Savant IRX-LN01 User manual

SmartLink 3-Gang Receiver Wall Plate (IRX-LN01)
Quick Reference Guide
For Product Info
IRX-LN01 | 009-0908-02 | 160706
45 Perseverance Way, Hyannis, MA 02601
Copyright © 2016 Savant Systems, LLC
Savant.com | 508.683.2500
Box Contents
(1) Smart Link 3-Gang Receiver Wall Plate (IRX-LN01)
(1) Install Kit (075-0147-xx)
(1) Faceplate for HDBaseT RX Box (071-0820-xx)
(1) 4-pin Screw down Connector (028-9395-xx)
(4) Mounting Screws – Philips Flat (039-0103-xx)
(1) Quick Reference Guide (this document)
Specifications
Environmental
Temperature
32° to 104° F (0° to 40°C)
Humidity
10% to 90% Relative humidity (non-
condensing)
Dimensions
Without Faceplate
With Faceplate
Height
4.52 in (11.48 cm)
4.72 in (11.99 cm)
Width
6.35 in (16.12 cm)
6.55 in (16.64 cm)
Depth
2.31 in (5.87 cm)
2.4 in (6.10 cm)
Weight
Net: 0.8 lb (0.36 kg)
Shipping: 1.75 lb (0.79 kg)
Power over Ethernet
Support
Standard
IEEE 802.3af
Nominal Power
6 W
Maximum Load
10 W
Regulatory
Safety and
Emissions
FCC Part 15 | CE Mark | C-Tick
RoHS
Compliant
Minimum Supported Release
Savant OS
da Vinci 5.2.1
IMPORTANT: Although HDBaseT transmission technology is much less
susceptible to EMI interference than other transmission technologies,
if possible, Savant recommends that you use shielded Cat5e/Cat6
cable with this product and shielded metal RJ-45 connectors with a
drain wire soldered to the connector for maximum reliability. Shielded
cable and connectors are also recommended to safeguard against
any unpredictable environmental electrical noise which may impact
performance at resolutions above 1080p.
The IRX-LN01 also provides control capabilities for common AV
functions for controlling other devices in the room with two serial
and two IR ports. The unit also contains two Ethernet ports for
connecting local equipment, such as computers, to the local area
network (LAN) for added flexibility.
The IRX-LN01 does not require a local power supply as it is remotely
powered via Power over Ethernet from any IEEE 802.3af compliant
PoE switch.
Front Panel
HDMI Out
HDMI Type A output provides HDMI audio
and video output at video resolutions to
1080p@60hz and graphics resolutions to
1920x1200@60Hz.
TosLink In
Reserved for future use.
RS-232
RJ-45 ports used to transmit serial binary
data.
Reset
Push button used to reset Static IP Address
Reserved
Reserved for future use.
LAN
10/100 Base-T auto-negotiating Ethernet
LAN ports.
Green (right) indicates an Ethernet speed
of 100 Mb.
Off indicates an Ethernet speed of 10 Mb.
Green (left) indicates Ethernet data
activity.
Grounding terminal: optional use
CPU Status
LED
Green indicates the Host has established
communications with the embedded
system.
Green blinking indicates the embedded
system is ready (running with DHCP IP
address), but the Host has not established
communications with the embedded
system.
Off indicates the embedded processor is
resetting or is powered up; and is booting
the embedded firmware.
Red indicates the Host has determined the
firmware needs to be updated, but a
problem occurred during the process that
will initiate a reset.
Red blinking indicates the embedded
firmware is running, but has not received a
DHCP IP Address.
Amber indicates the Host is currently
updating the embedded firmware.
Amber blinking indicates the embedded
system has a valid link-local IP Address and
is waiting to connect to the Host.
Link Status
LED
Green indicates valid link.
Off indicates no link.
IR
Infrared serial transmitter output ports.

IRX-LN01 | 009-0908-02 | 160706
45 Perseverance Way, Hyannis, MA 02601
Copyright © 2016 Savant Systems, LLC
Savant.com | 508.683.2500
Rear Panel
LINK
RJ-45 port used for extended link
connection to input HDMI audio and video
signals (Extended Link Out) from VOM-
LN02 or VOM-LN04.
Grounding terminal: optional use
LAN PoE
RJ-45 Cat5e/Cat6 port allows 10/100
Base-T (auto-negotiating) communication
between a LAN and the embedded CPU at
10/100 data rates.
Green: (right) indicates an Ethernet speed
of 100 Mb.
Off: indicates an Ethernet speed of 10 Mb.
Green: (left) indicates Ethernet data
activity.
Power over Ethernet (PoE) is supported
on this port.
Wiring and Connectors
RS-232 Wiring
Important: If you are using RJ-45 to DB-9 adapters not supplied by
Savant, be sure to terminate any wires required for
communication/control within the adapter. Ensure that all wires
required for communication/control are not terminated in the
connecter. Also, ensure that the unused wires in the connector are cut
to prevent them shorting out, as they are still terminated in the RJ-45
connector on the controller side.
IR Port Layout and Pinouts
Additional Documentation
Additional Documentation is available on the Savant Community.
•4-Port Output Modules: VOM-LN04-01 Quick Reference Guides
•RS-232 Conversion to DB-9 and RS-422/485 Pinout Application
Note
Required System Components
•VOM-LN04-01 - Video output modules using HDBaseT
technology through Cat5e or Cat6 cabling.
•SmartMediaPro - SSP-XXXX
•Savant Host - HST-XXXX or SVR-XXXX
•Ethernet Network - Enterprise-grade network deployment
enabled with PoE IEEE 802.3af standard
Installing the IRX-LN01
To install the IRX-LN01 into a standard 3-gang box, do the following:
1. Take the LINK and LAN PoE cables from inside the 3-gang box
and connect them to their respective ports on the IRX-LN01 as
shown above.
IMPORTANT/Rear Connection Cables: Savant recommends mounting the
IRX-LN01 into a low voltage 3-gang installation box (open back) to
allow room for the rear cable connections. A standard 3-gang junction
box can also be used. Please note the following:
•Do not use shallow installation boxes.
•Do not use cables with a long boot (For example, patch
cables or inadequate bend radius).
2. Carefully slide the IRX-LN01 into the 3-gang box. Ensure the
cables do not get damaged.
3. Align the mounting holes on the IRX-LN01 and 3-gang box and
secure with the four screws.
4. Make required connections to the front of the IRX-LN01.
HELPFUL INFORMATION!!
To avoid HDBaseT signal loss, Savant recommends making a direct
end-to-end (homerun) connection when running the Cat 5e/6/7
cabling. Patch panels, wall plates, or similar types of splicing products
allow noise to be introduced which reduces the quality of the video
and in some instances video loss.