sauter THM-N User manual

Sauter GmbH
Ziegelei 1
D-72336 Balingen
E-Mail: [e-mail]
Tel: +49-[0]7433- 9933-199
Fax: +49-[0]7433-9933-149
Internet: www.sauter.eu
Instruction Manual
Motorized horizontal Test Stand
SAUTER THM-N
Version 1.1
02/2018
GB
THM-N-BA-e-1811
PROFESSIONAL MEASURING

2 THM-N-BA-e-1811
GB
SAUTER THM-N
Version 1.1 02/2018
Instruction Manual
Motorized horizontal Test Stand
Thank you for buying a SAUTER motorized horizontal test stand. We hope you are
pleased with the high quality finish of this measurement system with its high repeat-
ability and its big functional range. Compared with its previous version, THM model,
this one now is equipped with a digital display, where an exact reading of the travel
speed, as well as the pre-set and already navigated cycles can be seen and read.
In addition, the new THM-N is equipped with a height adjustable bench vice with
jaws. By means of this, the user gets much better and flexible possibilities of adapta-
tion.
If you have any queries, wishes or helpful suggestions, do not hesitate to call our
service number.
Summarize:
1Scope of delivery........................................................................................... 3
2Photos and drawings with dimensions........................................................ 3
3Warnings ........................................................................................................ 5
4Technical description.................................................................................... 5
4. Operation........................................................................................................ 6
5Adaptation of Force Gauges......................................................................... 6
6Packing, dimensions and weight.................................................................. 6

THM-N -BA-e-1811 3
1 Scope of delivery
- SAUTER THM
- Instruction Manual
2 Photos and drawings with dimensions
View of back side:
View: height adjustable jaw bench vice with a variety of possibilities of adjustment
Fixing screw of the
bench vice carriage
Fixing screw of the
bench vice height
Bench vice height adjustment

4 THM-N-BA-e-1811
Dimensions in mm
Counterclock
wise rot.
Ø: 20
240
550
Left
adjustment
ring
Right
adjustment
ring
Cycle function
ON/OFF
Cycle adjustment & indication
of current state, target value
Velocity adjustment &
indication
Clockwise
rotation
Height alignment
for adjusting the
horizontal test
arrangement
260

THM-N -BA-e-1811 5
3 Warnings
Force measurements which are carried out in a wrong way, may lead to serious inju-
ries of persons and damages on objects. Therefore they may only be performed by
trained staff!
Especially it should be avoided that forces are reacting on the test stand and the
force gauge, which are exceeding the instrument’s limit load (max.) of test stand or
force gauge or which are not reacting in axial direction from the test stand at the
force gauge.
4 Technical description
Maximum admissible charge: 500 Newton
Maximum travel length: 220 mm (secured by electronic end switches)
Travel speed: 50-500 mm/min
Working voltage: 230V two-pin earthed plug
Current rating: 1,5 A
Protection mains supply: 3 A
Control system protection: 1,5 A
Working temperature: 10 to 30 °C
The clamping bench vice is mounted on a height- or axial adjustable mounting plate
Repeating function with cycle adjustment
Cycle indication: current state and target value indication (four-digit)
Can be combined with length measuring device LB (with serial interface) e.g. for use
with AFH FD (force/ displacement) software: Scale length: 200mm, readout: 0.01mm

6 THM-N-BA-e-1811
4. Operation
- Turn on power switch
- Adjust the left and right adjustment- / lock ring (=travel distance)
- Choose between manual operation or cycle testing
- Choose travel speed of travel distance at the controller (regulator)
- Switch on cycle tests with yellow button M/A (red LED lights up):
1. Zeroing of cycle test current state by pressing the blue button
2. Adjustment of cycle target value by pressing the yellow buttons
With button “arrow left” the number has to be chosen (number is flickering)
During the number is flickering, insert desired numerical value at button
“arrow up/down”
Takeover of values when numbers are shining permanently
3. Cycle begins with start „clockwise or counterclockwise movement “
4. End of cycle when the cycle target value is reached
- Please take care of horizontal and axial force effects (force displacement)!
5 Adaptation of Force Gauges
With 4x M 3 screws on the mounting plate provided
6 Packing, dimensions and weight
Net weight: 35 kg
Packing : robust wooden box (710x295x390 mm)
In cases of an electrical overcharge, the test stand has got an electronic fuse
protection. It is incorporated in the socket of the current supply and can be
substituted as necessary (with a screwdriver).
Annotation:
To have a look at the CE Declaration of Conformity, please click onto the following
link: https://www.kern-sohn.com/shop/de/DOWNLOADS/