Savant PAV-AOM8C-10 User manual

PAV-AOM8C | 009-1563-03 | 200110 1 of 2 45 Perseverance Way, Hyannis, MA 02601
Copyright 2020 Savant Systems, LLC Savant.com | 508.683.2500
Box Contents
(1) 16 Channel Audio Output IP Receiver (PAV-AOM8C-10)
(1) Installation Kit (075-0195-xx)
(2) 3-pin Control Connector (028-9351-xx)
(1) 5V DC 3A Power Supply (025-0153-xx)
(1) Product Insert (009-19xx-xx)
Specifications
Environmental
Temperature 32° to 104° C (0° to 40° C)
Humidity 10% to 80% Relative Humidity (non-condensing)
Dimensions and Weight
Height 1.6 in (4.15 cm)
Width 8.5 in (21.50 cm)
Depth 3.7 in (9.33 cm)
Weight Net: 1.4 lb (0.64 kg)
Shipping: 2.3 lb (1.05 kg)
Power
Input 5V DC 3A
Maximum 15 Watts
Power over
Ethernet (PoE) IEEE 802.3af
Networking
Supported
Standard
IEEE 802.1 AVB/TSN switches
IEEE 802.3 Ethernet
Regulatory
Safety and
Emissions
FCC Part 15 CE C-Tick
RoHS Compliant
Minimum Supported Release
Savant Software da Vinci 8.10.1
Network Configuration
To ensure that the IP Address will not change due to a power outage,
a static IP Address or DHCP reservation should be configured. Savant
recommends using DHCP reservation within the router. By using this
method, static IP Addresses for all devices can be managed from a
single UI, avoiding the need to access devices individually.
NOTE: Setting DHCP reservation varies from router to router. Refer to
the documentation for the router to configure DHCP reservation.
Network Requirements
The PAV-AOM8C requires a Audio Video Bridging (AVB) network.
Connect all Savant devices to the same local area network (LAN) or
subnet as the host. Savant recommends not implementing any type
of trac or packet shaping in your network topology for the Savant
devices as this may interfere with performance.
Front Panel
Power Status
A B
APower LED
Green: System has power and is operating
normally.
O: System is not receiving power.
BStatus LED
O: Embedded processor is resetting, or is
powered up, and is booting the embedded
firmware.
Green: Host has established communications with
the embedded system.
Green Blinking: Embedded system is ready, but
no communication has been established with the
host.
Red: Host has determined the firmware needs to
be updated, but a problem occurred during the
process that will initiate a reset.
Red Blinking: Embedded firmware is running, but
has not received a DHCP IP Address.
Amber: Host is updating the embedded
firmware.
Amber Blinking: Embedded system has a valid
link-local IP Address and is connecting to the
host.
Installation
The PAV-AOM8C should be installed on a solid, flat, level surface. The
device will fit on a 1U rack shelf. The location should be dry, well
ventilated, and out of direct sunlight.
IMPORTANT! The PAV-AOM8C must to be connected to a AVB Switch.
Also a Savant AVB audio input device is required.
Rack
The optional RMB-PAVAM2F-xx or RMB-PAVAM2-xx allows two
devices to be mounted side by side. This rack is compatible with all
standard 19-inch National Electrical Manufacturers Association (NEMA)
rack mounts.
The instructions below show the RMB-PAVAM2F-xx, both brackets
install the same way they just face dierent directions.
1. Align the bracket with the device’s mounting points.
2. Attach using the screws provided with the bracket.
Savant® ProAV 16 Channel Audio Output IP Receiver with Control (PAV-AOM8C)
Quick Reference Guide

PAV-AOM8C | 009-1563-03 | 200110 2 of 2 45 Perseverance Way, Hyannis, MA 02601
Copyright 2020 Savant Systems, LLC Savant.com | 508.683.2500
Rear Panel
H
GF
E
D
C
B
A
AReset
Resets the network settings of the device.
Hold Reset Button for 5 seconds while powered
on to clear network settings. Status LED will
rapidly blink red when reset is complete.
B
USB USB 2.0 Type A (reserved for future use).
CGPIO
(2) General Purpose Input/Output.
3-pin Control Connector
See GPIO Wiring for pinouts
GPIO Input: When configured as an input the
processor will look for a low (<0.8V DC) or a high
(>2.4V DC) state.
Minimum 0V DC / Maximum 12V DC.
GPIO Output: When configured as an output, the
port provides a binary output of 0-12V
DC 150mA max.
DRCA Outputs (8) Analog stereo line output (Left & Right)
Direct Line Level 2.1-VRMS Output
E
Ethernet
8-pin RJ-45 port, PoE – 802.3af compliant
10/100/1000 Base-T auto-negotiating port with
Link/Activity LEDs.
Supports Audio Video Bridging (AVB).
FEthernet
Activity LED
Green Blinking: Activity (Rx/Tx).
O: No Activity.
GEthernet Link
LED
Green Solid: Ethernet Link is established.
O: Ethernet link is not established.
HPower Input 5V DC 3A
GPIO Wiring
General Purpose Input/Outputs
(GPIO) are binary I/O ports used
on Savant controllers to trigger an
action within the system. Events
can control a device, such as turning
on an amplifier (output) or detecting
a state change for a device (input) to
perform a workflow. Pin 2 is used for
input or output depending on configuration.
GPIO Pull Down Resistor (PD) Usage
GPIO pins are configured as inputs and are pulled high to 12V while the
host is booting up. To make the GPIO signal low during a host reboot
and/or a power cycle, attach the GPIO 1 pin to the PD pin. The PD pin
is a 1K ohm pull down resistor (to signal ground) which keeps the GPIO
output below 0.8V during processor boot times.
Expansion
Savant AVB devices can be connected in a single system. Providing a
virtual audio switch. That can be configured to suit almost any need.
See the Savant IP Audio Deployment Guide for more information
maximum number of devices.
Additional Documentation
Refer to the following documents located on the Savant Customer
Community for additional information.
–Savant IP Audio Deployment Guide (009-1571-xx)
NOTE: While not shown this
diagram, GPIO 2 follows the
same wiring as GPIO 1.
32
1
Pin 1 Ground
Pin 2 GPIO 1
Pin 3 Pull-Down Jumper 1
G 1 PD1