV has a CRT picture tube, the picture tube cone may extend past the rear of the support shelf.
• Be sure to apply the warning label as instructed in the last assembly step. The label provides important safety related information.
WARNING
!
70 lbs.
70 lbs.
16-1/2"
16-1/2"
60"
60"
Page 2 www.sauder.com 420667

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
A RIGHT END (1)
B LEFT END (1)
C TOP (1)
D BACK (1)
E UPRIGHT (1)
F ADJUSTABLE SHELF (2)
G DOOR RAIL (2)
H SHELF (1)
I BOTTOM (1)
J REAR LEG (1)
K FRONT LEG (1)
L LEFT DOOR (1)
M RIGHT DOOR (1)
N FLIP UP DOOR (1)
O LEFT DRAWER SIDE (1)
P DRAWER BACK (1)
Q DRAWER BOTTOM (1)
R RIGHT DRAWER SIDE (1)
S DRAWER BRACE (1)
T DRAWER FRONT (1)
A
B
C
DE
F
F
G
G
H
I
J
K
LM
N
OP
Q
R
S
T
Page 3www.sauder.com420667

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
BLACK 1/2" ALLEN HEAD SCREW - 3
20
CAM COVER CARD - 1
14
LARGE HIDDEN
CAM - 18
3SMALL HIDDEN
CAM - 6
4
WOOD
DOWEL - 29
7
BLACK 1/2" PAN HEAD SCREW - 16
23
SILVER 1/2" FLAT HEAD SCREW - 8
21 BLACK 1/2" FLAT HEAD SCREW - 8
22
BLACK 1-1/2" FLAT HEAD SCREW - 16
18
BLACK 1" FLAT HEAD SCREW - 6
19
BLACK 1-1/2" ALLEN HEAD SCREW - 6
17
ANGLED HEAD
CAM SCREW - 18
5
Angled head
HINGE - 4
13
HINGE BRACKET - 4
12
METAL PIN - 8
8
DOOR STOP - 2
10
PULL - 1
16
(EXTENSION SET SHOWN SEPARATED)
DOOR PULL - 2
15
GROMMET
WITH CAP- 2
11
STRAIGHT HEAD
CAM SCREW - 6
6
Straight head
THREADED
PIN - 2
9
1EXTENSION RAIL - 2 2EXTENSION SLIDE - 2
(Refer to the step 23 for proper
location and application)
WARNING LABEL - 1
24
522,68 22,68
70 lbs. 31,75 kg 31,75 kg
Page 4 www.sauder.com 420667
ALLEN WRENCH - 1
25

Step 1 Look for this icon. It means a
video assembly tip is available at
www.sauder.com/services/tips
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å Push eighteen LARGE HIDDEN CAMS (3) into the
ENDS (A and B), BACK (D), UPRIGHT (E), and SHELF (H).
Arrow (18 used)
Arrow
Arrow
33
The arrow in the HIDDEN
CAM must point toward the
hole in the edge of the board.
Hole
A
B
D
E
H
Page 5www.sauder.com420667

Step 2
å Fasten the HINGE BRACKETS (12) to the LEFT END (B) and
UPRIGHT (E). Use the screws in the HINGE BRACKETS.
å NOTE: Be sure to use the exact holes shown.
B
E
12
12
Page 6 www.sauder.com 420667

Step 3
å Turn eighteen ANGLED HEAD CAM SCREWS (5) into the
ENDS (A and B), TOP (C), and UPRIGHT (E).
Angled head
5(18 used) C
A
B
E
Page 7www.sauder.com420667

Step 4
å Fasten the DOOR RAILS (G) to the RIGHT END (A) and
UPRIGHT (E). Use six BLACK 1" FLAT HEAD SCREWS (19).
å Fasten the DOOR STOPS (10) to the RIGHT END (A) and
UPRIGHT (E). Use four BLACK 1/2" PAN HEAD SCREWS (23).
10
10
BLACK 1" FLAT HEAD SCREW
(6 used for the DOOR RAILS)
19
A
E
BLACK 1/2" PAN HEAD SCREW
(4 used for the DOOR STOPS
23
G
G
Page 8 www.sauder.com 420667

Step 5
å Separate the EXTENSION SLIDES (2) from the
EXTENSION RAILS (1) as shown in the upper diagram
below. Be prepared, the parts are greasy.
å Fasten the EXTENSION RAILS (1) to the RIGHT END (A) and
UPRIGHT (E). Use six BLACK 1/2" FLAT HEAD SCREWS (23).
å NOTE: For each EXTENSION RAIL, turn a SCREW into
the hole shown in the enlarged diagram. Then, slide the
inner cartridge of the EXTENSION RAIL in to find the
other holes that lines up with the holes in the END and
UPRIGHT. Turn a SCREW into these holes.
å NOTE: The EXTENSION SLIDES will be used later for the
DRAWERS.
Use these holes to fasten the EXTENSION
RAIL to the END and UPRIGHT
Push the black lever down and pull the SLIDE from the RAIL.
1
1
1
2
BLACK 1/2" PAN HEAD SCREW
(6 used in this step)
23 Open end
Open end
A
E
Page 9www.sauder.com420667
Just think. The sooner
you do this, the sooner
you do something else.

å Insert three WOOD DOWELS (7) into the BACK (D).
å Fasten the UPRIGHT (E) to the BACK (D), by placing the
back edge of the UPRIGHT over the WOOD DOWELS (7).
Step 6
D
E
7
Surface with HIDDEN CAMS
The DOOR RAIL (G)
should be here.
Page 10 www.sauder.com 420667