Schacht TL1105 User manual

TABLE LOOM
FLOOR STAND
Assembly InstructIons
Find out more at schachtspindle.com
Schacht Spindle Company 6101 Ben Place Boulder, CO 80301
p. 303.442.3212 f. 303.447.9273
© 2019 Schacht Spindle Company, Inc. 01.19
TL1105
TL1106
TL1107

– 2 – – 3 –
PARTS
2X cross braces
2X inside legs with attached blocks
2X outside legs
1X wooden drill guide (for older
looms only)
TOOLS NEEDED
slotted (at) screwdriver
#2 Phillips screwdriver
3/8" wrench
7/16" wrench
drill and 5/16" drill bit (older looms only)
TABLE LOOM FLOOR STAND
Assembly InstructIons
1. Place the two cross braces
horizontally in front of you, with holes
facing up.
2. Identify the two inside legs with
the blocks attached, and set these parts
perpendicular to the cross braces. e
blocks should be at the top, facing
outward.
3. Attach the lower cross brace:
Insert a barrel nut into each hole of
one of the cross braces. Insert a 1/4-20
x 2" Phillips truss head machine screw
through the bottom hole of an inside leg
and tighten into into the barrel nut in the
lower cross brace (Figure 1). Repeat for
the other inside leg.
4. Attach the upper cross brace: Place
the outside legs, with pins facing up, on
the outer side of the inside legs. Insert
a barrel nut into each hole of the second
cross brace. Insert a 1/4-20 x 3" Phillips
truss head machine screw through the
bottom hole of the outside leg, then
through the middle hole of the inside leg.
Fasten the bolts into the barrel nuts in the
upper cross brace (Figure 1). Repeat with
the other outside leg.
5. Attach the metal support bars:
Insert a 10-24 x 1-1/4" carriage bolt
through the square hole in the metal
support bar. Orient the support bar as
shown in Figure 2, with its jog pointing
inward toward the front of the loom,
HARDWARE
2X metal support bars
2X 10-24 x 1-1/4" carriage bolts
2X 10-24 lock nuts
2X #8 SAE washers
2X 1/4-20 x 1-1/2" carriage bolts
2X 1/4-20 washer wing nuts
2X 1/4-20 x 3" Phillips truss head
machine screws
2X 1/4-20 x 2" Phillips truss head
machine screws
4X 1/4-20 barrel nuts
washer wing nut
Phillips truss head machine
screw lock nut
carriage bolt
barrel nut
washer

– 2 – – 3 –
TABLE LOOM FLOOR STAND
Assembly InstructIons
then from the outer side of the stand,
insert the carriage bolt through the top
hole in an outside leg. en place a #8
SAE washer on the carriage bolt and
secure the bolt with a 10-24 lock nut.
6. From the inner side of the stand,
insert a 1/4-20 x 1-1/2" carriage bolt
through the top hole of the inside leg.
From the outside of the stand, place the
round hole in the metal support bar on
the carriage bolt. Secure the carriage bolt
with the washer wing nut and tighten
by hand. Now go back to the lock nut
attached in Step 5 and tighten it as much
as possible.
7. Repeat steps 5 and 6 for the other
side of the stand and the remaining metal
support bar.
8. Tighten all the bolts. Place the loom
on the stand by lining up the pins on the
top of the stand in the four holes on the
bottom of the loom.
FIGURE 1: TABLE LOOM STAND ASSEMBLY
barrel nuts 1/4-20 x 2" Phillips
truss head machine
screw truss screw
inside leg with
attached block
outside legmetal support bar
FRONT OF STAND
cross braces
1/4-20 x 3" Phillips
truss head machine
screw truss screw
FIGURE 2: METAL SUPPORT BARS
10-24
lock nut
#8 SAE
washer
1/4-20 x 1-1/2"
carriage bolt
10-24 x 1-1/4"
carriage bolt
washer wing nut

– 4 – – PB –
RETROFITTING AN OLDER TABLE
LOOM FOR THE FLOOR STAND
If you have an older model table loom
without holes in the underside of the
base, you need to drill holes in your loom
as follows:
1. Remove the castle from the loom.
Place the loom upside down on a rm
surface.
2. Drill four holes into the loom sides
using a 5/16" drill bit and the wooden
drill guide provided. Align the guide
rmly against the inside of the table loom
leg. Drill each hole to a depth of 3/4".
3. e drill guide has an A and a B end
(Figure 3). For a 4-sha loom, use end A
only (Figure 4).
4. e 8-sha loom has a larger frame,
so the holes at the rear of the loom are
farther from the back legs. Use end A for
the holes at the front of the 8-sha loom
and B for the holes at the rear of the
8-sha loom (Figure 5). •
FIGURE 3: DRILL GUIDE
AB
FIGURE 4: 4-SHAFT TABLE LOOM BASE, UPSIDE DOWN WITH CASTLE REMOVED
A
A
table loom
leg
back beam loom side front beam
FIGURE 5: 8-SHAFT TABLE LOOM BASE, UPSIDE DOWN WITH CASTLE REMOVED
A
B
back beam loom side front beam
table loom
leg