Savant PAV-VOMVP1F2 Series User manual

PAV-VOMVP1F2-xx/PAV-VOMVP1CP2-xx QRG | 009-2059-00 45 Perseverance Way, Hyannis, MA 02601
Copyright © 2022 Savant Systems, Inc | 220907 1 of 2 Savant.com | 508.683.2500
Savant IP Video Single Output Receiver 4K with POE+
(PAV-VOMVP1F2/ PAV-VOMVP1CP2)
Quick Reference Guide
Box Contents
(1) IP Video Receiver (PAV-VOMVP1CP2-xx/PAV-VOMVP1F2-xx)
(1) SFP+ module (PAV-VOMVP1F2-xx only)
(1) Installation Kit (075-0210-xx)
(1) Power Adapter with International Clips (025-0195-xx)
(1) International Clips (CN, US, UK, EU & AUS)
(2) Mounting Brackets (071-1093-xx)
(4) M2.5 x 4mm screws (for mounting brackets) (039-0590-xx)
(1) IR Emitter (4ft long) (064-0442-xx)
(1) 3-pin RS232 Control Connector (028-0805-xx)
(1) Product Regulatory Statement (009-1950-xx)
Specification
Environmental
Temperature 32° to 104° F (0° to 40° C)
Humidity 10% to 90% Relative Humidity (non-condensing)
Dimensions and Weights
Device Shipping
Height 0.98 in (2.50 cm) 4.0 in (10.16 cm)
Width 8.46 in (21.50 cm) 9.0 in (22.86 cm)
Depth 5.51 in (13.99 cm) 16.0 in (40.64 cm)
Weight 1.65lb (0.75 kg) 4.8 lb (2.17 kg)
Power
Input Power 12V 2A DC
PoE+ (IEEE 802.3at)
Nominal Power 16 W (PAV-VOMVP1F2-xx)
19 W (PAV-VOMVP1CP2-xx)
Maximum Power 36 W
Compliance
Safety and
Emissions
FCC Part 15 CE C-Tick UKCA
RoHS Compliant
Supported Release
Software Release da Vinci 9.4.3 and higher
Supported Audio and Video Formats
Audio
Supported
Formats
Pass-though of all HDMI audio formats are
supported.
Video
HDR Supported
Dolby® Vision Supported
Supported
Formats
640x48051280x72041920x108043840x21603
720x48051280x72051920x108053840x21604
720x57641280x102451920x108053840x21605
800x60051920x108013840x216014096x21603
1024x76851920x108033840x216024096x21605
1 = @ 24 Hz
2 = @ 25 Hz
3 = @ 30 Hz
4 = @ 50 Hz
5 = @ 60 Hz
Required Components
–Savant IP Video Transmitter
–Savant System Host
–Savant qualified 10G Managed Network Switch
–Savant User Interface
–Savant Development Environment (SDE) and Configuration Tools
Front Panel
System
G
USB HOST
H I
P1
J
USB HID
Video
C
LinkTx
D
USB
F
LinkRx
E
Status
B
Power
A
Item Description
A
Power LED O - Device is o. No power applied.
Red - Main board is powered
B
Status LED Blue - Reset button is pressed when the device is
powered on
Blinking - Reset button has been released or the
device was powered on without holding the reset
button
C
Video LED O - No video signal detected.
Blue - Video signal detected.
D
Link TX LED O - No valid connection
Blue - Valid link
Blinking - Sending Ethernet Data
E
Link RX LED O - No valid connection
Blue - Valid link
Blinking - Receiving Ethernet Data
F
USB Reserved for future use.
GSystem LED Not Used and will remain in the OFF state.
HUSB Host Reserved for future use.
I
USB HID Reserved for future use.
JP1 Reserved for future use.
Networking Guidelines
To ensure that the IP Address will not change due to a power outage,
Savant recommends using DHCP reservation within the router. By
using this method IP Addresses for all devices can be managed from a
single UI, avoiding the need to access devices individually.
NOTE: IP video device requirements and how to manage IP addresses
are available on the Savant Device Netwoking Guidelines on the Savant
Customer Community.
Additional Information
Refer to the following documents located on the Savant Customer
Community for additional information.
–Savant IP Video Deployment Guide (009-1977-xx)
–Savant IP Video Network Configuration Guide (009-1552-xx)
–Savant IP Audio Deployment Guide (009-1571-xx)
–Savant Device Networking Guidelines

PAV-VOMVP1F2-xx/PAV-VOMVP1CP2-xx QRG | 009-2059-00 45 Perseverance Way, Hyannis, MA 02601
Copyright © 2022 Savant Systems, Inc | 220907 2 of 2 Savant.com | 508.683.2500
Rear Panel
DC 12V IR OutIR In
A B C
Loop In
D
HDMI Out
E
RS232
TX RX G
F
10 GbE (PoE+)
G
Audio Out LAN
K
RESET
H
I
L
M
JN
Item Description
APower Input 12V DC
BIR In Not Used
C
IR Out 3.5 mm IR Emitter connection. Transmits IR
signals via an IR Flasher (5V tolerant) to devices
with an IR input or IR receiver.
D
Loop In Reserved for future use.
EHDMI Out 19-Pin Type A HDMI female digital audio/video
output.
Supports HDMI 2.0a
HDMI 2.0 compliant cable required for 4K
content.
FRS-232 3-pin control connector transmits and receives
serial data to and from serial controllable
devices. For pin-out information, refer to the
RS-232 Wiring section to the right.
G10 GbE 10G input from the Audio/Video over IP switch.
SFP+ (PAV-VOMVP1F2-xx)
RJ-45 (PAV-VOMVP1CP2-xx) supports Power
over Ethernet (PoE+ IEEE 802.3at standard).
HLink LED Solid Green - Link is established with
2.5/5GBase-T mode.
Solid Amber - Link is established with 10GBase-T
mode.
O – No link established.
ILink Activity
LED
Amber Blinking - Indicates data activity.
O – No Activity.
JAudio Out 3.5 mm (1/8 in) Analog Audio Output. Outputs
2 Ch PCM audio from the local HDMI input when
2 CH and MC PCM is present. Does not support
down mixing encoded audio. Direct Line Level 2.1
VRMS Output.
KLAN 1G of reserved network data bandwidth
commonly used to connect any network
compliant device to transmit its data onto the
Ethernet network by sharing the 10G network
link. 8-pin RJ-45 female connection.
IMPORTANT!: Do not connect this port to a
network switch.
LLjnk LED Solid Orange - Link is established.
O – No link established.
MLink Activity
LED
Solid Orange - Link is established.
O – No link established.
NReset Hold down this button with a pointed stylus for
20 seconds while powering up the device to
restore the device to factory default settings.
Wiring and Connections
IR Wiring
IR connections are made using 3.5 mm
IR Emitter supplied with the device.
RS-232 Wiring
Serial control connection are made using a 3-pin
Control Connector supplied with the device. The
wire slips into the hole and locks with a screw
located at the top of the connector.
Optical In (PAV-VOMVP1F2-xx)
Enhanced small form-factor pluggable connection. Duplex LC Multi-
mode OM3 Fiber required.
Transport Distance
OM3 multi-mode fiber 1000ft (300m)
10 GbE (PoE+) (PAV-VOMVP1CP2-xx)
RJ-45 10G Ethernet connection.
Transport Distance
Cat6 100ft (30m)
Cat6a 300ft (100m)
Cat7 300ft (100m)
Installation
To install this device use the mounting screws to attach the included
mounting brackets. Please follow the steps below.
1. Align the bracket using the top holes.
NOTE: This will leave an air gap behind the device.
2. Use mounting screws to attaching the bracket.
If the device is going to be mounted Savant recommends aligning the
device with the rear of the device facing down. This will allow the best
heat dissipation.
Rear Panel
Power Input
3
2
1
PIN 1
Ground
PIN 2Transmit
PIN 3
Receive
Rx
Tx
G