Saxby Lighting POLGU10 User manual

POLGU10
Opaz Spike Light

Thank you for purchasing this light fitting.
Please read the instructions carefully before use to ensure safe and satisfactory operation of this product.
Please retain these instructions for future reference.
Warning
Specification
Installation
Layout
Existing fittings must be completely removed before installation of a new product. Before removing the existing
fitting, carefully note the position of each set of wires.
Voltage: 240V 50Hz a.c.
Lamp: 50W GU10 Halogen
IP rating: 54
This is a Class 1 product and must be earthed.
Please read these instructions carefully before commencing any work.
This unit must be fitted by a competent and qualified electrician.
Install in accordance with IEE Wiring regulations and current Building Regulations.
To prevent electrocution switch off at mains supply before installing or maintaining this fitting. Ensure other persons
cannot restore the electrical supply without your knowledge. If you are in any doubt, please consult a qualified
electrician.
This light fitting should be connected to a fused circuit.
If replacing an existing fitting, make a careful note of the connections.
Always use the correct type and wattage bulb. Never exceed the wattage stated.
When changing a bulb, always switch off at the mains and allow the old bulb to cool down before handling.
Dispose of used bulbs carefully and responsibly.
Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist.
Check with your local authority or retailer for recycling advice.
This product is rated at IP54.
This product is not suitable for location in or near a marine environment.
The entire unit gets hot whilst on for a period of time.
If the external flexible cable or cord of this lamp is damaged the lamp must be returned to the service agent for
repair.
•Decide on the position of the luminaire. Depending on the location, an approved outdoor rated plug and
socket may be required. Alternatively an approved outdoor rated external terminal block may be used.
•Avoid locating any cables in positions that would cause a hazard. Position cables and connector block away
from areas where they may be at risk from being cut, trapped or damaged.
•Cables that are to be in walls and concealed underground must be protected using suitable conduit or plastic
trunking.
•Ensure that the ground is suitable for pushing the spike into, and can support the luminaire. Do not install in
very wet or boggy areas.
97mm
340mm

Wiring
Check That
Commissioning
9. Ensure that the fitting is pushed into the ground correctly, and cannot fall over. Ensure that the fitting is 0.5m
from the illuminated surface.
10. Replace fuse or circuit breaker and switch on. Your light is now ready for use.
Plug Fitting
1. The appliance must be connected to a 240 volts AC supply.
2. The appliance can be fitted to a rewireable 3 pin plug fitted
with a 3 amp fuse. Should the fuse require replacement, it
must be replaced with a fuse rated at 3 amp and approved to
BS1362.
3. If the mains plug is unsuitable for the socket outlet or is
removed for any other reason, then the cut off plug should be
disposed of safely to prevent the hazard of electric shock.
4 There is a danger of electric shock if the cut off plug is inserted
into any 13 amp socket outlet.
The wires in the mains lead on this appliance are coloured in
accordance with the following code:
Blue – Neutral
Green / Yellow - Earth
Brown – Live
E
L
N
GREEN/ YELLOW
Earth
Neutral
Live
Fuse
3 Amps
Cord Clamp
BLUE
BROWN
If not fitting to a plug then the product must be wired to a IP44 rated terminal block.
Having correctly identified the wiring from your existing light fitting, connect to the approved outdoor rated
external terminal block in the following way:
Check that.....
You have correctly identified the wires.
The connections are tight.
No loose strands have been left out of the connection block.
Enusre that all cord grips are tightly secured.
Eusure that all seals are re-fitted correctly.
NEUTRAL
EARTH
SWITCHED LIVE
BLUE (N)
GREEN/YELLOW
BROWN (L)
SUPPLY
LIGHT FITTING
4th BLOCK PROVIDED FOR LOOP
TERMINATION IF NECESSARY
SPOTLIGHTS GIVE A CONCENTRATED BEAM OF LIGHT AND MUST NOT BE POSITIONED
ANY CLOSER THAN 0.5M (50CM) TO THE ILLUMINATED SURFACE.
0.5m

We recommend cleaning with a soft dry cloth.
Do not use solvents or abrasive cleaners as these could damage the finish.
Glass parts - Remove and wash in warm water or just use a damp cloth. Do not use abrasive materials as these
will damage the finish.
To prolong the life and keep your outdoor lighting in good condition, it is recommended that periodically it is
cleaned using a soft cloth followed by the application of a light coating of oil, such as WD40.
Do not clean the units with a pressure washer.
Waste electrical products should not be disposed of with household waste. Please recycle where
facilities exist. Check with your Local Authority or retailer for recycling advice.
For your safety, always switch off the supply before changing lightbulbs, or cleaning.
Saxby Lighting Ltd. BH23 3PE
Care and Cleaning
Recycling Advice
Safety Information
The glass shade must be replaced immediately should the glass shade become cracked or dam-
Replace Cracked
Shade
SPOTLIGHTS GIVE A CONCENTRATED BEAM OF LIGHT AND MUST NOT BE POSITIONED
ANY CLOSER THAN 0.5M (50CM) TO THE ILLUMINATED SURFACE.
0.5m
050614
Fitting / Replacing Bulbs
When changing a bulb, always switch off at the mains and allow the bulb to cool before
handling. Dispose of used bulbs carefully. Use a soft cloth to handle bulbs, avoid directly
touching the bulbs as this will shorten their life.
Do not exceed the wattage stated or use a different shape bulb from that indicated on the
fitting.
Enure that the seal is correctly located and that the four screws are tightened
after you have changed the bulb.
GU10 240V
50W MAX