Savant PAV-VOM1CP2 User manual

PAV-VOM1CP2 Quick Reference Guide | 009-2034-00
Copyright 2021 Savant Systems, Inc | 210430
45 Perseverance Way, Hyannis, MA 02601
Savant.com | 508.683.2500
1 of 2
Box Contents
(1) Single Video IP Receiver (PAV-VOM1CP2-xx)
(1) Installation kit (075-0210-xx)
(1) Power Adapter with International Clips (025-0195-xx)
(1) Internation Clips (CN, US, UK, EU & AUS)
(2) Mounting Brackets (071-1093-xx)
(4) M2.5 x 4mm screws (for mounting brackets) (039-0590-xx)
(1) IR Emitter (4ft long) (064-0442-xx)
(1) 3-pin RS232 Control Connector (028-0805-xx)
(1) Product Information and Regulatory Statement (009-1950-xx)
Specifications
Environmental
Temperature 30° to 105° F (0° to 40° C)
Humidity 10% to 90% Relative Humidity (non-condensing)
Dimensions and Weights
Height Width Depth Weight
Device 6.97 in
(17.7 cm)
5.91 in
(15.0 cm)
1.00 in
(2.54 cm)
1.35 lb
(0.61 kg)
Shipping 16.0 in
(40.64 cm)
9.00 in
(22.86 cm)
4.00 in
(10.16 cm)
3.00 lb
(1.35 kg)
Power
Power over
Ethernet (PoE+) IEEE 802.3at
Input Power 12V 2A DC
Nominal Power 16 W
Maximum Power 24 W
1 = at 24 Hz
2 = at 25 Hz
3 = at 30 Hz
4 = at 50 Hz 5 = at 60 Hz
Video
HDR Supported
Supported
Formats
640x4805
720x4806
720x5764
800x6005
1024x7685
1280x7204
1280x7205
1280x10245
1920x10801
1920x10803
1920x10804
1920x10805
1920x12005
3840x21601
3840x21602
3840x21603
3840x21604
3840x21605
4096x21603
4096x21605
Audio
Supported
Formats
Pass-though of all HDMI 2.0 audio formats are
supported.
Compliance
Safety and
Emissions
FCC Part 15 CE C-Tick
RoHS Compliant
Supported Releases
Software
Release da Vinci 9.4 and higher
Network Configuration
To ensure that the IP Address will not change due to a power outage,
Savant recommends using DHCP reservation within the router. By
using this method IP Addresses for all devices can be managed from a
single UI, avoiding the need to access devices individually.
NOTE: Setting DHCP reservation varies from router to router. Refer to
the documentation for the router to configure DHCP reservation.
Front Panel
APower LED O - Device is o. No power applied
Red - Main board is powered
BVideo LED O - No video signal detected
Blue - Video signal detected
CLinkTX LED
O - No valid connection
Blue - Valid link
Blinking - Sending Ethernet Data
DLinkRX LED
O -No valid connection
Blue - Valid link, not receiving Ethernet Data
Blinking - Receiving Ethernet
EStatus
Blue - Reset button is pressed when the
device is powered on
Blinking - Reset button has been released or
the device was powered on without holding
the reset button
FP1 Reserved for future use.
G
Reset
Hold down this button with a pointed
stylus for 20 seconds while powering up
the device to restore the device to factory
default settings
Power Video LinkTx LinkRx Status P1 Reset
BCDEFG
A
Network Requirements
For more information, see the Savant Device Networking Guidelines
on the Savant Customer Community.
Required Components
– Savant Audio/Video over IP Device
– Savant System Host
– Savant qualified 10G Managed Network Switch
– Savant User Interface (Pro App)
– Savant Development Environment (SDE)
Savant® IP Video Single Output Receiver 4K UHD with Control (PAV-VOM1CP2)
Quick Reference Guide

PAV-VOM1CP2 Quick Reference Guide | 009-2034-00
Copyright 2021 Savant Systems, Inc | 210430
45 Perseverance Way, Hyannis, MA 02601
Savant.com | 508.683.2500
2 of 2
RJ-45 10G Ethernet connection.
Transport Distance
Cat6 100ft (30m)
Cat6a 300ft (100m)
Cat7 300ft (100m)
10 GbE
Wiring and Connections
IR connection are made using 3.5 mm IR
Emitter supplied with the device.
IR Wiring
Serial control connection are made
using a 3-pin Control Connector
supplied with the device. The wire slips
into the hole and locks with a screw
located at the top of the connector.
RS-232 Wiring
Rear Panel
Additional Information
Refer to the following documents located on the Savant Customer
Community for additional information.
– Savant IP Video Deployment Guide (009-1977-xx)
– Savant IP Video Network Configuration Guide (009-1552-xx)
– Savant IP Video with Audio Processing Deployment Guide
(009-1621-xx)
Installation
To install the PAV-VOM1CP2 use the mounting screws to attach the
included mounting brackets. Please follow the steps below.
1. Align the bracket using the top holes.
NOTE: This will leave an air gap behind the device.
2. Use mounting screws to attaching the bracket.
If the device is going to be mounted Savant recommends aligning the
device with the rear of the device facing down. This will allow the best
heat dissipation.
Rear Panel
RS232
TX RX G
HDMI Out 10 GbE (PoE+)DC 12V IR Out LAN Audio Out
A B C D
E
F
G H
I
J
K
DC 12V 12V 2A DC
HDMI Out
19-Pin Type A HDMI female digital audio/
video output with locking connector.
Supports HDMI 2.0a.
HDMI 2.0 complaint cable required for 4K
content.
RS232
3-pin Control Connector. Transmits and
receives serial data to and from serial
controllable devices. For pin-out
information, refer to the RS-232 Wiring
section.
10GbE
RJ-45 port.
10G connection to the IP Video 10G switch.
Supports Power over Ethernet (PoE+ IEEE
802.3at standard).
Link LED
Solid Green - Link is established with
2.5/5GBase-T mode.
Solid Amber - Link is established with
10GBase-T mode.
O – No link established.
Link Activity
LED
Amber Blinking - Indicates data activity.
O – No Activity.
IR Out
3.5 mm IR Emitter connection. Transmits IR
signals via an IR Flasher (5V tolerant) to
devices with an IR input or IR receiver.
LAN
1G of reserved network data bandwidth
commonly used to connect any network
compliant device to transmit its data onto
the Ethernet network by sharing the 10G
network link. 8-pin RJ-45 female connection.
IMPORTANT!: Do not connect this port to a
network switch.
Link LED Solid Green - Link is established.
O – No link established.
Link Activity
LED
Amber Blinking - Indicates data activity.
Solid Amber - Connected but there is no
data activity.
O – No Activity.
Audio Out
3.5 mm (1/8 in) Analog Audio connection.
For use information refer to the Savant IP
Video Deployment Guide on the Savant
Customer Community.
A
B
C
D
E
F
G
H
I
J
K
Rack Installation
The PAV-VOM1CP2 can be rack mounted using the RCK-PAVVM8.
(rack purchased separately)
3
2
1
Rx
Tx
G
PIN 1
PIN 2
PIN 3
Receive
Transmit
Ground